THINKWARE Q1000 Car Dash Cam User Guide
- June 5, 2024
- THINKWARE
Table of Contents
THINKWARE Q1000 Car Dash Cam
Before using the product
About the product
This product records videos while the vehicle is operating. Use this product
only for reference when investigating incidents or road accidents. This
product is not guaranteed to record for all events. The device may not record
accidents with impacts that are too minor to activate the impact sensor or
accidents with massive impacts that cause the vehicle’s battery voltage to
deviate.
Video recording does not begin until the product is completely turned on
(booted up). To ensure that all vehicle events are recorded, wait until the
product is completely booted up after turning it on, and then begin operating
the vehicle.
THINKWARE is not responsible for any loss caused by an accident, nor is it
responsible for providing any support regarding the outcome of an accident.
Depending on the vehicle’s configuration or operating conditions, such as the
installation of remote door lock devices, ECU settings, or TPMS settings, some
product features may not be supported, and different firmware versions may
influence the product’s performance or features.
About the user guide
The information provided in the guide may change when the manufacturer updates
its service policy.
This user guide is intended for the THINKWARE Q1000 model only, and it may
contain technical errors, editorial errors, or missing information.
Copyrights
All rights for the content and maps in this guide are reserved by THINKWARE
and are protected under copyright laws. All unauthorized duplication,
revision, publication, or distribution of this guide without written consent
from THINKWARE is prohibited and is eligible for criminal charges.
Registered trademarks
THINKWARE Q1000 is a registered trademark of THINKWARE.
Other product logos and service names in this guide are trademarks of the
relevant companies.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter.
- A minimum separation distance of 20cm must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements.
Information to user : RSS-247 This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Please be cautioned the changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Notice: Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Antennas Statement
This radio transmitter (identify the device by certification number or model
number if Category II) has been approved by Industry Canada to operate with
the antenna types listed below with the maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with
this device.
Safety information
Read the following safety information to properly use the product.
Safety symbols in this guide
“Warning” – Indicates a potential hazard which, if not avoided, may result in injury or death.”Caution” – Indicates a potential hazard which, if not avoided, may result in minor injury or property damage.”Note” – Provides useful information to help users better utilize the product’s features.
Safety information for proper use
Driving and product operation
- Do not operate the product while driving a vehicle. Distraction while driving may cause accidents and result in injury or death.
- Install the product in places where the driver’s view is not obstructed. Obstruction of the driver’s vision may cause accidents and result in injury or death. Check with your state and municipal laws before mounting the product to the windshield.
Power supply
- Do not operate or handle the power cable with wet hands. Doing so may result in electrocution.
- Do not use damaged power cables. Doing so may result in electrical fire or electrocution.
- Keep the power cable away from all heat sources. Failure to do so may cause the power cord insulation to melt, resulting in electrical fire or electrocution.
- Use the power cable with the correct connector and make sure the power cable is connected securely and is firmly in place. Failure to do so may result in electrical fire or electrocution.
- Do not modify or cut the power cable. Also, do not place heavy objects on the power cable or pull, insert, or bend the power cable using excessive force. Doing so may result in electrical fire or electrocution.
- Use only genuine accessories from THINKWARE or an authorized THINKWARE dealer. THINKWARE does not guarantee compatibility and normal operation of third-party accessories.
- When connecting the power cable to the product, ensure that the connection between the cable plug and the power cable connector on the product is secure. If the connection is loose, the power cable may become disconnected due to vehicle vibration. Video recording is not available if the power connector is disconnected.
Children and pets
Ensure that the product is out of the reach of children and pets. If the product breaks, it may result in fatal damage.
Other information about the product
Product management and operation
- Do not separate the product and the mount when the product is turned on. Doing so may result in product malfunction.
- Do not expose the product to direct sunlight or intense light. The lens or internal circuitry may fail otherwise.
- Use the product at a temperature between 14°F and 140°F (-10°C to 60°C) and store the product at a temperature between -4°F and 158°F (-20°C to 70°C). The product may not function as designed and some permanent physical damages may result if it is operated or stored out of the specified temperature ranges. Such damages are not covered by the warranty.
- Frequently check the product for the proper installation position. Impact caused by extreme road conditions may alter the installation position. Ensure that the product is positioned as instructed in this guide.
- Do not apply excessive force when pressing the buttons. Doing so may damage the buttons.
- Do not use chemical cleaners or solvents to clean the product. Doing so may damage plastic components of the product. Clean the product using a clean, soft, and dry fabric.
- Do not disassemble the product or subject the product to impact. Doing so may damage the product. Unauthorized disassembly of the product voids the product warranty.
- Handle with care. If you drop, mishandle, or expose the product to external shocks, it may cause damage and/or result in the malfunction of the product.
- Do not attempt to insert foreign objects into the device. Doing so may damage the product.
- Avoid excessive humidity and do not allow any water to enter the product. Electronic components inside the product may fail if exposed to humidity or water.
- Depending on the make and model of your car, the power may be constantly supplied to the dash cam even when the ignition is turned off. Installation of the device to a continuously powered 12V outlet could result in vehicle battery drainage.
- This device is designed to record video while the vehicle is in operation. The quality of the video might be affected by weather conditions and the road environment, such as whether it is day or night, presence of street lighting, entering/exiting tunnels, and the surrounding temperature.
