Tenda 4G07 LTE Router Installation Guide

Tenda 4G07 LTE Router

Package contents

• 4G LTE Router x 1
• Power adapter x 1
• Detachable antenna x 2
• Ethernet cable x 1
• Quick installation guide x 1

For product or function details, please go to www.tendacn.com to download the user guide.

Set up the router

1. Attach the antennas to the router.

2. Insert a SIM card into the slot on the bottom panel of the router.

3. Use the included power adapter to connect the PWR jack of the router to a power source.

4. Press the ON/OFF button down to turn on the router. The <!) LED indicator lights up. Wait a few seconds. The router is connected to the internet when the DI LED indicator lights up.

| Tips:
If the lJ LED indicator does not light up, refer to Q1 in FAQ.
---|---

Access the internet

• Connect your wired device, such as a computer, to the WAN/LAN or LAN port of the router using an Ethernet cable.
• Connect your wireless device, such as a smart phone, to the Wi-Fi network of the router using the WI-Fl Name and WI-Fl Key labeled on the bottom panel of the router.

To further configure the router, log in to the web UI of the router by visiting tendawifi.com on a connected device. You can also download the Tenda WiFi App on your smartphone to manage the router.

| Tips:
If you cannot log in to the web UI of the router, refer to Q3 in FAQ.
---|---

LED indicators

Wi-Fi LED indicator

| Solldon| The WI-Fi network is enabled.
Blinking| The router is ready for WPS negotiation.
Off| The Wi-Fi network is disabled.
|

LAN LED indicator

| Solid on| Pu least onedevice is connected to a LANport of the router.
Off| No device is connected to any LAN port of the router.
| Signal strength LED indicator| 3bars| Excellent signal.
2bars| Good signal.
1 bar Off| Fair signal.
No signal.

Ports & Buttons

Used to tum on or off the router.
PWR| Power jack.
Used to connect to a power source to supply power for the router.
RST/WPS| Used to reset the router, or start WPS negotiation of the router.

• Reset: Hold down the button for about Bseconds, and release it when all LED indicators light off and then light up.The router is reset.
• WPS: Through the WPS negotiation, youcan connect your wireless devices to the Wi-Fi network without entering the Wi-Fi password.
  Method: Press the button, and the Wi-Fi LED indicator blinks. Configure WPS- enabled wireless devices within 2 minutes to start WPS negotiation with the router.

WAN/LAN| It canserve as a WAN port or a LAN port.
By default,the router is under 3G/4G router mode and it serves as a LAN port. When the router is set to the wireless router mode, or the Failover function is enabled, it serves as a WAN port.
LAN| It canserve as a LAN port or an IPTV port.
When serving as a LAN port,it can be connected to a computer, switch or other LAN device.
When the IPTV function is enabled under the wireless router mode, it serves as the IPTV port to connect to the set top box.
Antenna socket| Used to connect to the included antennas to enhance the 3G/4G signal.

FAQ

Q1: The LED indicator does not light up. What should I do?
A1: Start a web browser, and access tendawifi.com:

• If you are required to enter a PIN code to unlock the SIM card, contact your ISP for the PIN code.
• If you are required to enter APN parameters manually, enterthese parameters provided by your ISP.
• If the ****LED indicator is still off after you finish the Quick Setup Wizard, your SIM card may run out of money. If the problem persists, contact your ISP for help.

Q2: I cannot access the internet after setting up the router. What should I do?
A2: Ensure that the ****LED indicator lights solid on. If not, refer to Q1.
If the problem persists, try the following methods:

• For wired devices, such as computers:
  – Ensure that your computer is connected to port WAN/LAN or LAN properly.
  – Ensure that your computer is set to obtain an IP address automatically and obtain DNS server address automatically.

• For wireless devices, such as smart phones:
  – Ensure that your wireless device connects to the Wi-Fi network of the router.
  – Log in to the web UI and change your Wi-Fi name and Wi-Fi password on Wi- Fi Settings > Wi-Fi Name & Password page. Connect to the Wi-Fi network you set and try again.

Q3: I cannot access the web UI of the router by visiting tendawifi.com. What should I do?
A3: Try the following solutions.
If you log In with a wireless device, such as a smartphone:

• Ensure that your wireless device is connected to the Wi-Fi network of the router.
• Disable the cellular network of your wireless device.
• Clear the cache of your web browser or change another web browser and try again.

If you log in with a wired device, such as a computer:

• Ensure that the computer has connected to the router properly.
• Ensure that the IP address of your computer is 192.168.0.X ()( ranges from 2 to 254). If not, unplug and replug one end of the Ethernet cable connecting the router and the computer, and try again.
• Clear the cache of your web browser or change another web browser and try again.

If the problem persists, reset the router (hold down the RST /WPS bun on for about 8 seconds) and configure it again.

Q4: Why cannot I find the Wi-Fi signal of the router?
A4: Connect your computer to port WAN/LAN or LAN of the router to log  n to the web
UI. Navigate to Wi-Fi Settings> Wi-Fi Name & Password and ensure that:

• Ensure that the Wi-R networks are enabled.
• Ensure that the Hide function is disabled.

Q5: How to change the Wi-Fi name and password?
AS: Try the following methods:
Method 1: Log in to the web UI of the router on a connected device, visit
tendawifi.com or 192.168.0.1 and navigate to Wi-Fi Settings> Wi-FI Name &
Password to change them.
Method 2: After you download the Tenda WiFi App and manage the router, run the App and find Toolbox > Wi-Fi Name & Password to change them.

Q6: Can I access the internet through both the SIM card and WAN port?
A6: When you insert a SIM card and connect the WAN/LAN port to the internet at the same time, you can configure the Fallover function on the Internet Settings page, so the router can provide internet access through another mode when the mode method fails.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
This equipment should be installed and operated with minimum distance 20cm between the device and your body.

Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operating frequency: 2412-2462MHz,5150-5250MHz,5725-5850MHz.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interlerence, it is recommended to use a shielded RJ45 cable.

CE MarkWaming

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
This equipment should be installed and operated with minimum distance 20cm between the device and your body.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.

Declaration of Conformity

Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment type 4G07 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: http://www.tendacn.com/en/service/download- cata-101.html

Operating Frequency:
2.4 GHz: EU/2400-2483.5MHz (CH1-CH13)
5 GHz: EU/5150-5250MHz (CH36-CH48)
EIRP Power (Max.):
2.4 GHz < 20dBm
5GHz< 23dBm
Software Version: V16.03.07.X

Caution:
Manufacturer: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD.
Adapter Model: BN073-A09009E, BN073-A09009B
Input: 100-240V AC 50/60Hz 0.4A
Output: 9V/1A
⎓: DC Voltage

Operating Environment

• Temperature: 0°C-40°C
• Humidity: (10 – 90) %RH, non-condensing

For EU/EFTA, this product can be used in the following countries:

Technical Support

Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, N0.1001, Zhongshanyuan Road, Nanshan District,
Shenzhen, China. 518052
USA hotline: 1-800-570-5892
Toll Free: 7 x 24 hours
Canada hotline: 1-888-998-8966
Toll Free: Mon – Fri 9 am – 6 pm PST
Hong Kong hotline: 00852-B1931998
Global hotline: +86 755-2765 7180 (China Time Zone)
Website: www.tendacn.com
E-mail: [email protected]

Copyright
© 2020 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda mndais a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd.
Other brand and product names mentioned herein are trademarks or registered trademarks of their respective holders. Specifications are subject to change without notice.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>