greenworks SSF405 40V 12 Inch Snow Shovel User Manual

greenworks SSF405 40V 12 Inch Snow Shovel

DESCRIPTION

PURPOSE
This machine is used to remove and clear away snow from pavements, gardens, driveways and other ground-level surfaces.

OVERVIEW

1. Battery compartment
2. Lock-out button
3. Trigger
4. Impeller
5. Scraper
6. Lower shaft
7. Auxiliary handle
8. Upper shaft

GENERAL POWER TOOL SAFETY WARNINGS

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your battery­operated (cordless) power tool.

TRAINING

• Do not allow children under the age of 14 to operate this tool. Children who are 14 years of age or older must read and understand the operating instructions and safety rules in this manual and must be trained and supervised by a parent.
• Read the operating and service instruction manual carefully. Be thoroughly familiar with the controls and the proper use of the power tool. Know how to stop the unit and disengage the controls quickly.
• Never allow children to operate the power tool. Never allow adults to operate the power tool without proper instruction.
• Keep the area of operation clear of all persons, particularly small children, and pets.
• Exercise caution to avoid slipping or falling, especially when operating in reverse.
• Do not use on graveled surfaces.
• Dress Properly – Do not wear loose clothing or jewelry. They can be caught in moving parts.
• Wear appropriate boots when operating the snow thrower. Operation of the snow thrower in the hand-held position is unsafe, except in accordance with the special instructions for such use provided in the operator’s manual.

PREPARATION

• Thoroughly inspect the area where the power tool is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.
• Do not operate the power tool without wearing adequate winter garments. Wear footwear, which will improve footing on slippery surfaces.
• Adjust the housing height to clear gravel or crushed rock surface.
• Never attempt to make any adjustments while the machine is running ( except where specifically recommended by the manufacturer).
• Always wear safety glasses or eye shields during operation or while performing an adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery pack, picking up or carrying the appliance. Carrying the appliance with your finger on the switch or energizing appliance that
• have the switch on invites accidents.
• Disconnect the battery pack from the appliance before making any adjustments, changing accessories, or storing the appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.
• When battery pack is not in use, keep it away from other metal objects,like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

OPERATION

• Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.
• Exercise extreme caution when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.
• After striking a foreign object, turn the machine off and remove the battery pack, and then inspect it for damage. Repair any damage before restarting and using the machine.
• If the power tool should start to vibrate abnormally, stop the machine and check immediately for the cause. Vibration is generally a warning of trouble.
• Stop the machine whenever you leave the operating position, before unclogging the collector/impeller housing or discharge guide, and when making any repairs, adjustments, or inspections.
• When cleaning, repairing, or inspecting, make certain the collector/impeller and all moving parts have stopped.
• Exercise extreme caution when operating on slopes.
• Never operate the snow thrower without proper guards, keep other safety protective devices in place and working.
• Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.
• Don’t Overreach- Keep proper footing and balance at all times.
• Do not overload the machine capacity by attempting to clear snow at too fast a rate.
• Don’t Force Snow Thrower – It will perform better and safer at the rate for which it was designed.
• Never operate the power tool at high transport speeds on slippery surfaces. Use care when reversing.
• Never direct discharge at bystanders or allow anyone in front of the power tool.
• Disengage power to the collector/impeller when the power tool is transported or not in use.
• Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).
• Never operate the power tool without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles.
• Walk, never run.
• Clearing a Clogged Discharge Chute.
• Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the discharge chute. To clear the chute:
  1. SHUT THE ENGINE (Motor) OFF!
  2. Wait 10 seconds to be sure the impeller blades have stopped rotating.
  3. Always use a clean-out tool, not your hands.

If the snow thrower strikes a foreign object follow these steps:

1. Stop snow thrower. Release the switch.
2. Remove the battery pack.
3. Inspect for damage.
4. Repair any damage before restarting and operating the snow thrower.

MAINTENANCE

• Check shear bolts; engine-mounted bolt, etc., at frequent intervals for proper tightness to be sure the power tool is in safe working condition.

• Always refer to owner’s guide instructions for important details if the power tool is to be stored for an extended period.

• Store Idle Snow throwers Indoors – When not in use, snow throwers should be stored indoors in a dry, locked­up place – out of reach of children.
  Run the power tool a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

• Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.

• Do not expose a battery pack or appliance to fire or excessive temperature space. Exposure to fire or temperature above 265°F (130°C) may cause an explosion.

• Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.

• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.

• Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated in the instructions for use and care.

• Maintain Snow Thrower with care – follow instructions for changing accessories.

SYMBOLS ON THE PRODUCT

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.

RISK LEVELS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

ENVIRONMENTALLY SAFE BATTERY DISPOSAL

The toxic and corrosive materials below are in the batteries used in this machine: Lithium-Ion, a toxic material.

WARNING

• Discard all toxic materials in a specified manner to prevent contamination of the environment. Before discarding a damaged or worn-out Li-ion batteries, contact your local waste disposal agency, or the local Environmental Protection Agency for information and specific instructions. Take the batteries to a local recycling and/or disposal center, certified for lithium-ion disposal.
• If the battery pack cracks or breaks, with or without leaks, do not recharge it and do not use. Discard it and replace with a new battery pack. DO NOT TRY TO REPAIR IT! To prevent injury and risk of fire, explosion, or electric shock, and to avoid damage to the environment:
  • Cover the terminals of the battery with heavy-duty adhesive tape.
  • DO NOT try to remove or destroy any of the battery pack components.
  • DO NOT try to open the battery pack.
  • If a leak develops, the released electrolytes are corrosive and toxic. DO NOT get the solution in the eyes or on skin, and do not swallow it.
  • DO NOT put these batteries in your regular household trash.
  • DO NOT incinerate.
  • DO NOT put them where they will become part of any waste landfill or municipal solid waste stream.
  • Take them to a certified recycling or disposal center.

PROPOSITION 65

WARNING
This product contains a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints;
• Crystalline silica from bricks and cement and other masonry products;
• Arsenic and chromium from chemically treated lumber.

Your risk of exposure to these chemicals varies depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well- ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

INSTALLATION

WARNING

• Do not install the battery pack until you assemble all the parts.
• Make sure that you correctly assemble the machine before
• If the parts are damaged, do not use the machine.
• If you do not have all the parts, do not operate the machine.
• If the parts are damaged or missing, speak to the service center.

1. Open the package.
2. Read the documentation in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and package in compliance with local regulations.

ATTACH THE SHAFT

NOTE
If the button does not release fully in the location hole, the shafts are not locked into position. Tum from side to side until the button is locked into position.

1. Loosen the lock knob (12) on the coupler (11).
2. Align the release button (9) with the location hole (10) and move the two shafts together.
3. Turn the upper shaft (8) until the release button (9) locks into the location hole (10).
4. Tighten the lock knob (12).

ATTACH THE AUXILIARY HANDLE

1. Push the auxiliary handle (7) onto the upper shaft (8).
2. Move the auxiliary handle (7) above the metal ring (13) and make sure that the metal ring (13) fits between the slot on the auxiliary handle (7).
3. Align the holes on the auxiliary handle (7) and the metal ring (13).
4. Put the handle knob (14) through the holes and tighten it.

INSTALL THE BATTERY PACK

WARNING

• If the battery pack or charger is damaged, replace the battery pack or the charger.
• Stop the machine and wait until the engine stops before you install or remove the battery pack.
• Read, know, and do the instructions in the battery and charger manual.

1. Align the lift ribs on the battery pack ( 16) with the grooves in the battery compartment (1).
2. Push the battery pack ( 16) into the battery compartment (1) until the battery pack locks into place.
3. When you hear a click, the battery pack is installed.

REMOVE THE BATTERY PACK

1. Push and hold the battery release button.
2. Remove the battery pack (16) from the machine.

OPERATION

START THE MACHINE

1. Push and hold the lock-out button (2).
2. Pull the trigger (3) to start the machine.
3. Release the lock-out button (2).
   WARNING
   Examine the work area. Remove all stones, sticks, wire, bones, and other debris that can ricochet because of the rotating impeller.

STOP THE MACHINE

1. Release the trigger (3) to stop the machine.

OPERATE THE MACHINE

1. Start the machine.
2. Push the machine forward until it rides on the scraper (14).
   NOTE The forward speed is dependent on the depth and weight of the snow.

MAINTENANCE

CAUTION

• Do not let brake fluids, gasoline, or petroleum-based materials touch the plastic parts. Chemicals can cause damage to the plastic, and make the plastic unserviceable.
• Do not use strong solvents or detergents on the plastic housing or components.

