GS99 Marcy Dual Stack Multi Gym Instruction Manual
- May 15, 2024
- marcy
Table of Contents
MARCY DUAL STACK
HOME MULTI GYM
GS 99
Retain This Manual for Reference
01092016
OWNER’S MANUAL
NOTE: Please read all instructions carefully before using thisproduct
BEFORE YOU BEGIN
Thank you for selecting the MARCY DUAL STACK GS-99 CORNER GYM. For your safety
and benefit, read this manual carefully before using the machine. As a
manufacturer, we are committed to provide you complete customer satisfaction.
If you have any questions, or find there are missing or damaged parts, we
guarantee you complete satisfaction through direct assistance from our
factory. To avoid unnecessary delays, please contact our Customer Solutions
Department.
Pure-Tec Limited
www.puretecfitness.com
Email:service@puretecfitness.com
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain
precautions apply whenever you operate a piece of exercise equipment. Be sure
to read the entire manual before you assemble or operate your machine. In
particular, note the following safety precautions:
- Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine.
- Only one person at a time should use the same station.
- If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
- Position the machine on a clear, leveled surface. DO NOT use the machine near water or outdoors.
- Keep hands away from all moving parts.
- Always wear appropriate workout clothing when exercising. DO NOT wear robes or other clothing that could become caught in the machine. Running or aerobic shoes are also required when using the machine.
- Use the machine only for its intended use as described in this manual. DO NOT use attachments not recommended by the manufacturer.
- Do not place any sharp object around the machine.
- Disabled person should not use the machine without a qualified person or physician in attendance.
- Before using the machine to exercise, always do stretching exercises to properly warm up.
- Never operate the machine if the machine is not functioning properly.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN.
THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS
WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY
FITNESS EQUIPMENT. PURE-TEC LIMITED ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
HARDWARE PACK
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches
NOTE: It is strongly recommended two or people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Place the Right Base Frame (#1) on a flat surface. Make sure there is
enough space around to assemble the machine.
B.) Insert four Guide Rods (#9) into the holes on the Right Base Frame (#1).
Secure each Guide Rod to the Right Base Frame from the bottom with a M10 x 1”
Allen Bolt (#81).
C.) Slide four Ø 2 ½” x 1” Rubber Bumpers (#75) onto the Guide Rods. STEP 2
(See Diagram 2)
A.) Attach the Rear Vertical Frame (#4) to the Right Base Frame (#1). Attach
the Left Base Frame (#2) to the Rear Vertical Frame. Align the holes and
secure them with two M10 x 2 ¾” Carriage Bolts (#84), ∅ ¾” Washers (#99), and
M10 Aircraft Nuts (#96).
B.) Do not tighten the Nuts and Bolts yet. STEP 3 (See Diagram 3)
A.) Attach the Right Vertical Beam (#3) to the Right Base Frame (#1). Secure
it with two M10 x 2 ½” Carriage Bolts (#85), ∅¾” Washers (#99), and M10
Aircraft Nuts (#96). Do not tighten the Nuts and Bolts yet.
B.) Attach the Right Seat Support (#7) to the Right Vertical Beam (#3). Secure
it with one M10 x 2 ½” Carriage Bolt (#85), one M10 x 2 3/8” Allen Bolt (#83),
one 3 1/8” x 1 ¾” Bracket (#31), two Ø ¾” Washers (#99), and one M10 Aircraft
Nut (#96).
C.) Attach the Right Seat Support (#7) to the Right Base Frame (#1). Secure it
with one M10 x 2 ½” Carriage Bolt (#85), ∅ ¾” Washer (#99), and M10 Aircraft
Nut (#96).
D.) Attach the Leg Developer (#19) to the bracket on the Right Seat Support
(#7). Secure it with one M10 x 2 7/8” Allen Bolt (#79), two Ø ¾” Washers
(#99), and one M10 Aircraft Nut (#96). Do not over tighten the Leg Developer,
make sure it is able to swivel. STEP 4 (See Diagram 4)
A.) Slide fourteen Weight Plates (#44) onto the rear set of Guide Rods
(#9). Make sure the groves on the Plates all face toward the back of the
machine. Insert a Selector Rod (#29) into the center holes. Slide a Selector
Stem (#45) onto the two Guide Rods.
B.) Repeat Procedure A above to install the other fourteen Weight Plates onto
the other two Guide Rods. Make sure the grove on the Plate all face toward the
front of the machine.
