MARCY MWM-7119 68kg 150lb Stack Home Gym Owner’s Manual
- June 5, 2024
- marcy
Table of Contents
- MARCY MWM-7119 68kg 150lb Stack Home Gym Owner’s Manual
- BEFORE YOU BEGIN
- IMPORTANT SAFETY NOTICE
- EXERCISE GUIDELINES
- Beginning a Strength Building Program
- WARNING LABEL PLACEMENT
- IMPORTANT ASSEMBLY INFORMATION
- OPERATION NOTES
- CARE AND MAINTENANCE
- WEIGHT CAPACITY AND DIMENSION
- EXPLODED DIAGRAM
- Combination Lock Set Up Instruction
- IMPEX® INC. LIMITED WARRANTY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
MARCY MWM-7119 68kg 150lb Stack Home Gym Owner’s Manual
BEFORE YOU BEGIN
Thank you for selecting the MARCY HOME GYM MWM-7119 by IMPEX® INC. For your safety and benefit, read this manual carefully before using the equipment. As a manufacturer, we are committed to provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory. To avoid unnecessary delays, please call our TOLL-FREE customer service number. Our Customer Service Agents will provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. – Fri. 9 a.m. – 5 p.m. PST www.marcypro.com
support@impex-fitness.com
IMPORTANT SAFETY NOTICE
This exercise equipment is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your equipment. In particular, note the following safety precautions:
-
Keep children and pets away from the equipment at all times. DO NOT leave children unattended in the same room with the equipment.
-
Only one person at a time should use the equipment.
-
If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY. -
Position the equipment on a clear, leveled surface. DO NOT use the equipment near water or outdoors.
-
Keep hands away from all moving parts.
-
Always wear appropriate workout clothing when exercising. DO NOT wear robes or other clothing that could become caught in the equipment. Running or aerobic shoes are also required when using the equipment.
-
Use the equipment only for its intended use as described in this manual. DO NOT use attachments not recommended by the manufacturer.
-
Do not place any sharp object around the equipment.
-
Disabled person should not use the equipment.
-
Before using the equipment to exercise, always do stretching exercises to properly warm up.
-
Never operate the equipment if the equipment is not functioning properly.
-
A spotter is recommended during exercise.
-
This equipment is designed and intended for home and consumer use only, not for commercial use.
WARNING :
BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS
ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-
EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR
PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE
INSTRUCTIONS.
EXERCISE GUIDELINES
Building Muscle and Gaining Weight
Unlike aerobic exercise, which emphasizes endurance training, anaerobic
exercise focuses on strength training. A gradual weight gain can occur while
building the size and strength of muscles. While developing muscle mass, your
body adapts to the stress placed upon it. You can modify your diet to include
foods such as meat, fish and vegetables. These foods help muscles recover and
replenish important nutrients after a strenuous workout.
Muscle Strength and Endurance
To achieve the greatest benefit from exercise, it is important to develop an
exercise program that allows you to work all of the major muscle groups
equally.
To increase muscles strength; follow this principle:
Increasing resistance and maintaining the number of repetitions of an exercise results in increased muscle strength. To tone your body, follow the principle: Decreasing resistance plus increasing the number of repetitions of an exercise results in increased body tone.
Once you feel comfortable with an exercise, you can change the resistance, the number of repetitions, or the speed at which you do the exercise. It is not necessary to change all three variables. For example, let’s say that you are training at 50 lb / 22.5 kg and performing the exercise 10 times in 3 minutes. When this becomes too easy, you may decide to move up lifting 60 lb / 27 kg for the same number of repetitions in the same amount of time. Lifting more weights fewer times most often develops muscle strength. To gain both muscle strength and endurance, it is recommended that you perform each exercise 15 to 20 reps per set.
Training Intensity
How hard you begin to train depends on your overall level of fitness. The
soreness you experienced can be lessened by decreasing the load you place on
your muscles and by performing fewer sets. To avoid injury, you should
gradually work into an exercise program and set the load to your individual
fitness level. The load should increase as your fitness level increases.
Muscle soreness is common, especially when you first start exercising. If you
are painfully sore for a long time, it may be time to change your program.
Eventually, your muscle system will become accustomed to the stress and strain
placed on it.
