artika UCL-S2C-C1 LED Under-Cabinet LED Light Kit Instruction Manual

artika UCL-S2C-C1 LED Under-Cabinet LED Light Kit

INSTRUCTION MANUAL

IMPORTANT: READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.

INCLUDED

| Retaining screw Vis de fixation| x 6 + 3 extras
| Mounting plate Plaque de montage| x 6
| USB-C Power wire (450 mm / 18 in)

| x 2
| USB-C Power wire (910 mm / 36 in)|

x 2

****| Power supply| x 1

| ****

LED panel with motion sensor and tunable white technology

| x 1

| LED panel| x 2
**| Retaining screw for connection box Vis| x 2
**| Wire connector  de cable| x 3
**| Decorative caps  Tapas decorativas| x 2
**| Pre-assembled connection box| x 1

CAUTION Do not use a dimmer, it is integrated in the under- cabinet light fixture.

IMPORTANT …
The installer and/or user must read, understand and follow these instructions before installing the product. This product must be properly installed before it is used. If instructions are not followed, the manufacturer will not be held responsible for any problems or product malfunction. Failure to follow installation and/or operating instructions voids the warranty.
To reduce the risk of fire, electric shock, or injury to persons:

• Use only insulated staples or plastic ties to secure cords;
• Route and secure cords so that they will not be pinched or damaged when the cabinet is pushed to the wall;
•  Position the portable cabinet light with respect to the cabinet so the lamp replacement markings are able to be read during relamping;
• Not intended for recessed installation in ceilings, or soffits; and
•  The National Electrical Code (NEC) does not permit cords to be concealed where damage to insulation may go unnoticed. To prevent fire danger, do not run cord behind walls, ceilings, soffits, or cabinets where it may be inaccessible for examination. Cords should be visually examined periodically and immediately replaced when any damage is noted.

UNDERMOUNT INSTALLATION, SURFACE MOUNTING

OPTION 1: DIRECT PLUG-IN

1. Make sure to plug first into the power outlet the panel with the motion sensor. (fig. 1a)

2. Decide the location of the light panels before fixing your product. use a measuring tape to ensure that the distance between the LED panels does not exceed the length of the supplied connector wires (Fig. 1b). Make sure the first panel is near a power outlet.

3. Screw the mounting plates underneath your mounting surface and insert the light panel into place (fig. 2). Repeat this step for the other panels.
   

4. Connect the panels together (fig. 3) and connect the power supply unit to the first panel fitted with the motion detector (fig. 3a) then to the socket (Fig. 3a). Maximum 3 panels per power supply

5. Connect the power supply to the wall plug (fig. 3b).

6. Connect the other end of the power supply unit to the first luminous panel fitted with the motion detector and then to the power socket (fig. 3b). The power supply must be connected to the motion sensor side.
   

7. Switching on/off: Swipe the hand at a distance of about 5cm from the detector to turn on/off the light panels (fig. 4a).

8. Light intensity function: Keep your hand at a maximum distance of 5cm until the desired light intensity is reached. Remove hand to maintain the desired brightness. Repeat the operation to adapt / change the light intensity (fig. 4b).

9. Function Adjustable white technology: Press the white Preset: 3000K – 4000K – 5000
   

OPTION 2: HARDWIRE JUNCTION BOX

1. Remove the screws from the housing to open the small junction box (fig. 5a).
2.  Secure the junction box near the electrical wires using the fixing screws provided (fig. 5b).

3.  Pass the electric wires to the junction box through the grommet (fig. 6a).

4. Make the connections inside the junction box, connecting the white wire from the light fixture to the white wire from the junction box using a connection cap, the black wire from the fixture to the black wire from the junction box using a connection cap and connect the ground wire (G) from the light fixture to the ground wire (G) from the junction box using a wire connector then reinstall the grommet (fig. 6b).

5. Close the connection box with the screws (fig. 6c) then place the
   

6. Connect the power supply to the outlet on the junction box. (fig. 7).
   

Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

WARNING:
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device does not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
•  Increase the distance between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit that the receiver is not connected to.
•  Consult the dealer or an experienced radio/TV technician for help.

WARRANTY

Artika For Living Inc. is proud to offer you a three-year (3) limited warranty on manufacturing defects from the date of purchase for residential use only. The warranty is extended to the original owner in USA and Canada and is non- transferable. It does not apply to retailers, commercial applications or establishments. The original sales receipt is required for all warranty claims. The remedy under this limited warranty shall be product or part replacement at Artika’s discretion as provided herein and cannot exceed the original purchase price.
This warranty is valid only on products installed in accordance with the building code and laws effective in the region where the unit is used as well as in accordance with the provided instruction manual. It does not cover products installed incorrectly or subjected to abnormal use. Product(s) or component part(s) may be required to be returned for inspection and verification.
Normal wear and tear, misuse, negligence, vandalism, improper maintenance (surface damage due to chemical interaction or cleaning agents including, but not limited to, scouring pads, use of cleaners containing abrasives, alcohol or other organic solvents) improper handling, accident, abuse, fire, flood, theft, acts of God, neglect, or alteration of the product will not be covered under this limited warranty. It excludes any accessories that accompany the product including but not limited to bulbs or batteries. The warranty does not cover handling, labor, transportation, or any other
cost associated with the installation or replacement of the product. This limited warranty is valid in the country of purchase and by Artika authorized retailers only. Artika for Living Inc. will not be held responsible for any direct or consequential damages or injuries related to the use of this product arising from improper use or installation of this product. Please visit www.artika.com to discover more about Artika for Living Inc.

References

• Modern Lighting Fixtures | Best Online Lighting Store | Artika

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>