BECEN BC-RGB10W 10w Laser Show System User Guide

BECEN BC-RGB10W 10w Laser Show System

Like above picture，
MODE： Press one time change one mode
UP、DOWN： when in PRG and IL mode short press to change the working file, long press to change the whole folder, when in sound mode, it’ll change the acoustic sensitivity.

matters needing attention

1. The optimum temperature range of laser lamp is 20 ~ 35 ℃.
2. Do not direct the laser at human eyes to avoid injury.
3. Please do not use beyond AC110V ~ 240V voltage, and ensure reliable grounding
4. Please do not switch frequently, so as not to affect the normal service life of the laser lamp. 5: Do not touch the lens of the laser projection window with your hand, so as not to affect the use effect.
5. In case of failure, please ask professional personnel for maintenance. Do not disassemble the lamp without authorization.
6. According to the use environment, clean the lens regularly to ensure the light efficiency

Please note: artificial damage or tear warranty label, are not within the scope of warranty! Please refer to the warranty details

Power consumption table of laser lamp:

Laser range and coverage:

The projection range is a square size of H* H, as shown in the figure

The length of H = projection distance * 0.93
0.93 is the scanning coefficient of plus or minus 25 degrees. If the scanning parameter is plus or minus 20 degrees, the coefficient needs to be changed to 0.73

Contents displayed on the display, comparison table of various functions

Auto

| show| Classification of program groups

0 is recommended

step| For the sub programs in each folder, when cycle is selected, all sub programs

will be played

rate| Pattern movement speed. The higher the value, the faster the movement speed.

It is recommended to set it equal to 20

Sound

| show| Classification of program groups

0 is recommended

step| For the sub programs in each folder, when cycle is selected, all sub programs

will be played

Sensitivity| Adjust the control sensitivity of the sound
clear| Learn to adapt and filter out special noise in the environment
DMX:1~512| type| DMX512 18CH/25CH
Start add| address code
  Slave

| Slave mode| When DMX interfaces are connected to each other, they follow the actions of the host (self-propelled playback, sound control, SD list and storage

list are played with the host)

SD List

| show| The folders in SD card are classified program groups. When cycle is selected,

the programs under all folders will be played in cycle

file| For the sub programs under each folder, when cycle is selected, the sub

programs in the current folder will be played in cycle

mode| Program in SD card, automatic and sound control switching
rate| The larger the value, the slower the picture moves
  ExFlash

| show| View program class storage order
file| View sub program storage order
mode| Automatic and voice controlled switching
rate| The larger the value, the slower the picture moves

Setting

| Scan-speed| Scan parameter setting
DB25-ilda -XY| Adjust ILDA X, Y positive and negative, and adjust whether to automatically

recognize the insertion of DB25 pin parallel port line

XY| X and Y direction setting, sizing. This setting is invalid when using

external ILDA interface input

Color| Color and brightness adjustment
FFT/sound| Sound control action parameter adjustmen
SD| SD card playback parameter regulator
DMX| DMX parameter adjustment will affect 22 channel performance in 25 channel

mode

Catch DMX| Not open, function temporarily reserved
Safe THR| Single point residence time setting, the larger the value, the better the

protection effect and the safer

Shutter use| Detect DB25 pin parallel port (13th pin)
interpolate| Enabled by default to prevent gaps in mobile graphics, which will affect

the performance of channel 22 in 25CH mode

  Device

| Language/语言| English / Chinese
Closed time| Set the on time of the LCD
RESET Parameter| Restore factory settings

DMX Channel table

18CH

CH2

|

Model

| 0-49| Auto (0<CH3<250，pattern)(CH3=>250，Loop Playback)
50-99| Sound(0<CH3<250，pattern) (CH3=>250，Loop Playback)
100-149| count down
150-200| animation
201-255| Geometric beam
CH3| gobo /frame| 0-249| pattern
250-255| Sound control or auto loop animation

CH4

| Strobe| 0-10| No Strobe
11-199| Flash by frequency
200-255| Sound control flashing

CH5

|

color

| 0-1| Fixed color
2-15| 7 solid colors （detail with in below Table18）
16-19| Automatic change of 7 solid colors
20-33| 7 colors（detail with in below Table18）
34-37| 7 kinds of color automatic change
38-154| Color segment（detail with in below Table18）
155-255| Color segment flow

