RehabMart WB035A Wireless Door Chime User Manual
- June 5, 2024
- RehabMart
Table of Contents
RehabMart WB035A Wireless Door Chime
Quick Start
- Insert supplied battery into push button (transmitter).
- Plug chime receiver into standard 120 volt wall outlet.
- Hold button where you would like to mount it and push button to test location prior to mounting.
Installation
- Open the chime push button case by inserting a small screwdriver into the notch on the bottom and push to open.
- Insert the supplied 3V CR2032 battery into the button. The positive(+) side goes up.
- Plug the chime receiver into a 120V AC wall outlet.
- Make sure you test the operation, location, and distance of the transmitter and receiver prior to permanently mounting it.
Locate a good position for the push button next to the door (do not mount on or right next to a metal surface.) If mounting on a metallic or concrete surface, use a 1/8″ or ¼” wood spacer between the back of the button and the surface to increase the range. Wireless chime range may vary from 20 to 120 feet depending on the construction of your home or office. Wood or vinyl siding are ideal. Steel, aluminum, brick,’ or stucco will decrease the maximum operating range the system. To mount the push button: Drill two 4.76mm holes and insert the wall plugs. Place the back plate in the right position and tighten the plate on wall with the screws (2.6 x 26mm) supplied. Close the cover.
Operation
Press “Learn” button ( symbol – once (located on the side of receiver.) Two beeps indicates the receiver is in learning mode. Press the transmitter once, and you will hear the chime receiver sound. This indicates the receiver is coded with the transmitter correctly. Press the transmitter button to hear the receiver play the built-in tunes. Once you hear the desired melody, stop pressing the transmitter. There are total 3 different chime tunes for selection:
- ding ding
- ding dong
- Westminster chime
After you have chosen the desired tune, press the “learn” button again on the
receiver. The receive will sound 2 beeps to exit learning mode. *The receiver
will auto exit learning mode after 20 seconds if you do not manually exit
learning mode. Press the transmitter push button and the receiver will sound
the tune selected, and then flash the strobe light. The receiver can learn up
to 4 different transmitters. Repeat the steps outlined in
“Operation” above to train each transmitter to the receiver.
To erase all all learned transmitters, press & hold the “learn” button on the
receiver approximaiely 15secs until it sounds 4 beeps. It indicates all
learned transmitters have been erased successfully.
Troubleshooting
The range of the door chime depends on location, temperature and battery condition. If you are having problems with this product, please try the solutions listed below.
Chime doesn’t sound:
- Make the push button is trained to the receiver.
- Replace the button battery.
- Make sure there is electricity to the outlet the chime is plugged into.
Batteries are OK, but chime does not work when installed:
- Mounting the chime or button directly on metal, concrete or hear metal studs reduces the range. Use ¼” to ½” wood shims to move the chime or doorbell button off of the surface.
- Do not mount the chime too close to ground level concrete slabs, which may reduce the range. Mount the chime away from the floor
- Try diferent iocations for the chime closer to the button. Also, try to orient the chime at a different angle to increase the range. Range is most effective to the sides of the button.
LIMITED WARRANTY
The product you have purchased is guaranteed against defects in workmanship and materials for the period stated on the package. Waranties implied by law are subject to the same time period limitation. Some states do not allow limitations on how ong an implied warranty lasts, so this time limitation may not apply to you. If the product ails due to a manufacturing defect during normal use, return the product and dated sales eceipt to the store where purchased for replacement OR send the product and the dated sales receipt to:
Not Covered
Batteries, light bulbs, and other expendable items are not covered by this
warranty. Repair service, adjustment and calibration due to misuse, abuse or
negligence are not covered by this warranty. Unauthorized service or
modification of the product or of any furnished components will void this
warranty in its entirety. This warranty does not include reimbursement for
inconvenienoe, installation, setup time, loss of use, postage, unauthorized
service, or other products used in conjunction with, but are not supplied by,
1800doorbell.com All requests for replacement must include a dated sales
receipt (copies accepted) 800Doorbell.com and LHE, Inc. IS NOT LIABLE FOR LOST
PROFITS, INDIRECT, SPECIAL, EXEMPLARY, INCIDENTAL OR cONSEQUENTIAL DAMAGES
INCLUDING wITHOUT LIMITATION ANY sUCH DAMAGES DUE TO IMPROPER WIRING OR MISUSE
OF THE PRODUCT. As some states do not allow the exclusion or limitation of
ncidental or consequential damages, the above limitation and exclusion may not
apply to you
FCC
This device complies with Part 15 of the FCC Rudes Operation is subject to the
folowing wo conditions: (1) this device may not cause harmful interference,
and (2) this device must accopt any interference received, including
interference that may cause undesired operation
NOTE ThIS equipment has been tested and found to comply with the inris
for a Class B digital device, pursuant to Part 15 of the FOC Rudes. These its
are designed to provide reasonable protection against harmful interference in
a residential installation This oquijarment generates, uses and can radiate
radio frequency energy anad not installed and used in with the instructions,
may cause that interference to radio communications, However, thero is no
guarantee that interference will nat ocur in a particar installation this
equipment doos cause amphid interference to radio or televison reception,
which can bo determined by turning the equipment of and on the user is
encouraged to ty to corect the interference by one or mare d the folwing
measures:
- Reorient orralocato the receiving antenna
- Incresse the separation betvoen tho cqujprnent and rooeiver
- Connect the equipment into an outlet on a circuit different him that to which the receiver is connected
- Consult tho dealer or an experienced radkoTV technician for hoa
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>