Xpelair XPP Tower Fan with Remote Control Instruction Manual
- June 5, 2024
- Xpelair
Table of Contents
Important Safety Advice
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR
FUTURE REFERENCE
WARNING: To avoid the danger of suffocation please remove all packaging
materials, particularly plastic and EPS and keep these away from vulnerable
people, children, and babies.
DO NOT use this appliance in the immediate surroundings of a bath, a
shower, or a swimming pool.
DO NOT use this appliance if it has been dropped.
DO NOT use if there are visible signs of damage to the appliance. Use
this appliance on a horizontal and stable surface with the base securely
fitted.
DO NOT use this appliance until the base is properly assembled and it is
standing upright supported on and by its base only. Do not use lying down or
lying at an angle against anything. Only use the appliance on a stable and
level surface.
IMPORTANT: Electric appliances may only be repaired by qualified
personnel, improper work can be a source of considerable danger for the users.
If the mains lead of this appliance is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person in order to
avoid a hazard. This appliance can be used by children aged 8 years and above
and persons with reduced physical, sensory or mental capabilities or lack of
experience or knowledge if they have been given supervision or instruction
concerning the use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
WARNING: To avoid the risk of accidental strangulation from the supply
cord all children and vulnerable people must be supervised when in the
vicinity of the product whether it is working or not. The socket-outlet must
be accessible at all times to enable the mains plug to be disconnected as
quickly as possible.
CHOKING HAZARD: The remote control for this unit contains a small
battery. To avoid the risk of choking, keep the remote away from children and
do not swallow the battery. If the battery is swallowed seek medical advice at
once.
WARNING: Keep batteries out of reach of children, and dispose of used
button batteries immediately and safely.
DO NOT pull, carry or move the appliance using the power cable.
IMPORTANT : Disconnect the appliance from mains power whenever it is not
in use and before moving or relocating it.
IMPO0RTANT: To unplug the appliance do not pull on the mains cable, grip
the plug at the wall and pull carefully.
NEVER immerse the appliance in water or other liquids; never spray
liquids on the appliance.
NEVER operate the appliance if a cable or connector has been damaged,
after the appliance has malfunctioned or if the appliance was dropped or
otherwise damaged in any way.
DO NOT operate the appliance at any voltage other than that specified on
the rating label.
WARNING: To avoid the risk of damage or a dangerous situation do not use
this appliance or position any part of it near to heat, open flame, cooking
appliances or any heating appliance.
DO NOT use the appliance in an area where there are likely to be
flammable or explosive fumes or liquids.
DO NOT place any heavy objects on the appliance or any object against the
product when operating.
IMPORTANT: Should the appliance fail to operate please check the fuse in
the plug is intact and confirm that the circuit breaker/fuse at your
distribution board is operating before contracting the manufacturer or service
agent.
IMPORTANT: Only use the appliance inside (indoors) and only for the
purpose it was designed.
IMPORTANT: Unplug the appliance before cleaning. This instruction leaflet
belongs to the appliance and must be kept in a safe place. If changing owners,
the leaflet must be surrendered to the new owner.
How to assemble the base
Carefully remove the split base and the tower fan from its packaging.
Pass the power cord between the center of the two halves split the base and
fit the two halves together by lining the overlap bosses on the bottom (with
cable exit) with their pockets on the other half dropping into place and
pressing together.
Bring the assembled base up to the bottom of the tower and line up the small
pillar on the top of the raised center of the base with the matching hole in
the base socket location of the tower fan, pull the cable through fully so it
doesn’t interfere with the fitting together.
Take the 4 large screws provided and pass them through the holes in the
circular bosses (located around the central hub on the underside of the base)
into the bottom of the tower, screw fix them firmly in place.
Carefully fit the cable through the slot to the backside of the hub and then
through the guide location channel at the outside of the circular base to exit
level with the base through the channel at the back. The XPP Cooling fan is
now ready to stand and operate.
THIS IS NOT A FAULT
If the fan speed varies randomly including stopping and starting automatically
you have selected either NATURAL or NIGHTIME Variable Blower Mode which
simulates different breezy conditions. To de-select this mode you must press
the button to change back to constant blowing mode, please refer to section
‘d’ following on how to change modes. To run in constant speed mode only use
the button to select the speed you require, please refer to section ‘b’
following.
