KRIEG KD332 UHF Digital Wireless Microphone User Manual

KRIEG KD332 UHF Digital Wireless Microphone User Manual

I. BRIEF INTRODUCTION

Wireless microphone system is very easy to install and convenient to use, the first choose for singers. This model adopts intelligent cryptographic hardware, to achieve unique sound and RF performance. Frequencies group, colourful TFT display and humanized menu make it easy for single or multi-sets installation.

II.MAIN FEATURES

• Optional UHF band 660-690 MHz
• Unique digital 16 bit ID pilot technology, no crosstalk disturbance even in same frequency;
• Ultra-short audio latency
• Audio sampling mode: 48K
• Frequency response: 30-20KHz
• Receiver use colourful TFT display and menu settings
• Auto frequency scanning and frequency spectrum display
• Built-in echo, EQ, function

III. PARTS(RECE IVER)

1. POWER
2. SETUP A
3. IR
4. UNLOCK
5. TFT WINDOW
6. IR
7. TFT WINDOW
8. IR
9. UNLOCK
10. SETUP B
11. ANT-A
12. ANT-B
13. MIX.OUT
14. BALANCE A
15. BALANCE B
16. DC INPUT
17. USB CHARGE OUTPUT

IV.RECEIVER SCREEN

GR/CH: GR: Group: Indicate the current frequency group.
CH: Channel: Indicate the current frequency channel.

SCAN: Auto scan. Automatically scan up or down to search for available frequency until the desired frequency is reached can be set under SCAN function.

EFFECT: Audio Effect Setting menu and condition.

Display function operation

When the receiver working, long press UNLOCK to un-locked the system before setting. Initial setup from channel adjustment, below is the operation of the product.

Note: the below setting is under unlock status, long press UNLOCK before setting.

• Channel setting mode

• Scan available channels mode

• EFFECT SETTING

V.HANDHELD MIC OPERATION

1. Microphone Capsule: pick up sound.
2. LCD: indicates microphone working status.
3. ON/OFF Switch: control handheld microphone to be power on, off and mute.
4. IR Window: SYNC IR signal with receiverlR window.
5. Battery Sink: insert 1 X 18500 lithium battery with correct direction.
6. Mic Cap: unscrew it when change batteries.

► HANDHELD LCD

• Open battery cover, insert 1 X 18500 lithium battery with correct direction.
• Check batteries direction or status if LCD is not bright after long pressing switch for 3 seconds. Batteries need to be changed in low condition, when battery symbol flashing on LCD.
• Device works properly only if hand held and receiver are in same frequency.
• Hand held is in default mode when switched on and the frequency is the same as last used. Re-SYNC with receiver is necessary when change any setting.

NOTE: IR SYNC function is available only within 30 seconds after booting up hand held.

► Handheld Microphone Holding Ways

• Keep distance of mouth and mic head less than 15CM.
• Avoid using mic head to point to speakers.

VI.SAXOPHONE WIRELESS TRANSMITTER

1. Capsule
2. Nail
3. Audio input
4. attenuation switch
5. IRwindow
6. Indicator light
7. Power switch
8. Rechargeable port
9. Antenna
10. Saxophone Clamp

VII.BODYPACK OPERATION

1. Bodypack Clamp
2. Audio input
3. attenuation switch
4. IRwindow
5. Indicator light
6. Power switch
7. Rechargeable port
8. Antenna

► AUDIO INPUT
Support to connect extra wired microphone or sound source equipment.
For example, lapel mic, headset mic, MP3, mobile phone and so on.

VIII.RECEIVER OPERATION

• Pull out antennas(11) (12) and keep their angle 90° with receiver.

• Power supply connection:
  Connect power supply with DC input(16), make sure local power supply matches the item needed.

• Audio output connection:
  MIX output: connect one end of the attached audio cable into OUT. MIX port (13), meanwhile connect the other end into MIX IN or AUX IN port of mixer or speaker.

