WAGNER SteamForce Speed Pro Wallpaper Steamer User Guide

WAGNER SteamForce Speed Pro Wallpaper Steamer

Specifications

• Power Supply: 230 V ~ 50Hz
• Max. Steam Time: 78 Minutes (EU), 95 Minutes (CH)
• Water Capacity: Approximately 5.1 liters
• Power Consumption: 2750W (EU), 2300W (CH)
• Steam Rate: 58 g/min (EU), 47 g/min (CH)
• Weight: Approximately 7.5 kg
• Max. Weight Capacity (for one person): 150 kg

Product Usage Instructions

Safety Precautions

• Always wear suitable protective gloves and goggles while operating the SteamForce Speed Pro to avoid burns and steam exposure.

Unboxing

• Check the package contents which typically include the SteamForce Speed Pro unit, steam hose, user manual, and other accessories.

General Safety Guidelines

• Ensure the power switch is turned off before connecting to the power supply to prevent any electrical hazards.

Preparation

• Securely attach the steam plate to the device without over-tightening to ensure proper functionality.

Operation

• Turn on the device by using the power switch and adjust settings as needed for steam generation. Always monitor the steam levels and water tank capacity during operation.

Descaling

• Regular descaling is recommended to prevent malfunctions. Follow the manufacturer’s instructions for descaling procedures.

Storage

• After use, allow the device to cool down before storing. Empty the water tank and ensure all parts are clean and dry before storing in a safe place.

Maintenance

• Perform routine maintenance checks as per the user manual to ensure the longevity of the product.

FAQ

Q: How do I describe the SteamForce Speed Pro?

A: To descale the device, mix a descaling solution with water as per the manufacturer’s recommendations and run it through the system following the descaling instructions provided.

Q: What should I do if the steam output is low?

A: Check the water level in the tank and ensure it is filled to the recommended level. Also, make sure there are no blockages in the steam nozzle that could be restricting steam flow.

Q: Can I use tap water in the SteamForce Speed Pro?

A: It is recommended to use distilled or demineralized water to prevent mineral build-up in the device. However, if using tap water, regular descaling is necessary.

MANY THANKS FOR PLACING YOUR TRUST IN US

• We would like to congratulate you on purchasing this WAGNER product; we are sure that you will enjoy working with it greatly.
• Please read the Operating Manual carefully and observe the safety information before starting the tool. Store the Operating Manual in a safe place close to the product in case it needs to be used by someone else.
• We would be happy to be of assistance if you have any questions, suggestions, or requests. Please contact us via the phone number included on the back page or via our homepage, www.wagner-group.com.

Explanation of symbols used

Scope of delivery

1. Main unit
2. Water tank
3. Supply cord
4. Control panel
5. Hose connection
6. Steamplates (A) large/(B) small
7. Steam hose 4.9 m
8. Operating manual

Controls and displays on the device

• A ON/OFF switch (lights up when ON)
• B Clean button: Starts the automatic descaling function (press and hold for 3 seconds)
• C Descaling indicator: Lights up when the appliance is to be descaled.
• D Water level indicator: Lights up when the water tank is to be refilled.

General Safety Instructions

• CAUTION! Read all the instructions. Non-observance of the instructions below can cause electric shock, fire, and/or serious personal injuries.
• a) Keep your workplace clean and well-lit. Disorderly or unlit workplaces may result in accidents.
• b) Keep children, unauthorized persons, and animals out of reach of the steamer. You can lose control of the appliance if you are distracted.
• c) The steamer plug must fit into the socket outlet. The plug may not be modified in any form. Do not use adaptor plugs together with protective-earthed tools. Unmodified plugs and suitable sockets reduce the risk of an electric shock.
• d) Avoid physical contact with earthed surfaces such as pipes, heating elements, stoves, and refrigerators. The risk of electric shock increases if your body is earthed.
• e) This device can be used by persons with impaired physical, sensory or mental capacities or a lack of experience and knowledge if they are supervised or have been instructed in the safe use of the device and understand the dangers arising from it.
• f) Children shall not play with the appliance. Risk of scalding or shock.
• g) Never use the tool in hazardous areas that contain flammable liquids, gases, or clouds of dust. Power tools generate sparks that can ignite dust or vapors.
• h) If the supply cord is damaged, it must be replaced by the manufacturer or its service agents to avoid a safety hazard.