Operating Instructions
The LED display screen on the control panel of the product illuminates to
display the function you have selected when the fan is operating.
a. Turning on/off the fan: Gently press the “Standby” button on the soft-
touch button control panel or the wireless remote control.
b. Adjusting and Selecting Speed: 3 content speeds can be selected by
pressing the button either on the control panel or on the remote. Each time
you press this button the speed will cycle from I to II to III and back to
‘I’ again. Where “I” = Low Speed, “II” = Medium Speed, and “ III”
= High Speed.
c. Oscillating function: The product oscillates in an arc from left to
right and back again continuously thus circulating the airflow over a wider
area. To start the tower fan oscillating simply press the oscillating button
on the control panel for less than 2 seconds or the button on the remote and
the symbol will light up on the control panel. Press this button a second time
to stop the oscillating.
d. Variable Blower Function Selection: The product can be set to
automatically vary the speed output to simulate different breezy conditions.
It will normally run in constant blowing mode at whichever speed you selected
(see “b.” above). To select a variable blower speed function you can simply
press the button on the remote or press and hold the dual control button on
the control panel for at least 2 seconds. There are two selections available:
- The first mode activated will be the ‘natural breeze’ selection and the symbol will light up on the control panel. In this mode, the fan speed will continuously and randomly vary between speed levels (including off) to simulate variable wind conditions.
- Pressing the on the remote a second time or pressing and holding the dual control button on the control panel again for at least 2 seconds activates ‘night time’ selection and the symbol will light up on the control panel. In this mode, the fan speed varies automatically between speed levels (including off) at a less noticeable rate than the ‘natural breeze’ selection.
– Pressing the button a third time for more than 2 seconds will change it back to constant normal blowing mode.
e. Runback Timer function: The product can be set to switch off
automatically after running for one of the four user-selectable runback
periods i.e. 1 hr, 2 hr, 4 hr, or 8 hr.
To activate the runback function just simply press the timer button
- Press once and the timer is set to 1hr runback
- Press twice and the timer is set to 2hr runback
- Press 3 times and the timer is set to 4hrs runback
- Press 4 times and the timer is set to 8 hrs runback
- Press a 5th time and the timer function is switched off.
Remote Control
The remote control comes complete with a CR2025 3V battery fitted. To replace the battery simply remove the securing screw, unclip and remove the battery cover on the back and replace the battery, then carefully refit the cover on the back and replace the battery, then carefully refit the cover, snap into place and refit the securing screw.
Technical Specification
Specification Details – XPP | Symbol | Value | Unit |
---|---|---|---|
Maximum Fan Flow Rate | F | 9. | m3/min |
Fan Power Input | P | 32. | W |
Service Value | SV | 0.3 | (m3/min)/W |
Standby Power Consumption | PSB | 0.64 | W |
Fan Sound Power Level | LAW | 64 | dB(A) |
Maximum Air Velocity | c | 4. | meters/sec |
Rated Voltage | V | 220-240 | V |
Rated Frequency | Hz | 50 | Hz |
Measurement Standard for Service Value | I EC 60879:1986 |
Cleaning
WARNING ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE
APPLIANCE
The fan should be cleaned at least once every two months as dust may
accumulate on the grill cover which would affect performance. Do not use
detergents, abrasive cleaning
products or polish of any kind on the appliance. Wipe with a dry cloth to
remove dust and a damp cloth (not wet) to clean off stains. Be careful not to
allow moisture into the
appliance. Use a vacuum cleaner to remove any fluff which does accumulate.
Recycling
For electrical products sold within the European Community. At the end of the electrical product’s useful life, it should not be disposed of within household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice in your country.
Guarantee
What does an Xpelair Guarantee cover?
