DECORAPORT W60B1NWD LED Mirror User Manual
- June 6, 2024
- DECORAPORT
Table of Contents
DECORAPORPLED MIRROR
LIT UP YOUR BEAUTY
(TOUCH CONTROL MANUAL)
Please Read Before Installation
Please read these instructions carefully before starting the installation and keep in a safe place for future reference. The manufacturer recommends using a qualified Electrician for all electrical wiring procedures. Please turn off all power to the site prior to installation.
Check the contents of the pack carefully before installation. The manufacturer is not responsible for removal reinstallation costs where a defective product has been installed. If any fault is found with materials or workmanship, it must be reported immediately to the manufacturer. Remedial action will be taken, based on information received, on the condition that.
- Full details are supplied to the manufacturer,
- The product has not been modified or tampered with.
- The manufacturer is informed of any damage shortages prior to installation.
- The product has not been installed, or attempts have been made to install it. We do not accept responsibility for any problems that may occur through incorrect installation.
IMPORTANT SAFETY INSTRUCTION
When using electrical furnishing, basic precautions should always be followed, including the following: Read all instructions before using (this furnishing). DANGER – To reduce the risk of electric shock:
- Always unplug this furnishing from the electrical outlet before cleaning or servicing. WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:
- Unplug from outlet before putting on or taking off parts.
- Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
- Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Never operate this furnishing if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the furnishing to a service center for examination and repair.
- Keep the cord away from heated surfaces.
- Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and the like.
- Never drop or insert any object into any opening.
- Do not use outdoors.
- Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
- To disconnect, turn all controls to the off position, then remove plug from the outlet.
- For grounded products the following statement:
“WARNING: Risk of Electric Shock – Connect this furnishing to a properly grounded outlet only. See Grounding Instructions.
GROUNDING INSTRUCTIONS:
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated below. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.
SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Before drilling ensure there are no hidden cables or pipes (water, gas or electrical) behind hanging points. Always wear suitable eye protection when drilling. Ensure the wall surface is able to hold the weight of the complete product. Make sure the power is cut off and installed by qualified electricians. Make sure the wall is flat and can bear the weight of the LED mirror, so as to prevent the products falling down during the installation. Field wiring is not allowed. It needs two people to work together. One person installs the main frame and the other holds the mirror.
STEP 1
Installation tools
STEP 2
Find the horizontal line and make the mark where to drill the screws holes on concrete wall.
STEP 3
Dill at least one screw hole at each corner in the right position on concrete
wall, at least four holes in total. Hammer the mounting anchors on the holes
and screw the Main Frame into anchors by screws.
STEP 4
Hanging the mirror onto the Main Frame.
Dimmer
Press the button , the button will change from red to blue, and the light is
On. Press the button again, the button will change from blue to red, and the
light is Off.
Press the button for 3 seconds, the light will be adjusted from 100% to 10%.
Press the button for another 3 seconds, the light will be adjusted from 10% to
100%.
Anti-fog
Press the button , the button will change from red to blue, and the anti-fog is On. Press the button again, the button will change from blue to red, and the anti-fog is Off.
Mirror & Wall Control
Our mirror controller has the memory function which can memorize the final status of:
- The light on or off.
- The light brightness.
- The light temperature.
- The anti-fog on or off.
Turn on the mirror light and keep it on, and then you can control it by the switch on the wall.
Cold & Warm Light(Optional)
Press this button for three seconds, the light will switch between cold white and warm white.
Bluetooth (Optional)
When the mirror powered on, you will hear a beep sound which means the Bluetooth is active. Now you can search and connect the Bluetooth speakers by your smartphone.The sound volume is also adjusted by your smartphone.
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
IC Warning
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>