AU-X ANC Planar Magnetic Wireless Over-Ear Headphones User Manual
- October 27, 2023
- AUSOUNDS
Table of Contents
- AU-X ANC Planar Magnetic Wireless Over-Ear Headphones
- CONTENTS
- PRODUCT DESCRIPTION
- STORING YOUR AU-X ANC
- IN-FLIGHT STORAGE
- CHARGE EARBUDS FOR 1 HOUR BEFORE FIRST USE
- Headphone On / Off
- PAIRING
- BLUETOOTH PAIRING
- AUTOMATIC CONNECTION
- NFC FAST PAIRING
- ANC ACTIVE NOISE CANCELLATION
- QUICKLY SWITCH THE MONITOR MODE
- VOICE ASSISTANTS
- AUTO-WEAR DETECTION
- SWAPPING CALLS TO DEVICE
- CONTROLS ( Right Side )
- AUXILIARY
- SPECIFICATIONS
- SAFETY INSTRUCTIONS
- BATTERY WARNING
- WARNING
- CLEANING THE UNIT
- FCC RF EXPOSURE STATEMENT:
- ISEDC RF EXPOSURE STATEMENT
- PRODUCT WARRANTY
- Download
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AU-X ANC Planar Magnetic Wireless Over-Ear Headphones
Ausounds Intelligence, LLC.
15300 Ventura Blvd., Suite 214
Sherman Oaks, California 91403, USA
www.ausounds.com
Designed by Ausounds in California | Made in China
Thank you for purchasing the AU-X ANC Planar Magnetic Wireless Over-Ear headphones. Please read the user manual carefully before using this product, and keep it for future reference.
The AU-X ANC is engineered for performance and is equipped with our AU planar magnetic driver to deliver incredible Hi-Res audio in both wireless Bluetooth® and wired connections. Enjoy your music in any environment with Soundproof Active Noise Cancellation.
CONTENTS
Please check if the following parts in the package are complete.
PRODUCT DESCRIPTION
Charge the headphones for 1 hour before using them for the first time. Connect the AU-X ANC to the USB-C charger. The LED indicator will show a red light to indicate that the headphone is charging. A full charge takes about 2 hours when the battery is fully depleted. Once the LED indicator turns off, the headset is fully charged. This product supports rapid charging and can be used for 2 to 3 hours after 15 minutes of charging.
STORING YOUR AU-X ANC
Safely store your headphones with the included carrying case as shown in the figure below.
IN-FLIGHT STORAGE
Your carrying case is designed with a cable pocket for the provided accessories.
CHARGE EARBUDS FOR 1 HOUR BEFORE FIRST USE
Headphone On / Off
On/Off | Power Button | LED Indicator |
---|---|---|
Power On | Long press for 2 sec | Blue light flashes 2 times |
Power Off | Long press for 3 sec | Blue light is on for 2 sec |
PAIRING
1. Press and hold the power button for 7 seconds and the red and blue LED lights will flash alternately to enter the pairing mode
2. Enable Bluetooth® on your device and enter Bluetooth pairing mode.
3. Select AU-X ANC.
BLUETOOTH PAIRING
Press and hold the power button on your headphone to initiate Bluetooth pairing search mode. On the device you wish to pair with, select Bluetooth settings and enable Bluetooth. In the list of available devices, find and select “AU-X ANC” to initiate pairing. (Android devices vary by system).
AUTOMATIC CONNECTION
The AU-X ANC stores your last connected device in memory. If your headphones are disconnected due to being out of range, they will automatically reconnect once in range. To pair your headphone to a new device press and hold the power button for 7 sec until the headphone enters the search pairing mode. If it is disconnected for more than 30 minutes, select the Bluetooth name in your device to connect again. If it is disconnected for more than 2 hours, it will automatically shut down.
NFC FAST PAIRING
The AU-X ANC is equipped with NFC fast pairing. To use this option, turn on the NFC function of your device. Then simply touch the device to the NFC mark on the headphone as seen below. Hold the headphone against the device until they are paired. Please refer to your devices instruction manual for the designated NFC touch location.
ANC ACTIVE NOISE CANCELLATION
The active noise cancellation function is turned on by default. Toggle through the various modes by short pressing the ANC button twice. The voice will prompt: “ANC ON”, “Monitor mode”, “ANC OFF”.
QUICKLY SWITCH THE MONITOR MODE
Cover the touch panel on the right ear cup with your hand, to switch to ambient sound mode, remove your hand to return to the previous mode.
VOICE ASSISTANTS
To initiate the voice assistant feature touch the center of right ear cup 3 times. Your connected device’s voice function will initiate allowing you to issue vocal commands through your headphone.