CH6

|

Line & surface

| 0-63| Show as faceted effect
64-127| Plane dot display effect
128-191| Segmented display
192-255| Only point and line effects

CH7

|

X move

| 0-125| Manually adjust the X position
126-185| Automatic cyclic movement in X direction
186-225| Automatic jumping movement in X direction
226-245| Automatic irregular jump in X direction
246-255| Sound control X-direction irregular jump

CH8

|

Y move

| 0-125| Manually adjust the Y position
126-185| Automatic cyclic movement in Y direction
186-225| Automatic jumping movement in Y direction
226-245| Automatic irregular jump in Y direction
246-255| Sound control Y-direction irregular jump

CH9

|

Zoom

| 0-10| No zoom
11-87| Manually zoom
88-150| Auto zoom in
151-200| Auto zoom out
201-255| Cycle zoom in and zoom out

CH10

|

X_zoom

| 0| No zoom
1-128| Manual zoom in X direction
129-255| Auto zoom in X direction

CH11

|

Y_zoom

| 0| No zoom
---|---|---|---
1-128| Manual zoom in Y direction
129-255| Auto zoom in Ydirection

CH12

|

rotate

| 0| Stop rotation
1-128| Manual rotation
129-192| Automatic clockwise rotation
193-255| Automatic counter clock rotation

CH13

|

depiction

| 0-10| no depiction
10-74| Manually hide and add
75-104| Automatic depiction (The higher the value, the faster the speed)
105-144| Auto hide     (The higher the value, the faster the speed)
145-184| Auto paint and hide      (The higher the value, the faster the speed)
185-224| Automatic cycle painting1 (The higher the value, the faster the speed)
225-255| Automatic cycle painting2(The higher the value, the faster the speed)

CH14

|

X wave

| 0-9| No X wave
10-69| X Small wave
70-129| X Middle wave
130-189| X larger wave
190-255| X max wave

CH15

|

Y wave

| 0-9| No Y wave
10-69| Y Small wave
70-129| Y Middle wave
130-189| Y larger wave
190-255| Y max wave
CH16| red| 0-255| 0 = 100%,       255 = 0%
CH17| green| 0-255| 0 = 100%,       255 = 0%
CH18| blue| 0-255| 0 = 100%,       255 = 0%

Table18(TTL)

To        : green，blue，yellow，cyan，purple，white，red

22–23| 2 step| From: red，green，blue，yellow，cyan，purple，white

To        : blue，yellow，cyan，purple，white，red，green

24–25| 3 step| From: red，green，blue，yellow，cyan，purple，white

To        : yellow，cyan，purple，white，red，green，blue

26–27| 4 step| From: red，green，blue，yellow，cyan，purple，white

To        : cyan，purple，white，red，green，blue，yellow

28–29| 5 step| From: red，green，blue，yellow，cyan，purple，white
 |  |  | To        : purple，white，red，green，blue，yellow，cyan
---|---|---|---
30–31| 6 step| From: red，green，blue，yellow，cyan，purple，white

To        : white，red，green，blue，yellow，cyan，purple

32–33| 7 step| From: red，green，blue，yellow，cyan，purple，white

To        : red，green，blue，yellow，cyan，purple，white

25CH

CH2

|

Model

| 0-4| close
5-49| Auto (0<CH3<250，pattern)(CH3=>250，Loop Playback)
50-99| Sound(0<CH3<250，pattern) (CH3=>250，Loop Playback)
100-149| count down
150-200| animation
201-255| Geometric beam
CH3| gobo /frame| 0-249| pattern
250-255| Sound control or auto loop animation
CH4| Automatic playback

speed

| 0-4| Default speed
5| Speed 0, forbidden
6-255| 5 = slow, 255 = fast. (interval 5)
CH5| In Color| 0-3| Fixed color
4-6| Color change, CH5 and CH7 are pushed here, and the overall color change

can be realized through CH6

7-9| Solid color, CH5 and CH7 are pushed here, and the overall solid color change can be realized through CH6
10-127| Color segment（detail with in below Table25）
128-191| Discoloration 1| For analog laser,  please refer  to the color table in  SD

