Shenzhen Eybond WIFIKIT02V50 Wi-Fi Kit Installation Guide
- June 6, 2024
- Shenzhen Eybond
Table of Contents
WIFIKIT02V50 Wi-Fi Kit
Installation Guide
2. Wireless Router Connection
2.1 Download APP
- Scan the QR Code from the cover of this guideline and download the APP.
- Open the APP, tap the Wi-Fi Config button to enter this page.
2.2 Connect Wi-Fi Datalogger
-
Tap the Connect Wi-Fi Datalogger button on the Connected page.
(Android phone has no need of this step) . -
Select the same number of Wi-Fi Mini PN to connect.
(Initial Password: 12345678)
2.3 Network Setting
- After the connection completes, tap the Network Setting button.
- According to the prompts, type in the information to finish the network setting.
- Reconnect the Wi-Fi or Cellular Data which can surf the Internet instead of the Wi-Fi connected by step 2.2.
3. Create Account And Plant
3.1 Create Account
- Open the APP, tap the Register button.
- According to the prompt information, complete creating an account
3.2 Create Plant
- Login the account and click the list button on the bottom of the home page.
- Tap the “+” button on the top-right corner of the list page.
- According to the prompts, type in the information to finish creating plant.
3.3 Add Multiple Dataloggers
Note: One account can create multiple plants and one plant can add multiple dataloggers. If you only have one datalogger, you can ignore this step.
- Tap the new plant you just created, and enter its home page.
- Click the Device button on the bottom of the home page.
- Tap the “+” button at the top-right corner to add the datalogger.
- Scan the datalogger PN on the Wi-Fi Mini, or input it manually.
Note: Besides the SmartClient APP, you’re also can remote monitoring your plants by using WeChat mini program.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance of 20cm the radiator
your body. This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter.
2.2 List of applicable FCC rules
List the FCC rules that are applicable to the modular transmitter. These are
the rules that specifically establish the bands of operation, the power,
spurious emissions, and operating fundamental frequencies.
DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B)
since that is not a condition
of a module grant that is extended to a host manufacturer. See also Section
2.10 below concerning the need to notify host manufacturers that further
testing is required.3
Explanation: This module meets the requirements of Part 15 Subpart C Section 15.247
2.3 Summarize the specific operational use conditions
Describe use conditions that are applicable to the modular transmitter,
including for example any limits on antennas, etc. For example, if point-to-
point antennas are used that require reduction in power or compensation for
cable loss, then this information must be in the instructions. If the use
condition limitations extend to professional users, then instructions must
state that this information also extends to the host manufacturer’s
instruction manual. In addition, certain information may also be needed, such
as peak gain per frequency band and minimum gain, specifically for master
devices in 5 GHz DFS bands.
Explanation: The EUT uses PCB Antenna, antenna gain: 1dBi. There is no restriction on the installation method.
2.4 Limited module procedures
If a modular transmitter is approved as a “limited module,” then the module
manufacturer is responsible for approving the host environment that the
limited module is used with. The manufacturer of a limited module must
describe, both in the filing and in the installation instructions, the
alternative means that the limited module manufacturer uses to verify that the
host meets the necessary requirements to satisfy the module limiting
conditions.
A limited module manufacturer has the flexibility to define its alternative
method to address the conditions that limit the initial approval, such as:
shielding, minimum signaling amplitude, buffered modulation/data inputs, or
power supply regulation. The alternative method could include that the limited
module manufacturer reviews detailed test data or host designs prior to giving
the host manufacturer approval.
This limited module procedure is also applicable for RF exposure evaluation
when it is necessary to demonstrate compliance in a specific host. The module
manufacturer must state how control of the product into which the modular
transmitter will be installed will be maintained such that full compliance of
the product is always ensured. For additional hosts other than the specific
host originally granted with a limited module, a Class II permissive change is
required on the module grant to register the additional host as a specific
host also approved with the module.