Safety Instructions for Steam Wallpaper Strippers

• ATTENTION! When working with hot steam (min.100°C), there is a risk of serious scalding. Hot steam and boiling water can be emitted when the safety valve (fig. 1)is activated due to overpressure in the incorrect operation of the unit.
• Only change position during use, with care. The steam unit, hose, and steamplate can be very hot. Always wear suitable protective clothing/gloves.
• Operate the unit only with pure water without agents or additives. Do not switch the unit on when empty.
• Never point the steamplate / bar at people, animals, at objects sensitive to temperature or other electrical equipment. Do not point liquid or steam directly at electrical devices or equipment containing electrical components, such as the interior of ovens.
• Always ensure that the unit is standing securely in a horizontal position (on the floor). (Fig. 2)
• Be careful of overhead dripping, when using on overhead areas tilt the steamplate away from the face and body and regularly empty the steam plate of any collected condensation.
• Always visually check that the hose and steamplate inlet are not blocked before attempting to use.
• Do not stand on or place objects onto the unit or steam hose. Never overtwist or make kinks in the steam hose and never block the valve. Only carry the device by the handles provided.
• Never pull on the steam hose or supply cord. Whenever accessories are replaced, during maintenance, when filling/refilling or draining, and whenever the steam device is not in use (including breaks between work), the plug on the main cable must be removed from the socket. The device must be kept out of the reach of children whenever it is switched on or cooling down.
• Never overfill the unit. Unplug the unit in the event of overfilling or a fault.
• Use only WAGNER’s original spare parts and accessories!
• Caution! Danger of short-circuits! Cover socket outlets and switches and do not subject them to steam. When using an extension cable: max.10m long – the cord cross-section must be at least 3 x 1,5 mm2. Avoid damage!
• When working in the vicinity of wood/gypsum bases and coated materials these can be impaired by heat or steam. Remedy: Use a heat/steam shield made of cardboard or metal.
• The device must never be left unsupervised while it is plugged into the main power supply. Keep the unit away from children and animals.
• Maximum weight for standing on the unit is 150 kg and no more than 1 person at a time. Ensure a safe stand.
• Do not permit oil, grease, or slippery material to accumulate on the step/platform.
• Do not allow objects to accumulate on the step/platform.
• Do not use a ladder or other device on the step to get greater heights.
• Do not apply impact loads on the step/platform.

Intended use

• The Steam Wallpaper Stripper is solely suited to removing wallpaper. The device may only be used indoors.
• To ensure the long life of the steam wallpaper stripper, unplug and clean your unit immediately and thoroughly after each use.
• CAUTION! – Steam can loosen weak, cracked, porous, or poorly bonded plaster. Check a small area before starting work. Do not hold the steamplate in one position too long and stop if the plaster starts to break.
• PROTECT YOUR HOME – To prevent marks from steam on carpets and soft furnishings it is recommended the unit be placed on a hard flat board. Ensure the unit will not slip or tilt. Dust sheets and newspapers are not suitable.
• The supply cord must be connected to a grounded (3-prong) main socket outlet.
• Arrange the replacement of a worn or damaged supply cord.
• NEVER repair a supply cord.

Extension Leads EU/UK

• If you are using an extension lead it must be rated at a minimum of 16 Amps (110V) / 13 Amps (230V) and fully unwound.
• Do not operate with an extension lead rated less than 16 Amps / 13 Amps as this will cause premature failure of the element which is not covered by the guarantee.