• Balance output: connect the audio cable(attached) to the MIX. OUT socket (14/15) while other side connect to MIX. IN or AUX. In socket of the audio mixer or power amplifier.

• Connect the USB charge cable Connect the charge cable (attached} to USB socket (17) while other side connect to the saxophone/hand held microphone

• Turn on the power button (1), TFT screen (5/7) is lighting, receiver is in working statue.
  Note: Before turn on the receiver, turn the volume control knob (2/10) to the minimum volume, adjust the volume as needed when the receiver is working.

• Select function by adjusting the SET UP knob (2/10) (Function details refer to the instruction of receiver TFT LCD display function)

• See below IR SYNC picture, long press IR button under unlock status, receiver start sending signal, automatically turn to work after completion.

SNYC IR operation shows as above picture. Boot up receiver, and then long press IR button for 3 seconds till the IR indicator flashing and transmit IR signal, meanwhile, boot up microphone and keep ts IR window close to receiver’s. Same frequency will show on microphone and receiver at the same time when IR SNYC successfully, and RF signal will show on LDC on receiver.

IX.TECHNICAL SPECIFICATION RECEIVER

• Carrier Frequency: UHF 660-690 MHz
• Bandwidth: 12.5MHz
• Channel Bandwidth: 300KHz
• Dynamic Range: 96dB
• Distortion: <0.1 %
• Frequency Response: 30-20KHz/±2dB
• Signal/ Noise Ratio: 96dB
• Receiving Sensitivity: <3ms
• Power Supply: DC12~18V 1 A
• Audio Output: 1x 6.3mm, 2x XLR balance output

BODYPACK TRANSMITTER optional

• Carrier Frequency: UHF 660-690 MHz, optional
• Bandwidth: 12.5MHz
• Frequency Switch: IR SYNC
• Output Power: 1 0mW
• Harmonic Radiation: <-50 dBc
• Battery: 2X1 .SVAA battery
• Battery Life: >5h

HANDHELD TRANSMITTER/SAXOPHONE optional

• Carrier Frequency: UHF 660-690 MHz, optional
• Bandwidth: 12.5MHz
• Frequency Switch: IR SYNC
• Output Power: 1 0mW
• Harmonic Radiation: <-50 dBc
• Battery: Built-in lithium battery
• Battery Life: >5h

WARNING
ANNOUNCMENTS

• Do place receiver in open space, so that it can receive signal better;
• Do not throw the device;
• Do not place device under rain or drop it into water;
• Keep device away from sunshine or electromagnetic field;
• Do insert batteries in right way, and remove them if device is idle for long time;
• Cut off power supply before battery replacement;
• Pull out power adaptor from power supply if receiver is idle for long time;
• Do not take apart device without permission, in case users are injured;
• Device doesn’t contain any part for self refitting, otherwise, warranty will be void;
• Use soft cloth to clean device, if there’s any stubborn stain, clean it with neutral detergent but not volatile gasoline or thinner;
• Keep at least 30CM space around device for better ventilating;
• Do not cover ventilation hole with paper, tablecloth or curtain;
• Do not put fire on device like burning candle;
• Keep device away from water drops, or any container with liquid like vase;
• Do not use new and old batteries at the same time, besides, replace them with same kind batteries; Discarding batteries to specific recycling bin;
• Working temperature: 5’C- 60’C;
• Please try below methods to solve interfered problem when using wireless microphones
•  Adjust place or direction of the antenna;
• Keep away from radio or TV;
• Do not plug in same electrical socket outlet with radio or TV;
• The best angle is 45’C for mouth and microphone when speech, in order to reduce affected by airflow from mouth;
• Using 1 microphone when 1 sound input, otherwise sound will be mixed;
• Keep distance of mouth and microphone less than 15CM because of cardioid pickup, otherwise bass is not good;

COPYRIGHT:
All Right Reserved.

www.krieg.mx

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>