Langshixing Electronic QB320 Intelligent PTZ Camera User Manual
- June 5, 2024
- Langshixing Electronic
Table of Contents
Langshixing Electronic QB320 Intelligent PTZ Camera
Instruction
Packing list
Product structure-front
Content
Indicator light
Description
- Sbw flashing green light Device running/ preview image
- The green light is always on Device networking
- Sbw flashing of red ight Device waiting in distribution network
- Red light flash Device in /offline distribution network
Product structure-back
Content
- RESET
- TF card slot
Description
- Press the reset button for 3~5 seconds to restore the factory settings
- Support TF card bcal storage (maximum 128G). If you insert a TF card for the first time, please format it first
Download the App
Scan the below QR code or search the “CloudEdge” in the APP store or google play, then download and install the APP.
User Sign Up, Log in
- Sign Up : Select your country to register an account with your email.
- Log in: Select your country, enter the existing account and password to log in.
Add the Camera
Make sure the wifi for phone connection is 2.4G and in the good network condition (5GHz not supported) ,wait for the device red indicator flickers slowly (if the device red indicator doesnt flickers slowly, long press the reset for 3-5s until the device send out “BUGU sound ,wait for the device to restart then add the camera). Open the “CloudEdge APP, click icon in the upper right corner to add the camera, select Camera ,then enter the camera list screen. Follow the app prompt click “Nex- t”,enter wi-fi password which mobile phone connected,then click “Next then put the QR code face to the camera about 10 to 15 cm, waiting for the camera emits BUGU” sound ,then click “Next”, then the APP will search the device automatically.
Function introduction
- Time of the device
- 8 Full screen preview
- Sound of the device Definition of the picture
- History
- O Cloud
- Live
- Screenshot
- PTZ
- 2 Record
- Motion Detection
- Intercom
- Settings
- 19 Album
FAQ
-
Q: Failed to add during network configuration?
A: Please make sure your phone is connected to a router in the 2.4GHz band, and make sure that the WI-Fi password is correct. -
Q: After scan adding is still unsuccesstul?
A: Hestart the device or power oft the device after scan adding is still unsuccesstul, and then try to add it again. -
Q: The device cannot preview normally?
A: Please check it the network signal is too eak, please put the camera close to the router, it still cannot preview, reset the camera and add it again. -
Q: After resetting the device, why is the camera still in the device list?
A: Resetting the device only to reset the camera s network configuration, but cannot change the configuration on the APP, too delete the camera, you must log in the APP to delete. -
Q: How to switch the camera network to another router?
A: First remove and reset the device on the APP, and then configure the network for the device again through the APP. -
Q: Why does the device can not recognize the TF card?
A: Please insert and remove the TF card after power ott, please check if the TF card is working normally and whether it is in FAl32 format, when the mobile phone or the device is working in unstable network, the APP also will prompt that the TF card cannot be recognized.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following TwO conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation, This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there Is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment ofr and on, the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver, Connect the equipment into an outet on a circuit different from that to which the receiver is connected, and Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>