WOLF E Series Microwave Oven Installation Guide

: June 9, 2024
: Wolf

Table of Contents

WOLF E Series Microwave Oven
E Series Oven
- Product Information
Safety Precautions
Specifications
- Installation Requirements
- Electrical Requirements
Installation
Electrical Connection
Troubleshooting
Efficiency Rating
Documents / Resources

WOLF E Series Microwave Oven

WOLF-E-Series-Microwave-Oven-product

E Series Oven

Features and speciﬁcations are subject to change at any time without notice.

Important Note

To ensure this product is installed and operated as safely and efficiently as possible, take note of the following types of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially important.
CAUTION indicates a situation where minor injury or prod-uct damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or death if precautions are not followed.
IMPORTANT NOTE: Save these instructions for the local electrical inspector.

Product Information

Important product information, including the model and serial number, are listed on the product rating plate. The rating plate is located near the bottom trim on the left.
The oven door must be open to view the rating plate. Refer to the illustration below.
If service is necessary, contact your authorized Wolf dealer.
Rating plate location

Safety Precautions

IMPORTANT INSTRUCTIONS

To avoid overheating, this appliance cannot be installed behind a decorative door.

Specifications

Installation Requirements

The E series oven can be installed in a standard or ﬂush inset application. If a cooktop is installed above an oven, a minimum of 6 mm is required between the units. The location of the electrical supply within the oven opening may require additional cabinet depth.
Finish the edges of the opening. They may be visible when the door is open.
For standard installations, the face trim overlaps stiles and rails. Refer to the chart below.
For ﬂush inset installations, a minimum 3 mm reveal is required on all sides. To ensure consistent reveals, each corner of the opening must be exactly 90°.

INSTALLATION REQUIREMENTS

Min Base Support 115 kg

TRIM OVERLAP

Top 25 mm
Bottom 0 mm
Sides 18 mm

Electrical Requirements

Installation must comply with all applicable electrical codes and be properly grounded (earthed).
Locate the electrical supply flush with the back wall and within the shaded area shown in the illustrations on the following pages. For ease of installation, the electrical supply for the oven can be placed in an adjacent cabinet within reach of the conduit.
Performance may be compromised if the electrical supply is less than 240 volts.
The oven is supplied with a single phase and 3-phase convertible power inlet box. The wiring diagram covering the control circuit is provided with the oven.

REQUIRED POWER SUPPLY

Single phase 220–240 V AC, 50/60 Hz
- 3-phase 380–415 V AC, 50 Hz
Maximum Connected Load 4.8 kW
Total Amps 20
Maximum Amps per Line 15
Rating plate location

IMPORTANT NOTE: Connection of this appliance should be through a fused connection unit or a suitable isolator, which complies with national and local safety regulations.

The on/off switch should be easily accessible after the appliance has been installed. If the switch is not accessible after installation (depending on the country) an additional means of disconnection must be provided for all poles of the power supply. When switched off there must be an all-pole contact gap of 3 mm in the isolator switch. This 3 mm contact disconnect gap must apply to any isolator switch, fuses, and/or relays according to EN60335.

CAUTION

The supply wiring must be protected to withstand temperatures up to 100°C.

30″ E Series Oven STANDARD INSTALLATION

NOTE: Location of electrical supply within opening may require additional cabinet depth.

30″ E Series Oven FLUSH INSET INSTALLATION

Shaded areas will be visible and should be finished to match cabinetry.
Dimension provides minimum reveals.
NOTE: Location of electrical supply within opening may require additional cabinet depth.

Installation

Preparation

Before moving the oven, protect any finished flooring and secure the oven door closed to prevent damage.
Use an appliance dolly to move the oven near the opening.
Place the appliance dolly on the side or back of the oven to prevent damage. Remove and recycle packing materials.
Do not lift or carry the oven by the door handle.

OVEN DOOR REMOVAL

To lighten the load, the oven door can be removed.
Remove only if necessary. Door removal should be done only by a certified installer or service technician. Do not lift or carry the oven door by the door handle.
To remove, open the door completely. Rotate both hinge locks back completely, remove the screw closest to the hinge on both sides of the door, and pull the door forward.
Refer to the illustration below.
To reinstall, slide the door onto the hinges. Rotate the hinge locks forward completely and install the screws.

Electrical Connection

WARNING

Verify power is disconnected from the electrical box before proceeding.
Open the terminal box to expose the screws with corresponding numbers. Run the cord through the strain relief hole and into the terminal box.
For a single phase installation (line, neutral, ground):
Loosen the 1, 5, and ground screws. Attach the line to position 1, the neutral wire to position 5, and attach the ground to the corresponding ground screw.
For 3-phase installation (L1, L2, L3, neutral, ground):
Loosen the 1, 2, and 3 screws and remove the copper bars.
Loosen the 5 and ground screws. Attach L1 to position 1,
L2 to position 2, L3 to position 3, the neutral wire to position 5, and attach the ground to the corresponding ground screw.
After tightening the screws, tighten down the cord strain relief and close the cover to the terminal box without pinching any of the wires.

WARNING

The copper bars must be removed from positions 1, 2, and 3 when connecting to 3-phase power.

Installation

Place the oven in the opening and slide into position. To ensure adequate depth for proper installation, the conduit must fit into the recessed area along the rear edge of the oven.
Locate the mounting hole in each side trim. Drill 1/16″ (2) pilot holes and install #6 x 3/4″ screws. Refer to the illustration below.
Remove and recycle packing materials including the white protective material behind each rack guide mounting location.

Door Alignment

To adjust the door, loosen the nuts on both sides of the door, manually adjust the door side to side, and tighten the nuts. Refer to the illustration below.

Troubleshooting

IMPORTANT NOTE: If the oven does not operate properly, follow these troubleshooting steps:
Verify electrical power is supplied to the oven.
Verify proper electrical connections.
If the oven does not operate properly, contact Wolf Factory Certified Service. Do not attempt to repair the oven. Wolf is not responsible for service required to correct a faulty installation.

Efficiency Rating

OVEN EFFICIENCY

Index 95
Class A
Energy (conventional ) 1.81 kWh
Energy (fan) 0.98 kWh
Elements 4
Capacity 115 L
NOTE: I n accordance with EU No. 65/2014 and 66/2014.
Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowflake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf,
Wolf & Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.
All other trademarks are property of their respective owners in the United States and other countries.
wolfappliance.com
WOLF APPLIANCE, INC. P.O. BOX 44848 MADISON, WI 53744 USA WOLFAPPLIANCE.COM 800.222.7820