better bathrooms BeBa_25341 Mojave Horizontal Radiator User Manual
- June 5, 2024
- Better Bathrooms
Table of Contents
better bathrooms BeBa_25341 Mojave Horizontal Radiator
Important information
- Please read these instructions thoroughly and retain for future reference
- Manufactured to BS EN 442-1 Radiators and convectors
- Please ensure that the product is checked for damage prior to installation, any damage reported after installation will not be covered.
- The pipework must be flushed out to remove any debris which can affect the function of this product.
- A corrosion inhibitor should be used in your installation.
BTU & Wattage info-
Product Code| BTU| Wattage| Product Code| BTU|
Wattage
---|---|---|---|---|---
BeBa_25341| 1198| 351| BeBa_27940| 1809| 530
BeBa_25342| 1429| 444| BeBa_27941| 5242| 1536
BeBa_25343| 2145| 628| BeBa_27942| 5874| 1721
BeBa_25344| 2394| 702| BeBa_27943| 5874| 1721
BeBa_25345| 1516| 444| BeBa_27944| 6852| 2008
BeBa_25346| 1809| 530| BeBa_27945| 7831| 2295
BeBa_25347| 1682| 493| BeBa_27946| 2781| 815
BeBa_25348| 1890| 554| BeBa_27947| 3823| 1121
| | | BeBa_27948| 5561| 1630
Parts
- 1 x Radiator
- 1 x Air Vent (Bleed Valve)
- 1 x Blanking Cap
- 8 x Wall Plug
- 4 x Wall Bracket
- 8 x Washer
- 8 x Wall screw
- 4 x Wall Bracket Cover
Please note that Parts are for illustrative purposes only and may differ
slightly to the actual product
Tools required
- Spanner
- Flathead screwdriver
- Philips screwdriver
- Tape measure
- Drill and 8mm drill bit
- Spirit Level
- Pencil
- Sealing tape
Installation
Please note: Before starting any installation, turn off the water supply.
Please note: Before commencing any installation, the desired location
should be checked before drilling, that no pipes or wires can be damaged.
First, prepare the water supply pipes to match up with the towel radiator and
valve dimensions being used. Fit the radiator valve tail and nut into the
radiator (at both sides) and using sealing tape, tighten into position, then
follow the installation below.
- Insert the blanking cap and air vent in the top of the radiator at either side, (add alittle sealer tape to secure) and tighten using the spanner, be sure not to overtighten.
- Set the position of the wall hanging brackets (on the wall) in relation to the size of your radiator, the brackets should be located between the last bar and the second bar in, as shown. Mark these positions on the wall in the required location and use a spirit level to ensure that these are horizontally and vertically aligned.
- Using the drill and 8mm drill bit, drill into the marked positions then insert the wall plugs and tap flush to the finished wall surface. Please note: If drilling into tile, it is recommended to tape the wall to prevent the drill from slipping.
- Next, position the wall brackets and screw into place using the screws provided (securing each with a washer) with the Philips screwdriver. Then place the bracket covers over the curved section of the bracket which sits between the radiator and the bracket.
- Once all brackets are secure, hang the radiator until fixed firmly into place and adjust so that the radiator aligns with the pipework. Please note: You may need two people to hang the radiator, depending on the model purchased.
- Finally, fit the radiator valves to the pipework and connect to the radiator valve tails and tighten all connections.
IMPORTANT! The product is supplied un-filled. The radiator should be filled with a water (80%) and glycol (20%) mixture if NOT being connected to the central heating system, also allow 5% air gap.
After installation
- After the above installation, turn on the water supply and using the flathead screwdriver, open the air vent via the central screw, open the inlet valve and let the water rush into the radiator. Check all connections for leaks.
- Once water overflows from the air vent, this means that there will be no air bubbles present.
- Use a screwdriver to close the air vent and then the radiator is ready to use.
Cleaning
This radiator is made from steel with a painted finish. To maintain the surface of your product, wipe with a clean damp cloth and wipe dry. Do not use abrasive cleaning agents or materials which can strip and scratch the surface; the use of these agents or materials can invalidate your guarantee. It is recommended to wipe and dry on a regular basis.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>