Explanation: The module is not a limited module
2.5 Trace antenna designs
For a modular transmitter with trace antenna designs, see the guidance in
Question 11 of KDB Publication 996369 D02 FAQ – Modules for Micro-Strip
Antennas and traces. The integration information shall include for the TCB
review the integration instructions for the following aspects: layout of trace
design, parts list (BOM), antenna, connectors, and isolation requirements.
a) Information that includes permitted variances (e.g., trace boundary limits,
thickness, length, width, shape(s), dielectric constant, and impedance as
applicable for each type of antenna);
b) Each design shall be considered a different type (e.g., antenna length in
multiple(s) of frequency, the wavelength, and antenna shape (traces in phase)
can affect antenna gain and must be considered);
c) The parameters shall be provided in a manner permitting host manufacturers
to design the printed circuit (PC) board layout;
d) Appropriate parts by manufacturer and specifications;
e) Test procedures for design verification; and
f) Production test procedures for ensuring compliance.
The module grantee shall provide a notice that any deviation(s) from the defined parameters of the antenna trace, as described by the instructions, require that the host product manufacturer must notify the module grantee that they wish to change the antenna trace design. In this case, a Class II permissive change application is required to be filed by the grantee, or the host manufacturer can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application.
Explanation: Yes. The module without trace antenna designs
2.6 RF exposure considerations
It is essential for module grantees to clearly and explicitly state the RF
exposure conditions that permit a host product manufacturer to use the module.
Two types of instructions are required for RF exposure information: (1) to the
host product manufacturer, to define the application conditions (mobile,
portable – xx cm from a person’s body); and (2) additional text needed for the
host product manufacturer to provide to end users in their end-product
manuals. If RF exposure statements and use conditions are not provided, then
the host product manufacturer is required to take responsibility of the module
through a change in FCC ID (new application).
Explanation: This module complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment. This module is designed to comply with
the FCC statement, FCC ID is: 2ASAF-WIFIKIT02V50
2.7 Antennas
A list of antennas included in the application for certification must be
provided in the instructions. For modular transmitters approved as limited
modules, all applicable professional installer instructions must be included
as part of the information to the host product manufacturer. The antenna list
shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that
for example an “omni-directional antenna” is not considered to be a specific
“antenna type”)).
For situations where the host product manufacturer is responsible for an
external connector, for example
with an RF pin and antenna trace design, the integration instructions shall
inform the installer that unique
antenna connector must be used on the Part 15 authorized transmitters used in
the host product. The module manufacturers shall provide a list of acceptable
unique connectors.
Explanation: The EUT uses PCB Antenna, antenna gain: 1dBi.
2.8 Label and compliance information
Grantees are responsible for the continued compliance of their modules to the
FCC rules. This includes advising host product manufacturers that they need to
provide a physical or e-label stating “Contains FCC
ID” with their finished product. See Guidelines for Labeling and User
Information for RF Devices –KDB Publication 784748.
Explanation: The host system using this module, should have label in a visible area indicated he following texts: “Contains FCC ID: 2ASAF- WIFIKIT02V50
2.9 Information on test modes and additional testing requirements5
Additional guidance for testing host products is given in KDB Publication
996369 D04 Module Integration Guide. Test modes should take into consideration
different operational conditions for a standalone
modular transmitter in a host, as well as for multiple simultaneously
transmitting modules or other transmitters in a host product.
The grantee should provide information on how to configure test modes for host
product evaluation for
different operational conditions for a stand-alone modular transmitter in a
host, versus with multiple, simultaneously transmitting modules or other
transmitters in a host.
Grantees can increase the utility of their modular transmitters by providing special means, modes, or instructions that simulates or characterizes a connection by enabling a transmitter. This can greatly simplify a host manufacturer’s determination that a module as installed in a host complies with FCC requirements.
Explanation: Data transfer module demo board can control the EUT work in RF test mode at spcified test channel
2.10 Additional testing, Part 15 Subpart B disclaimer
The grantee should include a statement that the modular transmitter is only
FCC authorized for the specific rule parts (i.e., FCC transmitter rules)
listed on the grant, and that the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the
modular transmitter grant of certification. If the grantee markets their
product as being Part 15 Subpart B compliant (when it also contains
unintentional-radiator digital circuity), then the grantee shall provide a
notice stating that the final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.
Explanation: The module without unintentional-radiator digital circuity, so the module does not require an evaluation by FCC Part 15 Subpart B. The host shoule be evaluated by the FCC Subpart B
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>