GENERAL MAINTENANCE

• Before each use, examine the machine for damaged, missing, or loose parts such as screws, nuts, bolts and caps.
• Tighten correctly all the fasteners and caps.
• Clean the remaining snow on the machine with a brush.

REPLACE THE SCRAPER

1. Put the machine on a flat, level surface.
2. Face up the impeller (4).
3. Remove the 4 screws below the impeller (4) that attach the scraper ( 5) to the machine.
4. Remove the worn scraper (5).
5. Install the new scraper (5).
6. Install and tighten the screws (15) that you removed.

REPLACE THE IMPELLER

1. Remove 6 screws on the right side cover.
2. Pull the belt tensioner away from the engine pulley. Make sure that the washer, spring and screw are not missing.
3. Remove the belt.
4. Remove the 4 screws.
5. Remove the 6 screws on the left side cover.
6. Remove the nut on the left side plate.
7. Remove the impeller shaft with pulley assembly attached.
8. Remove the damaged impeller (13). Make sure that the shaft sleeve on the left side of the shaft is not missing.
9. Install the impeller shaft with pulley assembly attached in the new impeller. Make sure that you replace the retained shaft sleeve on the left side of the shaft.
10. Replace and tighten the retaining nut on the left side plate assembly, screws on the left side cover and screws on the pulley assembly.
11. Put the belt and the belt tensioner into position.
12. Replace and tighten the remaining screws on the right side cover.

TRANSPORTATION AND STORAGE

• Clean the machine before storage.
• Make sure the engine is not hot when you stow the machine.
• Make sure that the machine does not have loose or damaged parts. If it is necessary, do these steps/ instructions:
  • Replace the damaged parts.
  • Tighten the bolts.
  • Speak to a person of an approved service center.
• tow the machine in a locked, dry area.
• Make sure that children cannot come near the machine.
• When you move the machine, hold it by the top handle and auxiliary handle.

TROUBLESHOOTING

the height of the handle and make sure that the knobs and bolts are aligned cor- rectly.
The machine does| The battery is not| Charge the battery
not start.| charged.| by following the
 |  | procedures in the
 |  | battery and charg-
 |  | er manual.
 | The switch is de-| Have the switch
 | fective.| replaced by an au-
 |  | thorized service
 |  | center.
 | Battery is too cold.| Remove battery
 |  | from snow throw­
 |  | er. Place battery on
 |  | charger and allow
 |  | to charge for 10
 |  | minutes or until
 |  | the changing light
 |  | turns green. Re­
 |  | move from charger
 |  | and install in snow
 |  | thrower for use.
 | Battery may re-| Call toll free help-
 | quire service or re-| line , at or replace
 | placement.| battery.
The engine is on, but the impeller does not turn.| The belt is dam­ aged.| Replace the belt.
A thin layer of snow stays behind.| The scraper is damaged.| Replace the scra­ per.

If you cannot find the solution to these problems, call .

TECHNICAL DATA

The recommended ambient temperature range:

°C)

Snow   shovel operation  tern-    1.4 °F (-17 °C) – 104 °F (40 perature  range °C)
Battery charging temperature 39 °F (4 °C) – 104 °F (40 °C) range
Charger  operation   tempera-      39°F (4 °C) – 104 °F (40 °C) ture range
Battery discharging tempera- 6.8°F(- l 4 ° C) – 113 °F (45 ture range °C)
Battery storage temperature range| I year: 32°F (0°C) – 73°F (23°C)
3 month: 32°F (0°C) – 113°F (45°C)
1 month: 32°F (0°C) – 140°F (60°C)

LIMITED WARRANTY

hereby warranties this product, to the original purchaser with proof of purchase, for a period of three (3) years against defects in materials, parts or workmanship. , at its own discretion will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer. This warranty is valid only for units which have been used for personal use that have not been hired or rented for industrial/ commercial use, and that have been maintained in accordance with the instructions in the owners’ manual supplied with the product from new.

ITEMS NOT COVERED BY WARRANTY:

1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner’s manual; or
3. Normal wear, except as noted below;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.

HELPLINE:
Warranty service is available by calling our toll-free helpline, at .

TRANSPORTATION CHARGES:
Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by .

USA address:

• Greenworks Tools
• P.O. Box 1238
• Mooresville, NC 28115

Canadian address:

• Greenworks Tools
• Canada Inc. 1110 Stellar
• Drive Unit 102
• Newmarket, ON, L3Y 7B7

EXPLODED VIEW

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>