IPRO S200 4G Smart Phone User Guide
- June 5, 2024
- IPRO
Table of Contents
IPRO S200 4G Smart Phone
Device location diagram
To turn on the device, press the switch button for 2-3 seconds.
Battery Charging
Batteries must be charged before they are first used. When charging, the charger should be close to the power socket and easy to unplug.
Insert card description
This device uses standard Nano-SlM and micro-SIM cards. If you need to replace
or purchase SIM cards please contact the network operator. Insert the needle
into the small hole on the SIM card
tray and pop up the card tray. Please insert the SIM card as shown in the
picture,
This will prevent the phone from being recognized or causing damage to the
card slot.
In case the phone cannot be recognized or the card slot is damaged
In order to avoid the cell phone can not identify or cause damage to the card
slot.
Dual Sim dual standby
According to your mood of dual sim dual standby management, work and life are
great. In the setting interface, click SIM card management,select 4G card slot
settings according to needs, and easily switch 4G networks
Dual card dual standby single channel instructions Your mobile phone adopts
the design of “dual sim dual standby” and the two cards inserted into the
phone can’t use voice services or data services at
the same time When one of the cards is on a call, the other card can’t answer
the phone. If someone just dials another card at the moment, you may hear
voice prompts such as’the number you dialed is not in service area’ The user
you dialed can’t be connected temporarily. please dial later” When one of the
cards is using data services, the data services of the other card can’t be
used. The above situation is a single channel feature of the moble phone,
which can significantly reduce power consumption, improve standby time, and
has nothing to do with the network status of operators.
security information
Before using the device, please read all safety information to ensure safe and correct use Use of an unapproved or incompatible power supply.charger or battery that may cause fire, explosion orother hazard. When charging the device, the power sockets should be installed near the device and easily accessible. When charging is complete or not, please disconnect the charger from the device and remove the chargingfrom the power socketIf the device is equipped with a non-removable internal battery, do not replace the battery by yourself to avoid damaging to battery or device, The battery can only be replaced by authorized service center. Please dispose the equipment, batteries and other accessories according to local regulations and do not treat them as domestic waste disposal. Batteries may explode if improperly disposed of. If other types of accessories are used, it may violate the warranty terms of the device and relevant provisions of the country where the device is located, and may lead to safety accidents.
For approved accessories, please contact the authorized service center.In
order to prevent possible hearing damage, do not use high volume for a long
time. Please use the device in the temperature range of 0 °C-35 °C, and store
the device and accessories in the temperature range of -20 °C-45 °C. When the
ambient temperature is too high or too low, it may cause device failure. Do
not expose the device and batteries to high temperature or heating device,
such as sunshine heater, microwave oven, oven or water heater. Overheating of
the battery may cause an explosion. Do not flashing by yourself f the user
adds the third-party ROMsystem or modifies the system files by cracking. the
system maybe unstable and may bring security risks and threats. IPRO will not
be responsible for these situations.
FCC Warning
Specific Absorption Rate (SAR) information SAR tests are conducted using
standard operating positions accepted by the FCC with the phone transmiting at
its highest certified power level in all tested frequency bands, although the
SAR is determined at the highest certified power level, the actual sARlevel of
the phone while operating can be well below the maximum value, in general, the
closer you are to a wireless base station antenna, the lower the power output.
Before a new model phone is a available for sale to the public, it must be
tested and certified to the FCC that it does not exceed the exposure limit
established by the FCC, Tests for each phone are performed in positions and
locations (e.g. at the ear and worn on the body)as required by the FCC. For
body worn operation, this mobile phone has been tested and meets the FCC RF
exposure guidelines when used with an accessory designated for this product or
when used with an accessory that contains no metal and that positions the
handset a minimum of 1.0cm from the body. This device complies with part 15 of
the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause
undesired operation.. Any Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equpment
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
OcCur in a particular installation. If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the equipment of and on, the user is
encouraged to try to corect the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV eshnisian for hel
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>