BECEN BC-M200 200W LED Beam Move Head Light User Manual

: June 5, 2024
: BECEN

Table of Contents

BECEN BC-M200- 200W LED -Beam- Move -Head -Light
Installation and attention
Product Instruction
Panel operation
Operation
Total: Cumulative hours of operation
Channel description
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BECEN BC-M200- 200W LED -Beam- Move -Head -Light

Installation and attention

Maintenance

To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
Intermittently using will extend this item’s service life.
Please clear the fan ,fan net , and optical lens in order to keep good work state.
Do not use the alcohol or any other organic solvent to wipe the shell.

Statement
The product has perfect performance and integrity packing. All users should be strictly complying with the warning and operating instructions as stated. Or we aren’t in charge of any result by misusing. Any damage resulting by misuse is not within the Company’s warranty. Any fault or problem caused by neglecting the manual is also not in the charge of dealers.

Safety Precaution

In order to guarantee the product’s life, please don’t put it in the damp places or even the environment over 60degress.
Always mount this unit in safe and stable matter.
Install or dismantle should operate by professional engineer.
Using lamp，the change rate of power voltage should be within±10%，If the voltage is too high，it will shorten the light’s life; If it’s not enough, will influence the effect.
Please restart it 20 minutes later after turning off light , until full-cooling. Frequent switching will reduce the life span of lamps and bulbs; intermittent using will improve the life of bulbs and lamps.
In order to make sure the product is used well, please read the Manual carefully.

Product Instruction

lamp: Philips MSD Platinum 5R or YODN 5R (life:2200 hours Color temperature: 8000K)
Channel mode:20 DMX512 Channel
Pan scan：540°(16bit) Electric correction
ilt scan：270° (16bit) Electric correction
Over heat protection
Power Input: 100-240V，50/60Hz
Power ：290W
IP level :IP20
Net weight：13.5KG

Cable connection（DMX）
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors. BECEN BC-M200- 200W LED -Beam-
Move -Head -Light -fig 1

Figure 1 DMX Cable connection
Rigging (Optional)
This equipment can be positioned and fixed by clamp in every direction of the stage. Locking system makes it easy to fasten to the bracket.
Attention! Two clamps is needed to fix the equipment. Every clamp is locked by fastener of 1/4 kind. Fastener can only be locked clockwise.
Attention! Fasten a safety string to the additional hole of side aluminum piece. The secondary accessory can not hang on the delivery handle. Nip the equipment on bracket.

Check if rigging clamp (not including the one inside) damaged or not? If stand ten times weight as the equipment. Make sure the architecture can stand ten times weight as all the equipments, clamps, wirings and other additional fixtures.
Screws for clamping must be fixed firmly. Take one M12 screw (Grade 8.8 or higher) to clamp bracket, and then screw the nuts.
Level the two hanging points at the bottom of clamp. Insert fastener to the bottom, lock the two levers by 1/4 rotating clockwise; then install another clamp.
Install on safety string which stands at least ten times weight as equipment. Terminal of the accessory is designed for clamps.
Make sure pan/tilt lock unlocked or not. Keep the distance more than 1M from equipment to flammable material or lighting source.

Panel operation

Brief
The light panel diagram show as Figure 2, Left area is TFT Displayer, support touch, and right area is KEY, both of touch and KEY can operate light and setting. Display & operation just like ‘Android operation system’, touch the item will set or modify setting.
Note : Prevent damage the touch or TFT displayer, Can not use sharp objects chick displayer.

Operation

Operate light with touch or KEY

The left area is TFT Displayer and touch, chick item or value with finger will to complete operation of set light setting(parameters) or view light state.
The area on the right hand side is 4 KEY, As auxiliary input interface, if disable touch function,, the KEYr can been choose to set the parameter.
Parameter value setting

When the selected item is value need to been modified, the dialog shown in Figure 3 will popup. BECEN BC-M200- 200W LED -Beam- Move -Head -Light -fig
3

Modify value： Can quickly modify value via pull the slider to the desired position, or click the button of ‘up’ or ‘down’ whit finger on the right side to set the exact desired value, another way is roll encoder on the right hand side of panel.
Apply value ：When Value had been modified, Then press the bottom of ‘apply’ in the left corner to apply to the light, but hav’t saved；
Save Value ：Any time, click on the lower right corner of the “OK” button, the setting will been saved into internal memory.
Boolean parameter setting
when the selected parameters is a Boolean value (such as ON or OFF), can directly modify setting by chick corresponding item, the setting will been saved right now.
When the parameter is a key item, chick corresponding item, a dialog shown in Figure 4 will been popup ask for the confirm. Chick ‘sure’ to confirm.