card: 64 colors; For TTL lasers, see color table: table25

192-255| Discoloration 2
CH6| Color Drawing| 0-63| Manually Fade Out| Fade In The fade color is determined by the “CH5” channel Fade Out The fade color is determined by the “CH7” channel
64-127| Manually Fade In
128-159| Auto Fade Out
160-191| Auto Fade in
192-223| Cycle auto fade in and out 1
224-255| Cycle auto fade in and out 2
CH7| Out Color| 0-3| Fixed color
4-6| Color change, CH5 and CH7 are pushed here, and the overall color change

can be realized through CH6

7-9| Solid color, CH5 and CH7 are pushed here, and the overall solid

color change can be realized through CH6

10-127| Color segment（detail with in below Table25）
128-191| Solid color| For analog laser,  please refer  to the color table in SD

card: 64 colors; For TTL lasers, see color table: table25

192-255| colour
CH8| Move X| 0| 0%, Middle pos
1-255| 1 = -100%, 127 = 0%, 255 = 100%
CH9| auto Move X| 0-84| Front to end
85-169| End to front
170-255| End to end loop
CH10| Move Y

Y

| 0| 0%, Middle pos
---|---|---|---
1-255| 1 = -100%, 127 = 0%, 255 = 100%
CH11| auto Move Y| 0-84| Front to end
85-169| End to front
170-255| End to end loop
CH12| scale| 0-127| Size, 0 = 100%, 127 = 1%
128-169| Zoom bigger
170-211| Zoom small
212-255| Zoom Big-small loop
CH13| center rotate| 0-127| Rotate, 1= 5 degree , 128 = 720 degrees
128-191| reverse rotation
192-255| forward rotation
CH14| X zoom

Twist

| 0-127| Manual zoom in X direction
128-191| Auto zoom in X direction
192-255| Twist in X direction
CH15| X zoom

Twist

| 0-127| Manual zoom in Y direction
128-191| Auto zoom in Y direction
192-255| Twist in Y direction
CH16| X Wave| 0-127| Manually adjust the amplitude| period and amplitude setting by ch18(Wave ref)
128-191| X forward wave
192-255| X reverse wave
CH17| Y Wave| 0-127| Manually adjust the amplitude| period and amplitude setting by ch18(Wave ref)
128-191| Y forward wave
192-255| Y reverse wave
CH18| Wave ref period and amplitude| 0-63| 1 period wave
64-127| 2 period wave
128-191| 3 period wave
192-255| 4 period wave
CH19| Show Point

Line&surface

| 0-9| Default display
10-129| The number of points is 30 ~ 4. The larger the value, the lower the brightness. The fewer the value, the higher the

brightness

130-191| point number： 16
192-255| point number： 8
CH20| Strobe| 0-2| No strobe
3-255| Flash by frequency
CH21|

Array

| 0| no
1-63| 1 graph 8 position| X or Y movement may be affected (9-12 channels), depending on the array position, and the multi graph array will accelerate the

original movement speed.

64-127| 2 graphs 4 position
128-175| 3 graphs 3 position
176-255| 4 graphs 2 position
CH22| Border| 0-63| Have subdivide

with interpolate

| Eliminate visible gaps in end joints
64-127| Real time
128-191| Have subdivide with

interpolate

192-255| Real time
CH23| red| 0-255| 0 = 100%,      255 = 0%
---|---|---|---
CH24| green| 0-255| 0 = 100%,      255 = 0%
CH25| blue| 0-255| 0 = 100%,      255 = 0%

Table25(TTL)

To        : green，blue，yellow，cyan，purple，white，red

202–211| 2 step| From: red，green，blue，yellow，cyan，purple，white

To        : blue，yellow，cyan，purple，white，red，green

212–221| 3 step| From: red，green，blue，yellow，cyan，purple，white

To        : yellow，cyan，purple，white，red，green，blue

222–231| 4 step| From: red，green，blue，yellow，cyan，purple，white

To        : cyan，purple，white，red，green，blue，yellow

232–241| 5 step| From: red，green，blue，yellow，cyan，purple，white

To        : purple，white，red，green，blue，yellow，cyan

242–242| 6 step| From: red，green，blue，yellow，cyan，purple，white

To        : white，red，green，blue，yellow，cyan，purple

252–255| 7 step| From: red，green，blue，yellow，cyan，purple，white

To        : red，green，blue，yellow，cyan，purple，white

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>