FOREST 520109X460 Diamond Sense Remote User Guide
- June 5, 2024
- FOREST
Table of Contents
FOREST 520109X460 Diamond Sense Remote
TECHNICAL SPECIFICATION
- 2x Alkaline battery type AAA, LR03
- battery life < 3 years
- frequency 433.92MHz
- transmit power max. 10mW
- transmit range indoor max. 30mtr
- working temperature -10°C – +50°C
- each channel can control up to 20 receivers
BATTERY EMPTY
After changing the battery, programmed receivers will stay in memory of
Diamond Sense remote. Please follow the local regulations for disposal of the
empty battery.
DISPLAY
UNLOCK THE MODE AND TIME BUTTONS Keep both buttons MODE and TIME pressed for about 4 seconds until the display shows ‘LOC’. Now you can set the mode and time.
MODE
- MAN Manual mode: automatic timer mode is off
- AUTO Auto mode: automatic timer mode is on
- AUTO Random mode: automatic timer mode is on, OPEN and CLOSE time will vary between + and – 15 minutes
To change the mode, keep ‘MODE’ pressed until the desired mode appears in the display:
SWITCHING BETWEEN 15 AND 2 CHANNELS
The default setting of the Diamond Sense is 15 channels. Channel 1 up to 15
can be used.
When desired, for example when you only have one or two motorized systems, you
can change the setting to 2 channels Keep both buttons, CH- and CH+ pressed
for about 8 sec until the display shows F-02. Now the Diamond Sense is a
2-channel remote control. To change back to a 15-channel remote control: Keep
both buttons, CH- and CH+ pressed for about 8 sec until the display shows
F-15. Now the Diamond Sense is a 15-channel remote control.
SET CURRENT TIME AND DAY (first unlock the buttons: press and hold MODE and TIME)
SET AUTOMATIC OPEN AND CLOSE TIME (first unlock the buttons: press and hold MODE and TIME)
In total up to 9 OPEN and 9 CLOSE timing positions can be set. For example use 4 points
- Position 1: Ma-Tu-We-Th-Fr 7:30 OPEN
- Position 2: Ma-Tu-We-Th-Fr 21:00 CLOSE
- Position 3: Sa-Su 7:00 OPEN
- Position 4: Sa-Su 20:00 CLOSE
SET TIMING POSITION 1 – OPEN
NEXT TIMING POINTS
can be set in the same way, press multiple times the MODE button until desired
timing position OPEN or CLOSE is reached. Maximum of 9 OPEN and 9 CLOSE
positions can be set.
You can recognize these Shuttle motors by the white antenna cable. To program a Diamond Sense to a Shuttle S / L / M Receiver, first select the desired channel and proceed
Same procedure, but press CLOSE instead of OPEN, will erase the programmed channel.
Do not mount the motor within 1 meter from other equipment and receivers. This will interfere with the receiver.
TECHNICAL SPECIFICATION
- powered by Shuttle M
- connect to port 1 of the Forest Shuttle M
- working temperature -10°C – +50°C
- controlled by Forest Multi Remote and Forest Multi-Wall Switch RF
Do not mount within 1 meter from other equipment and receivers. This will interfere with the receiver.
TECHNICAL SPECIFICATION FMS/BCS RECEIVER
- power: 100 – 240Vac 50/60Hz – 500Wmax.
- controls one tubular or FMS motor. When more motors → use group relay
- can also be used as wall switch
- terminal max. 2,5mm²
- working temperature -10°C – +50°C
Do not mount within 1 meter from other equipment and receivers. This will interfere with the receiver.
Please check the motor manual for setting the end limits
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Federal CommunicationsCommission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to tryto correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party
responsible for compliance could void the user’s authority to operate
theequipment.
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference,and
- this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this device.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>