Preparation

• Prepare the old wallpaper well so that you can remove it as quickly as possible and thus in an energy-efficient way.
• To achieve fast paper removal always gently score the areas to be stripped. With heavily embossed, vinyl-coated, or painted papers this is essential.
• Either use a proprietary perforator tool or score the paper with the edge of a wall scraper in a ‘criss-cross’ pattern with 15 cm spacing. As with all decorating work be sure to protect carpets and furniture with covers.

Operation

• Place the unit on a flat surface near the area to be stripped.
• Open the lid of the device and remove the hose, the steam plates, and the power cable.
• Hold the water tank by the sides and pull it out of the device (Fig. 3).
• Place the water tank on a flat surface with the tank opening facing upwards, unscrew the tank cap, and fill it with clean water (no hot water). (Fig. 4). Do not use additives – do not overfill.
• Screw the tank cap back in place and check that it is tight.
• Put the water tank back into the device.
• Fully uncoil the hose and supply cord.
• Screw hose onto threaded outlets of boiler and steamplate, securely by hand. Do not overtighten (Fig. 5).
• Connect the supply cord from the unit to the socket outlet and switch it on.
• Caution! Beware of hot water discharge before steam emission.
• It can take up to 3.5 mins (approx.) before steam is produced – depending on the fill water temperature. DO NOT leave it unattended.
• Once steam is being produced at the steamplate you are ready to commence operation.
• CAUTION! WARNING: Hot liquid or steam can burn.
• The danger of scalding! Steam may also condense into boiling droplets. Steam should not be directed towards electrical appliances.
• Determine what the shortest time is to remove the wallpaper. The faster you work, the more energy you can save.
• Move the steam plate to the section immediately next to where you have just been working and use a wallpaper scraper to remove the section that has just been steamed (Fig. 6).
• You may need to leave the steam plate against the wall for longer periods with some papers or re-steam if not completely removed.

Refilling

• The unit will operate for approximately 78 minutes (230V) / 129 minutes (110V) before requiring refilling (the water level indicator lights up).
• You must never allow the unit to boil dry. There is a safety thermal cut-out device fitted to the unit. If the unit is allowed to boil dry this will operate and prevent further use.
• Switch the unit off and allow it to cool for at least 5 minutes.
• Beware of Steam! The Steam is very hot – wear gloves and keep your face clear.
• Open the lid, hold the water tank by the sides, and pull it out (Fig. 3).
• Place the water tank on a flat surface with the tank opening facing upwards, unscrew the tank cap, and fill it with clean water (no hot water). (Fig. 4). Do not use additives – do not overfill.

Descaling

• Regular descaling is key to your steamer functioning properly. The descaling indicator serves as a guide (depending on the hardness of the water, earlier or later descaling may be advisable).
• Units that are defective due to a lack of descaling are excluded from the guarantee!
• Limescale deposits on the heating element act like an insulating layer and increase energy consumption. Check the heating element visually at regular intervals and descale at an early stage.
• Using standard descaling liquid (citric acid recommended) or tablets, fill a jug with 1.0 liters of water.
• Add the correct amount of descaler following the manufacturer’s guidelines and mix thoroughly.
• Hold the water tank by the sides and pull it out (Fig. 3).
• Place the water tank on a flat surface with the tank opening facing upwards, unscrew the tank cap, and pour in the prepared descaling solution (Fig. 4).
• Screw the tank cap back in place and check that it is tight.
• Open the cover and remove the boiler (Fig. 7+8).
• Empty the boiler.
• If the boiler is not completely emptied, the descaling program will not start and an acoustic signal will sound (5 beeps).
• Insert the boiler into the device and hand-tighten the cover.
• Put the water tank back into the device.
• Switch on the device.
• Press the CLEAN button for about 3 seconds to start the automatic descaling program (an acoustic signal sounds and the descaling indicator starts flashing).
• When descaling is complete (duration approx. 20 minutes), an acoustic signal sounds again and the descaling indicator goes out.
• Switch off the device.
• Clean all connections on the appliance, hose, and steam plate.
• Blow through the steam hose with compressed air to remove deposits and prevent a malfunction.
• Hold the water tank by the sides and pull it out of the device (Fig. 3).
• Open the cover and remove the boiler (Fig. 7+8).
• Rinse the unit thoroughly two or three times with clean water to remove any remaining descaling solution.
• Before reinserting the boiler, check whether condensation has collected at the bottom of the device and, if so, remove it (Fig. 9).
• If no further work is done after descaling, run the machine again with clear water for approx. 20 seconds.