AUTO-WEAR DETECTION
The music will automatically pause after removing the headphones, and the touch pad is no longer effective. The music will play automati-cally upon wear detection.
SWAPPING CALLS TO DEVICE
When calling or receiving calls, press and hold the top of the touch pad for 2 sec to switch from the headphones to your device to answer.
CONTROLS ( Right Side )
Play/Pause | Tap the ear cup twice to play or pause your music |
---|---|
Increase volume | Touch and slide the ear cup up to increase the volume. |
Sliding to the edge and holding will continue to increase the volume.
Decrease volume| Touch and slide the ear cup down to reduce the volume.
Sliding to the edge and holding will continue to decrease the volume.
Next track| Touch and slide towards the back of your head to play the previous
track.
Previous track| Touch and slide forward to play the next track
Answer call | Double tap the ear cup |
---|---|
End call | Double tap the ear cup |
Decline call | Press and hold the ear cup for 1 sec |
Voice assistant | Touch the center of the ear cup 3 times |
Switching calls | Touch and hold the center of the right ear cup |
Pairing mode | Press and hold the power button for 7 sec |
AUDIO CONTROLS
CALL CONTROLS
AUXILIARY
To connect your headphones using the auxillary port. Insert the provided 3.5mm plug to your auxillary source device. The auxillary connection overrules any Bluetooth connections and will interrupt audio. Bluetooth will automatically be renabled once the auxillary 3.5mm plug is disconnected.
NOTE: Since auxillary audio does not require power, you can listen to your headphone with the power off using the auxillary connection.
NOTICE: In order to listen to music with Hi-res audio performance, please make sure to use the provided cable instead of wireless connection.
SPECIFICATIONS
Bluetooth Version | BT 5.0 |
---|---|
Bluetooth Protocol | SBC, AAC, aptX, aptX HD |
Bluetooth Range | 10m |
ANC Depth | 28db |
Auto-wear Detection | Yes |
Driver Type | Planar Magnetic Driver |
Driver Size | 61*51mm |
Impedance | 32 ohms |
Frequency Range | 20Hz-40kHz |
SPL | 102 +/-3db |
Battery Life | 25 Hours |
Battery Capacity | 1050mAh |
Charging Time | 2 Hours |
Weight | 357g |
Waterproof level | IPX5 |
SAFETY INSTRUCTIONS
- Do not attempt to make any modifications to the product, including removing or modifying the product, as the damage is not covered by the warranty.
- Do not place the product in extremely high or low ambient temperatures for extended periods of time. Extreme temperatures can cause equipment to deform, and reduce the charging capacity of the device.
- Thunderstorm weather may affect the normal use of the product and there is a risk of electric shock, so please do not use the earphones outside during thunderstorms.
- This product contains small parts. Do not swallow it to avoid danger. Keep the product out of the reach of children.
- Using the product for a long time at high volume may affect your hearing, please control the volume.
- If this product supports active noise cancellation. Please do not turn this function on when walking, driving, or cycling to avoid accidents.
BATTERY WARNING
This product contains lithium battery, please do not disassemble, impact, squeeze or put into fire. Please do not place the product under high temperature or hot sun, beware of explosion. If there is swelling, leakage, odor or any other abnormality in the battery compartment of the product, do not continue to use it. Please dispose of used batteries properly in accordance with local regulations.
WARNING
Do not subject the product to excessive shock. If your product has touch sensor, do not apply stickers or other adhesive items to the touch sensor control panel. Be careful not to catch your finger in the unit when folding. The Bluetooth function may not work with a mobile phone, depending on the signal conditions and the surrounding environment. Do not apply weight or pressure to the product for long periods, including when it is stored, as it may cause deformation. If you experience discomfort while using the product, stop using it immediately. If this product has earpads/ ear tips they may be damaged or deteriorate with long-term use and storage.
CLEANING THE UNIT
When the outside of the product is dirty, clean it by wiping with a soft dry cloth. If the product is particularly dirty, soak a cloth in a dilute solution of neutral detergent, and wring it well before wiping. Do not use solvents such as thinner, benzene, or alcohol, as they may damage the surface.
DO NOT USE THE HEADSET NEAR MEDICAL DEVICES
This product has magnets which may interfere with pacemakers, defibrillators
and programmable shunt valves or other medical devices. Do not put this
product close to these medical devices and the person who use any of these
medical devices. Consult your doctor before using this product, if you have
any concerns.
DO NOT PLACE CARDS WITH MAGNETS
IN THE VICINITY OF THE HEADSET
This product has magnets. Placing cards with magnets in the vicinity of the
product may affect the magnetism of the card and render it unusable.
