DOREL JUVENILE IH552TX Under Crib Smart Light User Guide

: June 5, 2024
: Dorel Juvenile

Table of Contents

In the Box
Features
Getting Started
Setup
Wi-Fi Connectivity
To Reset Device
Contact Us
Flat Surface Mounting
Removal
Disposal
IMPORTANT SAFETY INSTRUCTIONS
FCC/IC Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DOREL JUVENILE IH552TX Under Crib Smart Light User Guide

In the Box

Features

Wi-Fi Connectivity

Motion Detection

Adjustable LED Color & Brightness 1% – 100%

Auto dim after periods of inactivity

Simple to set up & install

Also use on toddler bed as a nightlight

Select a preset scene or create your own

Getting Started

Download Safety 1st App
Download the Safety 1st Connected app by searching for Safety 1st in the app store.

Setup

Before mounting, pair the device and test its functionality.
Insert the USB cable into the adapter and plug the adapter into the wall outlet.
The crib light will glow red, indicating it is ready for pairing.
On your mobile device, follow the step by step instructions in the Safety 1st Connected app for setup.
Once paired, the crib light will glow white.
Explore the features and functionality within the Safety 1st Connected app.

Wi-Fi Connectivity

A 2.4GHz Wi-Fi internet connection is required.

Check the Wi-Fi signal strength from your router.

To reduce signal interference or echoes , avoid placing the crib light near major electrical appliances, large metal or concrete surfaces.

To Reset Device

The device must be plugged in to the power source in order to reset. Press and hold power button for 6 seconds to reset the device. The crib light will glow red when the device is reset and ready to be paired in the app.

SCAN HERE For support

Contact Us

You can also:

Send Us a Text: 1-812-203-4747
(US and Canada Only
Carrier Fees May Apply)

Find Us Online: www.safety1st.com
Email Us: support@djgusa.com

Give Us a Call: 1-800-544-1108
(Toll Free, US and Canada Only)

Flat Surface Mounting

Clean the desired mounting surface using a damp cloth, then dry, ensuring there is no dust or other residue.
Determine the center of the crib and lay out the crib light, cables, and cable management clips. Make sure there will be enough cable to reach your nearest electrical outlet once the crib light is installed.
Apply 2 pieces of doublesided mounting tape to the the back of the crib light and 2 pieces to the back of the control unit.
Adhere the crib light to the underside of the crib.
Apply fi rm pressure against the crib light and mounting surface for 10 seconds to ensure proper adhesion. Adhere the control unit to the side of the crib frame, nearest to the doorway so the motion sensor can be promptly activated.
Apply fi rm pressure against the control unit and mounting surface for 10 seconds to ensure proper adhesion.
Use the included (6) cable management clips to keep cable off of the ground. Keep clips off of the ground and out of reach of children.

Removal

To remove the crib light and control unit, carefully slide a piece of fi shing line or dental floss between the crib, crib light, and control unit.

Then in a sawing motion, cut the adhesive away from the crib. Rub and roll the remaining adhesive off of the crib, crib light, and control unit.

Note: You may also use the heat from a hair dryer on the lowest setting to help
soften the adhesive to aid in its removal from the crib. Before doing so, remove all bedding and the mattress from the crib.

Disposal

Keep product away from hot, humid areas or strong sunlight, and do not let it get wet.

Every effort has been made to ensure high standards of reliability of your product.

However, if something does go wrong, please do not try to repair it yourself – contact Consumer Care for assistance.

At the end of the product life cycle, you should not dispose of this product with normal household waste. Take this product to a collection point for the recycling of electrical and electronic equipment.

Some of the product materials can be reused if you take them to a recycling point.

By reusing some parts or raw materials from used products you make an
important contribution to the protection of the environment. Please contact yourrecycling center in case you need more information on the collection points in your area.

WARNING:

Adult installation is required. Keep small parts away from children when installing. Exercise care when unpacking the product.
This product is intended to be attached UNDER the crib, where it is least likely to be accessed by the child when placed inside the crib.
To prevent possible injury by entanglement, KEEP OTHER CHILDREN away from cords.

CAUTION:

These products are not toys. DO NOT allow children to play with them. DO NOT use product if damaged or broken.

THE USER SHOULD NOT ATTEMPT TO SERVICE OR REPAIR THE CRIB LIGHT. ALL SERVICING SHOULD BE REFERRED TO CONSUMER CARE.

It is essential to check reception regularly. Crib light uses encrypted transmission over FCC managed frequencies. Always remember to password protect your Wi-Fi router.

IMPORTANT SAFETY INSTRUCTIONS

HEAT: The crib light should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances that produce heat. Also keep these components out of direct sunlight.
POWER CORD PROTECTION: The power supply cord should be routed so that it is not likely to be walked on or pinched by items placed upon or against it. Pay particular attention to the cord at the plug, convenience receptacle, and at the point it exits from the crib light.

FCC/IC Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will notoccur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning this equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifi cations not expressively approved by Dorel Juvenile Group can void your authority to operate this equipment under Federal Communications Commission’s rules.
Use of other accessories may not ensure compliance with the FCC exposure guidelines.
CAUTION : This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 8 in. (20 cm) between the radiator and your body.

IC Information

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication. This Class B digital apparatus complies with Canadian ICES-005.

Warranty

Dorel Juvenile Group warrants this product against defective materials
or workmanship. For more information or to make a claim, visit www.safety1st.com/warranty.

Apple, the Apple logo, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.

Android is a trademark of Google Inc. Google Play is a trademark of Google Inc. All other trademarks are the property of their respective owners.

©2021 Dorel Juvenile Group, Inc. Safety 1st™ and the Safety 1st logo and design are trademarks of Dorel Juvenile Group, Inc. 800-544-1108 www. safety1st.com. Styles and colors may vary. Made in CHINA.Distributed by
Dorel Juvenile Group, Inc., 2525 State St., Columbus, IN 47201-7494. Dorel Juvenile Canada, 2233 Argentia Road, Suite 110, Mississauga, ON L5N 2X7. Fono (562) 2339 9000.
Tel. (55) 67199202 08/21 4358-8170

``