Storage

• Allow the device to cool down.
• Hold the water tank by the sides and pull it out of the device (Fig. 3).
• Open the cover and remove the boiler (Fig. 7+8).
• Rinse out the water tank and boiler with clean water and empty them.
• Check whether condensation has collected at the bottom of the device and, if so, remove it (Fig. 9).
• Insert the boiler into the device and hand-tighten the cover.
• Put the water tank back into the device.
• Store the hose, steam plates and power cable in the designated places (Fig. 10).
• To make it easier to stow the hose, there are markings on it for the correct winding radius.

Maintenance

• Grease the boiler and tank cap opening as well as the O-rings on the tank nozzle and pressure relief valve if necessary. (Fig. 11)
• Check the filter in the tank cap and clean it if necessary.

Important Note regarding Product Liability!

• In accordance with an EC directive, the manufacturer is liable for this product only if all parts originate from or were approved by the manufacturer and the tools are assembled and operated correctly.
• The use of other accessories and spare parts can partially or completely invalidate the liability.

Correction of Malfunctions

limescale

•  Malfunction (Descale and Refill flash and acoustic signal sounds)

**** •  Too little water in the tank. A safety cut-out is fitted to prevent overheating of elements if there is little water in the tank.

•  Unit at an angle, heating element is not in water.

•  Usage of an extension lead

**** •  Overpressure valve triggered (e.g. due to calcification or kinked/ clogged hose)

| •  Clean

•  Check the unit (tank, hose) for leaks. Check if the float is stuck. Check the heating element for scale build-up. Check/clean the filter in the tank cap.

•  Check the heating element and descale if necessary.

Fill with more water. Wait 2 minutes. Refill will reset the cut-out element.

•  Move the unit into a horizontal position.

•  Check that the extension lead is rated at a minimum of 13 Amps (230V)/ 16 Amps (110V) and fully unwound.

•  Let the device cool down and eliminate the cause (e.g. descale and clean hose)

Water in or under the device| •  Overpressure valve triggered (e.g. due to calcification or kinked/ clogged hose)

•  Boiler leaking

| •  Let the device cool down and eliminate the cause (e.g. descale and clean hose)

•  Replace

water

If the unit still will not operate return the unit to the dealer or authorised agent for investigation.

Technical Data

| 230 V version| 110 V version
---|---|---
Power source:| 230 V ~ 50Hz| 110 V ~ 50Hz
Power consumption:| 2750W (UK/EU)

2300W (AUS)

| 1760W
Max steaming time:*| 78 Minutes (UK)

95 Minutes (AUS)

| 129 Minutes
Steam rate:| 58 g/ min (UK) 47 g/ min (AUS)| 35 g/min
Max. filling volume:| 5.1L
Hose length:| 4.9 m
Unit weight:| 7.5kg
Max. weight load (one person only):| 150 kg

Approximate steam time before the safety cut-out operates.

Spare parts

Accessories

• Further information about the WAGNER range of products for decorative preparation is available at www.wagner-group.com.

Environmental protection

• The tool and all accessories and packaging have to be recycled in an environmentally friendly manner. Do not dispose of the tool with household waste.
• Support environmental protection by taking the tool to a local collection point or obtaining information from a specialist retailer.

WARNING (UK ONLY)

Mains Connection 230V

• Your unit has been supplied with a supply cord and a fitted plug. This is identified by the fuse holder in the base of the plug.
• Please read the following safety instructions before use.