Beginning a Strength Building Program
Warming Up
To begin strength training, it is important to stretch and perform light
exercise for 5 to 10 minutes. This helps prepare the body for more strenuous
exercise by increasing circulation, raising your body temperature and
developing more oxygen to your muscles.
Workout
Each workout to keep in mind that muscle soreness that lasts for a long period
in not desirable and may mean that injury has occurred.
Cool Down
At the end of each workout, perform slow stretching exercises for 5 to 10
minutes. Ease into each stretch only going as far as you can. This stage
allows your muscles wind down after training.
To provide a total workout program it is also recommended that 2 to 3 days of
aerobic exercise is performed in addition to the strength training.
Drinking Water
For the body to function properly, it must be properly hydrated. If you are
exercising, you should increase your fluid intake. The reason for this is that
the water you take in will leave your system through the sweating mechanism
that cools your body during exercise. The water you lose through exercise must
be replaced so that the muscles can recover properly.
Rest Day
Although you may not feel like doing it, taking a rest day at least once a
week is important because it gives your body a chance to heal itself.
Continuously working your muscle will result in over training which will not
benefit in the long run.
WARNING LABEL PLACEMENT
The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-999-8899 for replacements. Apply the labels in the location shown.
IMPORTANT ASSEMBLY INFORMATION
-
❖ Tools Required for Assembling the Bench: Two Adjustable Wrenches and Allen Wrenches.
-
❖ NOTE :
It is strongly recommended that this equipment is assembled by two or more people to avoid possible injury. -
❖ Ensure Carriage Bolts are inserted through the SQUARE holes on components that need to be assembled. Attach washer only to end of the Carriage Bolt.
-
❖ Use Allen Bolts or Hex Bolts inserted through the ROUND hole on components that need to be assembled.
-
❖ Always wait until all bolts are assembled onto the bench before tightening the bolts. Do not tighten each bolt right after it is installed
Fasten Nuts and Bolts
Securely tighten all Nuts and Bolts after all components have been assembled
in current and previous steps.
NOTE :
Do not over tighten any component with pivoting function. Make sure all
pivoting components are able to move freely.
Do not tighten all Nuts and Bolts in this step.
Weight Plate Installation
Slide weight plates onto Guide Rod from top to bottom. The deep groove on each weight plate needs to face front and downwards.
OPERATION NOTES
Weight Plate Selection
- Use the Weight Selector Pin to select the number of weight plates to exercise.
- Do not insert weight selector pin while the weight stack or top plate is in elevated position.
- Be certain the weight Selector Pin is completely inserted.
- Each Weight Plate weights approximately 10 lb / 4.5 kg.
- Please refer to Weight Resistance Chart page.
- Never use dumbbells or other means to increase the weight resistance. Use only weight plates provided by manufacturer.
- For safety purpose while the equipment is not in use. Insert the Lock Pin into the hole on Guide Rod and use Combination Lock to lock the Pin to prevent the movement of Weight Plates. Please refer to the Combination Lock set up.
Cable Tension Adjustment
Adjust the tension of the Cable System by moving the position of lower Pulley
on the two Double Floating Pulley Brackets. If the tension is too loose, move
the lower pulley up by one hole.
If the tension is too tight, move the lower pulley down by one hole.
Front Press and Butterfly Exercises
- Insert the Butterfly Lock Pin through the holes on Front Press Base and Butterfly to lock the Butterfly in position when doing Front Press exercises.
- Pull out the Butterfly Lock Pin when doing Butterfly exercises.
WARNING
Please ensure to step with both feet on the included foot- plate while performing lower pulley exercises to avoid any unwanted movement of the exercise machine.
CARE AND MAINTENANCE
- Lubricate moving parts with WD-40 or light oil periodically.
- Inspect and tighten all parts before using the equipment.
- The equipment can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT use solvents.
- Examine the equipment regularly for signs of damage or wear.
- Replace any defective components immediately and/or keep the equipment out of use until repair.
- Failure to examine regularly may affect the safety level of the equipment.