- THINKWARE is NOT responsible for the loss of any recorded video during operation.
- Although the device was designed to withstand high-impact car collisions, THINKWARE does not guarantee the recording of accidents when the device is damaged as a result of the accident.
- Keep the windshield and camera lens clean for optimal video quality. Particles and substances on the camera lens or windshield may reduce the quality of the recorded videos.
- This device is intended to be used inside the vehicle only.
Product overview
Included items
Ensure that all the items are included when you open the product box.
Standard items
**Accessories (sold separately)
**
Part names
Front camera (main unit) – front view
Front camera (main unit) – rear view
Rear camera (optional)
Removing and inserting the memory card
Follow the instructions to remove the memory card from the product or to
insert the memory card into the product.
Before removing the memory card, ensure that the product is turned off. Gently
push the bottom of the memory card with your fingernail to release it, and
then remove it from the product.
To insert the memory card into the memory card slot, ensure that the metal
contacts on the memory card are facing toward the product’s buttons, and
insert it into the slot until you hear a click.
- Ensure that the product is turned off before removing the memory card. The recorded video files may be corrupted or lost if you remove the memory card while the product is on.
- Ensure that the memory card is in the correct direction before inserting it into the product. The memory card slot or the memory card may be damaged if it is inserted incorrectly.
- Use only authentic memory cards from THINKWARE. THINKWARE does not guarantee the compatibility and normal operation of third-party memory cards.
Installing the product
Installing the front camera (main unit)
Follow the instructions to properly install the product.
Selecting an installation location
Select an installation location that can record the entire view in front of
the vehicle without obstructing the driver’s vision. Ensure that the front
camera lens is located in the center of the windshield.
Securing the product
Follow the instructions to secure the product at the installation location.
- Align the mount to the mounting rail on the product, and then slide it until you hear a click (➊➊). Then, carefully remove the protective film (➋➋).
- 2 After determining the installation location, wipe the installation location on the windshield with a dry cloth.
- Attach the shield film to the installation location.
- Remove the protective film from the adhesive mount, and then press the mount to the shield film.
- Remove the product from the mount and push the mount against the windshield to ensure that the mount is firmly fixed.
- Align the product to the mount, and then slide it into the locking position until you hear a click.
- Set the vertical angle of the camera appropriately.
Connecting the power cable
When the engine and electrical accessories are turned off, connect the car
charger.
Connect the car charger to the product’s DC-IN power port and insert the cigar
jack into the vehicle’s power socket.
Connect the product to the THINKWARE DASH CAM LINK on your smartphone and
adjust the camera angle so that the hood of the vehicle covers 1/4 – 1/8 of
the screen while viewing the live view screen, as shown in the image to the
left.
For more information about connecting and using the THINKWARE DASH CAM LINK,
refer to “4. Using the mobile viewer” on page 24.
Installing the rear camera (optional)
Refer to the following instructions to properly install the rear camera.
Selecting an installation location
- Select a location on the rear windshield where there is no defrost grid wire and the camera can record the entire rear view.
Securing the rear camera
Refer to the following instructions to secure the product to the installation location.
- 1 After determining the installation location, wipe the installation surface of the windshield with a dry
- Remove the protective film from the adhesive mount and camera lens.
- Attach the product with the THINKWARE logo facing indoors and press the adhesive tape firmly to secure the camera.
- Adjust the camera’s vertical angle.
Connecting the rear camera cable
Power off the product and connect the rear camera cable to the front camera (main unit).
- 1 Connect one end of the rear camera cable to the front camera’s V-IN port.
- Connect the other end of the rear camera cable to the rear camera’s connection port.
- Turn on the ACC or start the engine to check if the product is powered on. After the product is powered on, the voice guidance will be turned on.
Installing the RADAR module (optional)
Refer to the following instructions to properly install the RADAR module. Install the RADAR module near the product, taking the module’s cable length into account.
- Remove the film on the back of the RADAR module.
- Attach the RADAR module’s adhesive surface to the upper part of the front windshield and press the adhesive part firmly to secure it.
- Connect the RADAR module to the product’s RADAR connector.
- Turn on the ACC or start the engine to check that the product is powered on. After the product is powered on, the REC LED and the voice guide are turned on.
Using recording features
Turning the product on or off
The product is turned on automatically and continuous recording starts when
you turn on the ACC or start the engine.
Learning about the file storage locations
Videos are stored in the following folders according to their recording mode.
On the mobile viewer| Continuous| Continuous Incident| Manual Recording| Motion Detection| Parking Incident| SOS
Recording
---|---|---|---|---|---|---
In the memory card| cont_rec| evt_rec| manualrec| motion timelapse_rec|
parking_rec| SOS_rec
Using the continuous recording feature
Connect the power cable to the product’s DC-IN power port and then turn on the
vehicle’s electrical accessories or start the engine. The voice guide will
indicate that continuous recording has started.
During continuous recording, the product operates as follows.
| Mode | Operation description | REC LED |
|---|---|---|
| Continuous recording | During driving, videos are recorded in 1 minute segments |
and stored in the
“cont_rec” folder.
|
(light on)
Incident continuous recording*| When an impact to the vehicle is detected, a video is recorded for
20 seconds (from 10 seconds before the detection to 10 seconds after the detection) and stored in the “evt_rec” folder.
|
(flickers)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>