HEB LIGHTING LN-75-12 Constant Voltage LED Driver Instruction Manual

HEB LIGHTING LN-75-12 Constant Voltage LED Driver

OVERVIEW

Features

• Dimming interface: 0-10V, 1-10V, 10V PWM, Resistor, AC Push-Dim
•  1 channel constant voltage output, Max. total output power 75W
• Synchronize on multiple LED drivers
• Over-heat / Over-load / Short circuit protection, recover automatically
• Full protective plastic case
• Suitable for indoor LED lighting application
• 5 Year, 50,000hr warranty

Mechanical Structures and Installations

Technical Parameters

Output

| Output Voltage| 12VDC| 24VDC
Output Current| Max. 6.25A| Max. 3.125A
Output Power| Max. 75W
Dimming Range| 0～100％
Ripple & Noise| <=200mV/230VAC
PWM Frequency| 2000Hz

Input

| Input Voltage Range| 200～240VAC
Frequency Range| 50/60Hz
Efficiency| 90％/230VAC
Alternating Current| 0.77A/230VAC| 0.75A/230VAC
Inrush Current| Cold start 27.5A at 230VAC
Leakage Current| ＜5mA
No Load Power| 1.5W/230VAC

Protection

| Over Load Power| Shut down the output when current load >= 120％～150％, auto recovers.
Short Circuit| Shut down automatically if short circuit occurs, auto recovers.
Over Temperature| Intelligently adjust or turn off the output current if the PCB temp > 100℃, auto recovers.

Environment

| Working Temperature| -30℃～50℃
T-case Max| 70℃
Working Humidity| 20％～90％RH, non-condensing
Storage Temperature/Humidity| -40℃～80℃, 10％～95％RH
Temperature Coefficient| ±0.03％/℃ (0-50％)
Vibration Resistance| 10-500Hz, 2G, 6min/cycle, X,Y,Z axes/2min
IP Rating| IP20

Safety&EMC

| Security Specifications| IEC/EN61347-1, IEC/EN61347-2-13
Withstand Voltage| I/P-O/P: 3750VAC
Insulation Resistance| I/P-O/P: 100MΩ/500VDC/25℃/70％RH
EMC Emission| EN55015, EN61000-3-2 Class C, IEC61000-3-3
EMC Immunity| EN61000-4-2.3.4.5.6.8.11, EN61547
Certifications| CE, EMC

Wiring Diagram

1. 0/1-10V Connection

• The 0/1-10V input is operable via commercially available simple rotary wall switches designed for 0/1-10V dimming equipment or from decicated system central dimming controllers.

• Compliant with 0-10V, 1-10V, 10V PWM, RX(4 in 1).

• We recommend the number of LED drivers connected to the 0/1-10V dimmer does not exceed 5 pieces,
  The maximum length of the wires from dimmer to the LED driver should be no more than 15 meters.

• If the LED driver is used with the RF remote or Push-Dim interface prior to using the 0/1-10V interface, the 0/1-10 V signal should change over 10% to return 0/1-10 V control.

AC Push-Dim connection

The provided AC Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switches.

Applications

• Suitable for LED-related fixture or appliances which use LED light bars and LED tape (like LED Decoration or Advertisement devices).

• Office / Commercial / Domestic Lighting, Hotels, Retail, and Display.

• Use for retrofit upgrades & new luminaire designs.

• Short press:
  Turn on or off the light.

• Long press (1-6s):
  Press and hold to step-less dimming,
  With every other long press, the light level goes in the opposite direction.

• Dimming memory:
  Light returns to the previous dimming level when switched off and on again, even at power failure.

• Synchronization:
  If more than one LED driver is connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to 100%.
  This means there is no need for any additional synchrony wire in larger installations.
  We recommend the number of LED drivers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to the LED driver should be no more than 20 meters.

Dimming Curve

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>