WEIGHT CAPACITY AND DIMENSION
- Maximum user weight: 300 lbs. (136 kg)
- Assembled Dimension: 68” x 36” x 79” (1727.2mm x 914.4mm x 2007mm)
PART NO | DESCRIPTION | SIZE | SIZE (Metric) | Qty |
---|---|---|---|---|
1 | Upper Frame | 1 | ||
2 | Vertical Frame | 1 | ||
3 | Base Frame | 1 | ||
4 | Rear Stabilizer | 1 | ||
5 | Leg Developer Holder | 1 | ||
6 | Seat Support | 1 | ||
7 | Leg Developer | 1 | ||
8 | Front Press Base | 1 | ||
9 | Right Butterfly | 1 | ||
10 | Left Butterfly | 1 | ||
11 | Front Press Handle | 2 | ||
12 | Butterfly Cable Bracket | 2 | ||
13 | Arm Curl Stand | 1 | ||
14 | Swivel Pulley Bracket | 2 | ||
15 | Angled Double Floating Pulley Bracket | 1 | ||
16 | Weight Stack Cover | 1 | ||
17 | Guide Rod | 2 | ||
18 | Lat Bar | 1 | ||
19 | Selector Rod | 1 | ||
20 | Bracket | 1 ¾” x 4 ¾” | 45 mm x 120 mm | 4 |
21 | U-shaped Bracket | 2” x 7” | 51 mm x 178 mm | 1 |
22 | Lock Knob | 1 | ||
23 | Foam Tube | 2 | ||
24 | Backrest Board | 1 | ||
25 | Seat Pad | 1 | ||
26 | Arm Curl Pad | 1 | ||
27 | Large Foam Roll | Ø 1⅞”x Ø 8⅝” | Ø 48 mm x 220 mm | 2 |
28 | Foam Roll | Ø ⅞” x Ø 7” | Ø 22 mm x 180 mm | 4 |
29 | Weight Stack Cover Bracket | 2 | ||
30 | Double Floating Pulley Bracket | 2 | ||
31 | Rear Stabilizer End Cap | 2 | ||
32 | Weight Selector Pin | 1 | ||
33 | Chain | 1 | ||
34 | C-clip | 2 | ||
35 | Selector Stem | 1 | ||
36 | Weight Plate | 14 | ||
37 | Bushing | Ø1” | Ø 25 mm | 8 |
38 | Front Press Axle | 3” | 75 mm | 1 |
39 | Butterfly Axle | 2⅝” | 66 mm | 2 |
40 | Leg Developer Axle | 1 | ||
41 | Weight Plate Rubber Bumper | Ø2⅜”x 1” | Ø 61 mm x 25 mm | 2 |
42 | Pulley | 16 | ||
--- | --- | --- | --- | --- |
43 | Pulley Bushing | Ø ⅞”x ½” | Ø 22 mm x 14 mm | 14 |
44 | Rubber Bumper | Ø1⅞”x 2 ½” | Ø 44 mm x 64 mm | 1 |
45 | Rubber Bumper | Ø1 ½” x ⅝” | Ø 37 mm x 16 mm | 1 |
46 | Butterfly Lock Pin | 2 | ||
47 | Ankle Strap | 1 | ||
48 | Upper Cable | 116” | 2960 mm | 1 |
49 | Butterfly Cable | 91” | 2330 mm | 1 |
50 | Lower Cable | 134” | 3420 mm | 1 |
51 | Cone-shaped End Cap | Ø1” | Ø 25 mm | 1 |
52 | End Cap | 2” x 2” | 50 mm | 3 |
53 | End Cap | Ø 2” | Ø 50 mm | 7 |
54 | End Cap | Ø1” | Ø 25 mm | 4 |
55 | Carriage Bolt | M10 x 2 ¾” | M10 x 70 mm | 10 |
56 | Allen Bolt | M10 x 2 ¾” | M10 x 70 mm | 9 |
57 | Allen Bolt | M10 x 2 ½” | M10 x 65 mm | 2 |
58 | Allen Bolt | M10 x 2” | M10 x 50 mm | 2 |
59 | Allen Bolt | M10 x 1 ¾” | M10 x 45 mm | 9 |
60 | Allen Bolt | M10 x ¾” | M10 x 20 mm | 13 |
61 | Allen Bolt | M8 x 2 ¾” | M8 x 70 mm | 2 |
62 | Allen Bolt | M8 x ⅝” | M8 x 16 mm | 6 |
63 | Allen Bolt | M6 x 3/5” | M6 x 16 mm | 8 |
64 | Philips Screw | M6 x ⅝” | M6 x 16 mm | 2 |
65 | Washer | Ø ¾” | Ø 10 mm | 50 |
66 | Washer | Ø ⅝” | Ø 8 mm | 8 |
67 | Washer | Ø ½” | Ø 6 mm | 10 |
68 | Spacer | Ø 1” x Ø ⅜” | Ø 25 mm x Ø 11 mm | 6 |
69 | Aircraft Nut | M10 | 41 | |
70 | Aircraft Nut | M6 | M6 | 2 |
71 | Self Tapping Screw | ST5 x ⅜” | ST5 x 10 mm | 2 |
72 | Lock Pin | 1 | ||
73 | Combination Lock | 1 | ||
74 | Cable Retainer | 2 | ||
75 | Handle Grip | 2 | ||
76 | Foam Roll Cover | 4 |
EXPLODED DIAGRAM
Combination Lock Set Up Instruction
The Lock is set at the manufacturer to the open at 0-0-0 (all zeros are
positioned in the middle). It is recommended to change the combination to
ensure safety.
