HEB LIGHTING PT-20A-2 Zigbee and RF Constant Current LED CCT Driver Instruction Manual

Zigbee & RF Constant Current LED CCT Driver
Model No.: PT-20A-2(WZ)

Features

• Dimming interface: RF Wireless, AC Push-Dim
• Tuya APP cloud control, support on/off, color temperature and brightness adjust, delay turn on/off light,timer run, scene edit and music play function
• Voice control, support amazon ECHO and Tall Genie smart speaker
• Match with RF 2.4G color temperature remote control, one RF LED driver accepts up to 10 remote controls
•  Universal AC input / Full range
• Flicker-free
• 2 channel constant current output, con
• Built-in active PFC function: 0.95 Typ
• Fade in and out effect selectable
• 3 levels color temperature (WW, NW and CW) selectable by continuous power off and on operation
• Over-heat / Over-load / Short circuit protection, recover automatically
• Full protective plastic case
• Suitable for indoor LED lighting application
• 5 Year, 50,000hr warranty

Mechanical Structures and Installations

Technical Parameters

declines, auto recovers when the load is reduced.
Short Circuit| Shut down automatically if short circuit occurs, auto recovers.
Over Temperature| Intelligently adjust or turn off the output current if the PCB temp > 100℃, auto recovers.
Environment| Waking Temperature| -30℃～50℃
T-case Max| 80℃
Working Humidity| 20％～90％RH, non-condensing
Storage Temp/Humidity| -40℃～80℃, 10％～95％RH
Temperature Coefficient| ±0.03％/℃ (0-50％)
Vibration Resistance| 10-500Hz, 2G, 6min/cycle, X,Y,Z axes/2min
IP Rating| IP20
Safety& EMC| Security Specifications| IEC/EN61347-1, IEC/EN61347-2-13
Withstand Voltage| I/P-O/P: 3750VAC
Insulation Resistance| I/P-O/P: 100MΩ/500VDC/25℃/70％RH
EMC Emission| EN55015, EN61000-3-2 Class C, IEC61000-3-3
EMC Immunity| EN61000-4-2.3.4.5.6.8.11, EN61547
Cortication’s| CE, EMC

LED Current Selection:

Applications

• Suitable for downlight, spotlight and decorative applications.
• Forehouse, Health care, Retail and Display.
• Use for retro

System wiring

1. ZigBee & RF Connection Note:
   

2.  The above distance is measured in spacious (no obstacle) environment, Please refer to the actual test distance before installation.

3. Please check if the WiFi router net in 2.4G band, the 5G band is not available, and do not hide your router network.

4. Please keep the distance between LED driver and router close, and check the WiFi signals.

5. Continuously switch off and on the power supply two times rapidly, It will change 3 levels color temperature (WW, NW and CW) in sequence.
   Tuya APP network connection
   Press and hold Match key for 5s, or push twice Match key fastly:
   Clear previous network connection, enter config mode, the LED indicator flash fastly, the output LED will flash 10 times.
   Repeat power on and off for 5 consecutive times, also clear previous network connection, enter Smart config mode, the output LED will flash 10 times.
   If Tuya APP network connection succeed, the LED indicator will stop flash, and in Tuya APP, you can find the ZB-CCT device.
   Match Remote Control (two match ways)
   End user can choose the suitable match/delete ways. Two options are offered for selection:
   Use Match key
   Match:
   Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) of the remote.
   Delete:
   Press and hold match key for 10s to delete all match, The light blinks 5 times means all matched remotes were deleted.
   Use Power Restart
   Match:
   Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful.
   Delete:
   Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted.

6. AC Push-Dim connection

The provided AC Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs.

• Short press:
  Turn on or off light.

• Long press (1-6s):
  Press and hold to step-less dimming, With every other long press, the light level goes to the opposite direction.

• Dimming memory:
  Light returns to the previous dimming level when switched off and on again, even at power failure.

• Synchronization:
  If more than one LED driver are connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to 100%.
  This means there is no need for any additional synchrony wire in larger installations.
  We recommend the number of LED drivers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to LED driver should be no more than 50 meters.

Fade in and Fade out Setting

Switch off the power, then switch on power, repeat again.
Immediately short press match key 3 times, the light on/off time will change between 3s and 0.5s.

Dimming Curve

PT-20A-2(WZ) Zigbee & RF Constant Current LED CCT Driver
User Manual Ver 1.0.0

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>