OLIGHT 15 Obulb Pro MCs Motion Sensor Rechargeable Lantern User Manual
- June 6, 2024
- OLIGHT
Table of Contents
15 Obulb Pro MCs Motion Sensor Rechargeable Lantern
User Manual
Thank you for purchasing this Olight product. Please read this manual carefully before use and keep it for future reference!
IN THE BOX
FEATURES
- 7 modes: 7 modes available; including warm white light, red/green/blue/flashing red light, 256-color gradient change, and 7-color fast cycle.
- Shake control: Built-in with an acceleration sensor, it supports stepless adjustment of the brightness by shake control while the light is on in any mode.
- App control: Up to 255 compatible Olight devices, including the Obulb Pro, can be controlled with a mobile app via Bluetooth. It allows you to change mode, brightness level, and color, and check the remaining power and runtime. It also enables group control and data sharing.
- Magnetic bottom: The magnetic bottom attaches to almost any steel surface when combined with the adhesive metal badge.
- Magnetic charging: Quick charging in 3 hours with the magnetic charging cable. The built-in 1650mAh rechargeable battery allows up to 84 hours of runtime after each charge.
- One-button operation: Single click the rubber-coated button to switch on the Obulb Pro and cycle through 7 light modes, or long-press to turn it off.
- Suitable size: Measuring 3.56oz and 2.56*2.28in, the Obulb Pro orb is bigger to light a larger area, but still compact enough to be carried by hand or in backpacks.
- Sturdy build: IPX7 waterproof and 1.5-meter impact-resistant, the Obulb Pro is ready for any environment and adventure.
- Heat dissipation design: The 60 heat dissipation holes prevent damage because of overheating.
- Operating temperature: 0℃ ~ 40℃; Storage temperature: -20℃ ~ 60℃.
SPECIFICATIONS
- All data above are test results according to ANSI/NEMA FL 1-2009 standards.
- The tests are performed using the built-in battery that is fully charged.
- The luminous flux of color fantasy is not fixed due to color changing.
PRODUCT OVERVIEW
UNLOCK THE LIGHT AT FIRST USE
NOTE:
- When the charging cable is connected for the first time, it is normal that the indicator of the cable to flash red once or twice to signal to charge cable detection.
CHARGING
- Before the first use please fully charge the product.
- Connect the USB end of the magnetic charging cable (MCC 1A) to an external USB power source, then attach the other end of the cable to the charging port at the bottom of the product. It takes 3 hours to fully charge.
- Charged at 4.2V/max 1A.
- The red indicator means charging, while the green indicator means charging completed.
- If the battery power is less than 10%, it will flash once when turning on the light or switching the modes, and it will flash once every 30 seconds to remind the user to charge it.
WARNING
Input voltage higher than 5V or voltage fluctuation may damage the IC, leading
to short-circuit and even melting of the charging interface.
BATTERY TYPE
- Built-in 1650mAh 3.7V Rechargeable Lithium Polymer Battery.
HOW TO USE THE ADHESIVE METAL BADGE
- Clean and dry the paste position.
- Gently and carefully peel out the protective film and DO NOT touch the sticky side.
- Paste the sticky side of the adhesive metal badge onto the desired position and press it evenly until it is fixed in place.
- Attach the Obulb Pro to the adhesive metal badge.
DANGER
- DO NOT drop the light or impact it heavily to protect the built-in battery.
- DO NOT charge the product with non-designated power adapters. It may cause battery combustion or even explosion.
- DO NOT throw the product into the fire, which may cause battery combustion, explosion, or unexpected disasters.
WARNING
- DO NOT charge the product if it becomes dirty or wet after being used in a wet place. Before charging, please clean and dry it.
- DO NOT let a pet play with it, in case the pet will bite and damage it.
- DO NOT hit it as a ball, which may cause irreversible damage.
- DO NOT use it as a baby toy.
- It may be damaged or distorted at a temperature of 60℃ or higher.
- DO NOT disassemble or modify the battery, and use the battery for other purposes.
NOTICE
- When the light is turned off, the current output mode will be memorized for the next activation.
- The output brightness will decrease as the battery runs low and its voltage decreases until the light goes off.
- Both MCC1A/MCC3 cables can be used to charge the product.
- The battery has a thermal protection feature. When the battery is working in a temperature higher than 40℃, the Obulb Pro may not be charged.
EXCLUSION CLAUSE
Olight is not liable for damages or injuries sustained resulting from the
usage of the product inconsistent with the warnings in the manual, including
but not limited to using the product inconsistent with the recommended lockout
mode.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following
MEASURES:
Reorient or relocate the receiving antenna. Increase the separation between
the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC (IC) RADIATION EXPOSURE STATEMENT:
This equipment complies with FCC (IC) radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20cm between the radiator & your body.
HOW TO OPERATE
The button is located at the bottom of the product. It can be operated by
pressing the flat part of the bottom, or by pressing the top of the cover if
the product sits securely on a hard surface.
ON/OFF: Single press the button to turn on the light. Press and hold the
button to turn it off, and the mode used the last time will be memorized.
CHANGE OUTPUT: While the light is on, single press the button to cycle through
different modes. The cycle order is as follows: White
light→Red→Green→Blue→Fade between colors→Cycle between colors→Flashing
red→OFF→White light→…
CHANGE BRIGHTNESS LEVEL: When the light is turned on for the first time,
it will activate the lowest brightness on default. The brightness can be
changed by shaking control while the light is on in any mode. With the lowest
brightness on, shaking the light will gradually increase the brightness. After
reaching the highest brightness, shaking will gradually decrease the
brightness. The brightness stays at the current level once you stop shaking.
When the lowest/highest level is reached, you need to stop shaking for at
least 1 second before the brightness can be changed again. If the
highest/lowest level has not been reached and you shake the light to change
the brightness, it will continue the previous increase/decrease trend until it
reaches the highest/lowest level.
RESET THE DEFAULT BRIGHTNESS: While the light is off, press and hold the
switch for about 1 second to access the lowest white light and at this time
the brightness of each mode has been reset to the default value.
LOCKOUT/UNLOCK
While the light is off, press and hold the button for over 2 seconds, the
product will be locked out after a short flash of the lowest white light. In
the lockout mode, if you press the button for less than 1 second, the lowest
white light will turn on momentarily to indicate that it is still in lockout
mode. To unlock it, press and hold the button for over 1 second until it
accesses the lowest white light after a quick blink.
EU-DECLARATION OF CONFORMITY
EU-Declaration of Conformity can be found here:
https://olightworld.com/ec-declaration Dongguan Olight E-Commerce Technology
Co., Ltd
4th Floor, Building 4, Keg Industrial Park, No 6 Zhongnan Road, Changan Town,
Dongguan City, Guangdong, China.
01,10,2022
FCC ID: BCG-E3159A
IC: 579C-E3159A
3.6005.6010.9010
Made in China
Documents / Resources
|
OLIGHT 15 Obulb Pro MCs Motion Sensor Rechargeable
Lantern
[pdf] User Manual
OBULBPRO, 2A44S-OBULBPRO, 2A44SOBULBPRO, 15 Obulb Pro MCs Motion Sensor
Rechargeable Lantern
---|---
References
- Olight | Illuminate Your World.
- Flashlights, Tactical Light, Outdoor Tools - Olight Official Store- Olight
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>