Please follow the below steps to change the combination:
- Push and hold the combination adjustment button (#1) as indicated below, while holding down the adjustment button, turn the numerical dial (#2) to set the desired combination in the middle. Release the button (#1). Set the two other numerical dials the same way. This only needs to be done once.
- To lock, turn the dials so the Lock shows random numbers.
- To unlock, turn the dials to the combination setup in step one, press the shackle (#3) to open.
MWM-7119 WEIGHT RESISTANCE CHART
Weight Plate| Front Press| Butterfly| Lat Pull| Low Pulley
Lb.| Kg.| Lb.| Kg.| Lb.| Kg.| Lb.| Kg.
1| 31| 14.1| 15| 6.8| 30| 13.4| 30| 13.4
2| 44| 20| 20| 9| 40| 17.9| 40| 17.9
3| 57| 25.9| 25| 11.2| 50| 22.4| 50| 22.4
4| 70| 31.8| 30| 13.4| 60| 26.9| 60| 26.9
5| 83| 37.7| 35| 15.6| 70| 31.4| 70| 31.4
6| 96| 43.6| 40| 17.8| 80| 35.9| 80| 35.9
7| 109| 49.5| 45| 20| 90| 40.4| 90| 40.4
8| 122| 55.4| 50| 22.2| 100| 44.9| 100| 44.9
9| 135| 61.3| 55| 24.4| 110| 50.4| 110| 50.4
10| 148| 67.2| 60| 26.6| 120| 54.9| 120| 54.9
11| 161| 73.1| 65| 28.8| 130| 60.4| 130| 60.4
12| 174| 79| 70| 31| 140| 64.9| 140| 64.9
13| 187| 84.9| 75| 33.2| 150| 70.4| 150| 70.4
14| 200| 91| 80| 35.4| 160| 74.9| 160| 74.9
Note : Each plate weights 10 lb. (4.53 kg) Numbers are approximate. Actual weights may vary. Values for Butterfly are for each arm.
IMPEX® INC. LIMITED WARRANTY
IMPEX Inc.
(“IMPEX®”) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of two years
on the Frame from the date of purchase. This warranty extends only to the
original purchaser. IMPEX’s obligation under this Warranty is limited to
replacing or repairing, at IMPEX’s option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes. No other warranty beyond that specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential
damages arising out of or in connection with the use or performance of the
product or other damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyments or use, costs of removal,
installation or other consequential damages or whatsoever natures. Some
states/provinces do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and
any implied warranties of merchantability or fitness for a particular purpose
is limited in its scope and duration to the terms set forth herein. Some
states/provinces do not allow limitations on how long an implied warranty
lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights
which vary from states/provinces to states/provinces.
AUSTRALIA:
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
Register on-line at www.marcypro.com
IMPEX® INC.
2801 S. Towne Ave.
Pomona, CA 91766
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department
toll-free at 1-800-999-8899 during our
regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time. support@impex-fitness.com When ordering replacement parts, always give the following
information.
- Model
- Description of Parts
- Part Number
- Date of Purchase
References
- Fitness.com
- Inicio | Costco México
- The Best Home Gyms, Cardio and more - impex-fitness.com
- Get the Best Home Exercise Equipment / Marcy Pro
- Get the Best Home Exercise Equipment / Marcy Pro
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>