Xpelair products deliver reliable service for normal, household use in
domestic settings. All Xpelair products are individually tested before leaving
the factory. If you are a consumer and you experience a problem with your
Xpelair product, which is found to be defective due to faulty materials or
workmanship within the guarantee period, this Xpelair guarantee will cover
repair or – at the discretion of Xpelair – replacement with a functionally
equivalent Xpelair product. Your product is under guarantee for 1 year from
the date of purchase or the date of delivery of the product, if later. The
Xpelair guarantee is conditional upon you providing the original purchase
receipt as proof of purchase. Please, therefore, retain your receipt as proof
of purchase. If you do experience a problem with your Xpelair product please
call the Helpline on +44 [0]344 879 3588 or visit
https://www.xpelair.co.uk/support. For ROI please email
serviceireland@glendimplex.com or
call +353(0)1 842 4833. We will need details of your Xpelair product and a
description of the fault which has occurred. Once we receive your information
and proof of purchase we will contact you to make the necessary arrangements.
If your Xpelair product is not covered by this Xpelair guarantee there may be
a charge to repair your product. However, we will contact you for agreement to
any charges before any chargeable service is carried out.
What is not covered by an Xpelair Guarantee?
The Xpelair guarantee does not cover any of the following: Any fault or damage
to your Xpelair product due to faulty materials or workmanship occurring
outside the guarantee period. Normal wear and tear including parts that might
wear out over time or consumables, such as filters. Any fault or damage
occurring to any pre-owned Xpelair product or to any other equipment or
property. Accidental damage to your Xpelair product or damage to your Xpelair
product from external sources (for example, transit, weather, electrical
outages or power surges). Fault or damage to your Xpelair product is: Not due
to faulty materials or workmanship or which is due to circumstances outside
Xpelair’s control. Caused by the use of your Xpelair product for anything
other than normal domestic household purposes in the country where it was
purchased. Caused by any misuse, abuse or negligent use of the Xpelair
product, including but not limited to any failure to use it in accordance with
the Operating Instructions supplied with the product. Caused by any failure to
assemble, install clean, and maintain your Xpelair product in accordance with
the Operating Instructions supplied with the product unless this was carried
out by Xpelair or its authorized dealers. Caused by repairs or alterations to
your Xpelair product not carried out by Xpelair service personnel or its
authorized dealer(s). Caused by use of any consumables or spare parts for your
Xpelair product that is not Xpelair specified.
Terms and Conditions
The Xpelair guarantee is valid for 1 calendar year, from the date of purchase
of your Xpelair product from a recognized retailer in the country of purchase
and use, or the date of delivery of the product if later, always provided the
original receipt has been retained and is produced as proof of purchase. You
must provide to Xpelair or its authorized agents on request the original
receipt as proof of purchase and – if required by Xpelair – proof of delivery.
If you are unable to provide this documentation, you will be required to pay
for any repair work required. Any repair work under the Xpelair guarantee will
be carried out by Xpelair or its authorized dealer(s) and any parts that are
replaced will become the property of Xpelair. Any repairs performed under the
Xpelair guarantee will not extend the guarantee period. Any replacement of
your Xpelair product by Xpelair during the guarantee period will start the 1
year guarantee period afresh from the date of delivery of the replacement
Xpelair product to you. (*Please keep your original sales receipt as proof of
purchase). The Xpelair guarantee does not entitle you to the recovery of any
indirect or consequential loss or damage including but not limited to loss or
damage to any other property. The Xpelair guarantee is in addition to your
statutory rights as a consumer and your statutory rights are not affected by
this Xpelair guarantee.
Contact Xpelair A brand of Glen Dimplex UK Limited, trading as Dimplex
Dimplex Heating & Ventilation If you have any questions about what the Xpelair
Guarantee covers and does not cover or how to claim under the Xpelair
Guarantee, please contact us: Glen Dimplex Heating & Ventilation, Grange
Drive, Hedge End, Southampton SO30 2DF Telephone: 0344 879 3588 Visit:
www.xpelair.co.uk
This product complies with all the required European and UK Product Safety,
Electromagnetic Compatibility and
Environmental Standards. They are fully compliant with the LVD, EMC, RoHS and
Eco Design Directives and Regulations.
[c] Glen Dimplex.
All rights reserved. Material contained in this publication may not be
reproduced in whole or in part, without prior permission in writing of Glen
Dimplex.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>