Figure 4 Dialog of confirm
Sub Menu（Parameter）
Chick item of main menu, enter corresponding sub menu, shown in Figure 5, total 6 sub menu, includes class of parameter and status:

ADDRESS：Set light DMX address.
WORKMOD：Set light work mode, master or slave mode when in auto run mode.
DISPLAY： Set display parameter, eg. select language.
TEST：Used for test light, modify DMX channel data to test function， the corresponding function of reference channel function table.
ADVANCE：Set light running parameter.
STATUS：view light current status.

Operation and parameter instruction

Via following operation, enter sub menu(parameter menu) shown in Figure 5

In main menu, chick 1/6 function button into corresponding parameter menu.
In sub menu(page), chick main item on the left side of displayer, can shift to corresponding sub menu(page) quickly.

ADDR– > Address: Set DMX Address

Click and select the “ADDR”, can enter the page of DMX address setting, range from 1 to 512, the address code shouldn’t is not greater than (512- channels quantity), otherwise the light will not been controlled. Following is the operation: Enter the page of DMX address, as shown in Figure 6, click the blank area in right side of display will pop-up diglog as in Fig. 4, modify value, then click ‘ENTER’ to confirm and save DMX address code.

MODE– > WorkMode: Set Light work mode
Enter the page of ‘WorkMode’ as shown in Figure 7 and modify setting. Can set light work mode, control lamp and DMX channel mode.

DMX Ctrl: Choose to set DMX Mode,
Auto Run: Choose to set Auto Mode,
Sound Ctrl Choose to set Sound Mode,
M/S Choose vailable just in ‘AUTO RUN’ or ‘SOUND Ctrl’ mode.

ON–> Master. (Data will be send to another slave lamp immediately.) OFF–> Slaver.(NOT send data to other lamp via DMX Cable).(Default)

Light Switch: ON–> Turn on the light, OFF–> Turn off the light.
Channel Qty: Light support 2 DMX Channel mode: sample or extend。 Simple –> 16CH.(Default) Expand–> 20CH(or null).

DISP– >DISPLAY: Set display
Light support 2 language, rotation display，Enter page as shown in Figure8 to set parameter following:

Language: English
Screen Saver : when panel is idle(these is no operation in 10 second), displayer will enter saver status.
OFF–> No screen saver.
Mode1–> Power-saving mode, turn off the display.
Mode2–> Displays the current address.
Mode3–> Displays the icon and the current working mode.(Default)
Screen Rotion: To turning display. ON–> Normal display.(Default) OFF–> 180° turning display.
Touch enable ：Disable or enable touch function,. ON–> Enable touch function.(Default) OFF–> Dosable touch function.
Touch adjust： Adjust touch function. Normally, not enter this item.

TEST– > TestMode
Enter the page as shown in Figure 9, Light will into test mode, in this mode, the light does not receive the data for DMX controller.:

PAN: range for 0 to 255;
TILT: range for 0 to 255;
FOCUS: range for 0 to 255;
COLOR: range for 0 to 255;
GOBO: range for 0 to 255;
PRISM: range for 0 to 255;
FROST: range for 0 to 255;
STROBE range for 0 to 255;

ADVA– >Advanced: Set light run parameter

Enter the page as shown in Figure 9, set the parameter of light:

Pan Invert: Reverse PAN move OFF–> Pan Normal move.(Default) ON–> Reverse PAN move.
Tilt Invert: Reverse TILT move OFF–> Tilt Normal move.(Default) ON–> Reverse Tilt move.
P/T Rectify: Disable or enable position rectify function. OFF–> Disable P/T rectify ON–> Enable P/T rectify-(Default)
Pan Offset: Set PAN original position. Default: 10
Tilt Offset: Set TILT original position. Default: 10
Lamp when: PowerON–> Turn on the lamp when power on.(Default) RstDone–> Turn on the lamp after reset. Manual–> Manually turn on the lamp.
Data hold: OFF–> When no DMX signal,return to middle position.(Default) ON–> When no DMX signal,stop in the final position.
Factory Setting: Restore all parameter to factory setting.

STAT– >Status: View status Enter the page as shown in Figure 11:

Work Mode : Show the current working mode.
Address: Show the current address.
Version: Show the version of the lamp.
Elapse: Working hours after turn on

Total: Cumulative hours of operation

Channel description

Channel table

CH1	PAN	0-255	0-540°
CH2	TILT	0-255	0-270°
CH3	PAN 16bit	0-255	Pan fine
CH4	TILT 16bit	0-255	Tilt fine
CH5	XY Speed	0-255	Fast to slow

CH6

|

Strobe

CH8

|

Color

CH9

|

Gobo

| 0-9| White
10-19| GOBO1
20-29| GOBO2
30-39| GOBO3
40-49| GOBO4
CH1| PAN| 0-255| 0-540°
---|---|---|---
CH2| TILT| 0-255| 0-270°
CH3| PAN 16bit| 0-255| Pan fine
CH4| TILT 16bit| 0-255| Tilt fine
CH5| XY Speed| 0-255| Fast to slow