1. If the fitted plug is cut off from the supply cord then the plug must be disposed of safely.
2. NEVER under any circumstances insert such a plug into a 13 Amp socket outlet.
3. NEVER under any circumstances use the appliance or supply cord without the fuse cover fitted. This is the little cover fixed into the base of the plug to hold the fuse in place.
4. If you lose the fuse cover then please contact any electrical dealer for a replacement or ring our helpline above.
5. A replacement fuse must be rated at 13 Amps and approved to BS1362.

IF IN ANY DOUBT PLEASE CONSULT A QUALIFIED ELECTRICIAN

• If you need to fit a plug to the supply cord, this should be fitted under the wiring instructions below and will need to be used with a 13 Amp fuse. If in doubt consult a qualified electrician.

EU Declaration of Conformity

• We declare under sole responsibility that this product conforms to the following relevant stipulations: 2014/35/EU, 2014/30/EU, 2011/65/EU, 2012/19/EU

Applied harmonized norms:

• EN 60335-1, EN 60335-2-54, EN IEC 55014-1, EN IEC 55014-2, EN IEC 61000-3-2,
• EN 61000-3-3, EN 62233
• The EU declaration of conformity is enclosed with the product.
• If required, it can be re-ordered using order number 2450631.

3 + 2-YEAR GUARANTEE ON THIS WAGNER CONTRACTOR PRODUCT (Status 03.03.2022)

• WAGNER exclusively provides the commercial buyer who has purchased the product from an authorized specialist dealer (hereinafter referred to as the „Customer“) with a guarantee for the products listed on the Internet at
• https://go.wagner-group.com/3plus2-info in addition to the statutory warranty regulations, unless there is a guarantee exclusion.
• The guarantee period for WAGNER products (devices) in the contractor‘s sector is 36 months and begins with the date of purchase of the initial purchase.
• This guarantee period is extended by a further 24 months if the product is registered within 28 days of purchase on the Internet at https://go.wagner-group.com/3plus2.
• In cases of commercial rental, industrial use (e.g. use in shift operation), or equivalent use, the guarantee period is 12 months due to the significantly higher load.
• We reserve the right to carry out a check in individual cases and refuse the guarantee where necessary.
• If any material, machining, or performance defects are identified in the device within the guarantee period, then the guarantee claims must be made immediately and within no more than 2 weeks following the discovery of the defect.
• The detailed guarantee conditions can be obtained on request from our authorized WAGNER partners (see website or operating instructions) or in text form on our website: https://go.wagner-group.com/pf-warranty-conditions .
• Subject to modifications

UKCA Declaration of Conformity

• We declare under sole responsibility that this product conforms to the following relevant regulations:
• Electrical Equipment (Safety) Regulations 2016
• Electromagnetic Compatibility Regulations 2016
• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
• The Waste Electrical and Electronic Equipment Regulations 2013 Applied harmonised standards
• BS EN 60335-1:2012+A15:2021, BS EN 60335-2-23:2003+A2:2015,
• BS EN IEC 55014-1:2021, BS EN IEC 55014-2:2021, BS EN IEC 61000-3-2:2019+A1:2021,
• BS EN 61000-3-3:2013+A2:2021, BS EN 62233:2008
• UK IMPORTER
• Wagner Spraytech (UK) Limited Innovation
• Centre Silverstone Park, Silverstone
• Northants NN12 8GX
• Great Britain
• Tel. 01327 368410enquiries@wagner-group.com
• Not responsible for errors and changes.
• Material No. 2436078 B 01/2024
• © Copyright by J.Wagner GmbH

Documents / Resources

| WAGNER SteamForce Speed Pro Wallpaper Steamer [pdf] User Guide
SteamForce Speed Pro Wallpaper Steamer, SteamForce, Speed Pro Wallpaper Steamer, Pro Wallpaper Steamer, Wallpaper Steamer, Steamer
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>