READ ALL INSTRUCTIONS BEFORE USE AND
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. -
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC RF EXPOSURE STATEMENT:
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.
CAUTION!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
ISEDC STATEMENT
This device complies with Innovation, Science, and Economic Development Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’ Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil nedoit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de classe b est conforme à la norme nmb – 003 du
canada.
ISEDC RF EXPOSURE STATEMENT
The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.
LE PRÉSENT APPAREIL EST CONFORME
Après examen de ce matériel aux conformité ou aux limites d’intensité de champ
RF, les utilisateurs peuvent sur l’exposition aux radiofréquences et la
conformité and compliance d’acquérir. les informations correspondantes.
PRODUCT WARRANTY
Ausounds Intelligence warrants this product to the original purchaser to be free from defects in material and workmanship, under normal conditions for a period of 1-year for parts and labor only from the date of original purchase. Ausounds agrees at our option during the warranty period, to repair any defect in material or workmanship or to furnish an equal product in exchange without repair charges, during the first 365 days. After 365 days, a flat labor rate may be required and payment sent along with the product. Except where prohibited by applicable law, this warranty is nontransferable and is limited to the original purchaser and the country in which the product was purchased. This warranty gives you specific legal rights, and you may also have other rights, including a longer warranty duration that may vary under local laws. If you do not find a solution on our website, please contact the retailer from whom you made your purchase. Valid warranty claims are generally processed through the point-of-purchase retailer during the first thirty (30) days after purchase. This period of time may vary depending on the retailer. If your warranty claim cannot be processed through the point-of-purchase retailer, please contact our support department at support@ausounds.com or call direct at 1-818-873-0113.
Please follow these directions to return your product:
- Contact Ausounds support at support@ausounds.com or 818-873-0113 to receive a return authorization
- Pack the unit in a well-padded sturdy carton if you do not have the original packaging
- Enclose a copy of your sales receipt to validate the date of purchase
- Ausounds will elect to repair or replace the product free of repair charges during the first 365 days. After 365 days, payment for labor may need to be sent with the product. Call customer support at 818-873-0113 or email
support@ausounds.com
Ausounds Intelligence
Attention: Warranty Services
3190 Chicago Ave Riverside, CA 92507-3448 US
NOTE: This warranty does not cover any product which has been subject to
damage due to misuse, neglect, accidental damage, abuse, commercial use, or
any product modifications. This warranty does not cover damage due to improper
operation or maintenance, connection to an improper voltage supply, or
attempted repair by anyone other than Ausounds. This warranty does not cover
products sold AS IS or refurbished units. For consumers, who are covered by
consumer protection laws or regulations in their country of purchase or, if
different, their country of residence, the benefits conferred by Ausounds’
Limited Warranty are in addition to all rights and remedies driven by such
consumer protection laws and regulations , including but not limited to these
additional rights.
National Statutory Rights
Consumers have legal rights under applicable national legislation governing
the sale of consumer goods. Such rights are not affected by the warranties in
this Limited Warranty. In Brazil, remedies include the consumer’s option to
keep the defective product and receive a proportional price reduction.
European Union notice:
Please note that, in the European Union, any warranty period less than two
years shall be increased to two years.
For Australia/New Zealand Consumers Only:
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
This warranty is provided by Ausounds Intelligence, LLC 15300 Ventura Blvd
Suite 214 Sherman Oaks, CA 91403. Contact information for Australia/New
Zealand Consumers Only: Telephone: 1 818-873-0113. For any product/warranty
-related questions, please contact customer support at support@ausounds.com
For Japan Consumers Only:
The Federal Arbitration Act (the “FAA”) applies to the agreement to arbitrate
to the maximum extent allowable. Except as preempted by FAA, the laws of the
State of California, without reference to its choice of laws principles, will
govern this Limited Warranty. With the exception of disputes in small claims
court or in arbitration, You and Ausounds consent to jurisdiction and venue in
the state or federal courts located in Los Angeles County, California, for any
claims arising out of a dispute relating to this Limited Warranty.
Notwithstanding the Section titled “Binding Arbitration and Class Action
Waiver”, if You are a consumer in Japan, You have the right to resolve
disputes before the Tokyo District Court in Japan. Nothing in this Limited
Warranty affects Your rights as a consumer in Japan to rely on mandatory
provisions of Japanese law. Contact information for Japanese Consumers Only:
Telephone:
03-3477-0122. For any product/warranty -related questions, please contact
customer support at support.jp@ausounds.com
Download
AU-X ANC Headphone – User Manual – [ Download PDF ]
AU-X ANC Headphone – Quick Start Guide – [ Download PDF ]