C.) Place the Upper Frame (#6) onto the Right Vertical Beam (#3), Guide Rods
(#9), and the Rear Vertical Frame (#4).
D.) Secure the Upper Frame (#6) to the Right Vertical Beam (#3) with two M10 x
2 ½” Carriage Bolts (#85), one 4 3/8” x 1 ¾” Bracket (#73), two Ø ¾” Washers
(#99), and two M10 Aircraft Nuts (#96).
E.) Secure the Upper Frame to each Guide Rod with one M10 x 1” Allen Bolt
(#81) and Ø ¾” Washer (#99).
F.) Attach the Left Vertical Beam (#5) to the Left Base Frame (#2). Secure it
with two M10 x 2 ½” Carriage Bolts (#85), Ø ¾” Washers (#99), and M10 Aircraft
Nuts (#96).
G.) Secure the Left Vertical Beam (#5) to the Upper Frame (#6) and Rear
Vertical Frame (#4) with two M10 x 2 ¾” Carriage Bolts (#84), Ø ¾” Washers
(#99), and M10 Aircraft Nuts (#96).
H.) DO NOT tighten all Nuts and Bolts yet. STEP 5 (See Diagram 5)
A.) Attach the Left Seat Support (#8) to the Left Vertical Beam (#5). Secure
it with two M10 x 2 ½” Carriage Bolts (#85), one 4 3/8” x 1 ¾” Bracket (#73),
two Ø ¾” Washers (#99), and two M10 Aircraft Nuts (#96).
B.) Attach the Left Seat Support (#8) to the Left Base Frame (#2). Secure it
with a M10 x 2 ½” Carriage Bolt (#85), Ø ¾” Washer (#99), and M10 Aircraft Nut
(#96).
C.) Attach the Leg Press Frame (#14) to the Left Base Frame (#2). Secure it
with one M12 x 3 ¾” Hex Bolt (#89), two Ø1” Washers (#100), and one M12
Aircraft Nut (#97).
D.) Attach the Leg Press Adjustment Frame (#15) to the Leg Press Plate (#28).
Secure it with one M10 x 2 ½” Carriage Bolt (#85), Ø ¾” Washer (#99), and M10
Aircraft Nut (#96).
E.) Insert the Leg Press Adjustment Frame (#15) into the opening on the Leg
Press Frame (#14).
Use a M18 Lock Knob (#61) to secure it at desired position. STEP 6 (See
Diagram 6)
A.) Attach the Front Press Base (#10) to the Right Base Frame (#1). Secure it
with one M10 x 9 ¼” Front Press Axle (#49), two Ø ¾” Washers (#99), and two
M10 Aircraft Nuts (#96).
B.) Attach two Front Press Frames (#13) onto the bracket on the Front Press
Base. Secure them to the Front Press Base with four M10 x 2 ½” Carriage Bolts
(#85), Ø ¾” Washers (#99), and M10 Aircraft Nuts (#96).
C.) Securely tighten all Nuts and Bolts previously installed. STEP 7 (See
Diagram 7)
A.) Attach the Butterfly Support Frame (#11) to the front of Right Vertical
Frame (#3). Attach the Butterfly Pulley Support (#12) to the back of Right
Vertical Frame. Align the holes and secure them with two M10 x 2 ½” Carriage
Bolts (#85), Ø ¾” Washers (#99), and M10 Aircraft Nuts (#96).
B.) Attach two Swivel Pulley Brackets (#23) to the Butterfly Pulley Support
(#12). Secure each Bracket with one M12 x 4 3/8” Hex Bolt (#88), two Ø1”
Washers (#100), and one M12 Aircraft Nut (#97). Do not over tighten the nut
and bolt. The brackets need to swivel.
C.) Insert the Axle on the Right Butterfly (#18) through a Butterfly
Adjustment Frame (#26) into the hole on the Butterfly Support Frame (#11).
Secure it with one Ø1 ½” Washer (#101), Lock Ring (#53), M6 x 1 ¼” Allen Bolt
(#93), and M6 Aircraft Nut (#95).
D.) Thread a T-shaped Pull Pin (#58) through the hole on the Right Butterfly.
Use the Pin to adjust the Butterfly position.
E.) Attach a Butterfly Arm Pad (#35) to the Right Butterfly. Secure it with
two M8 x 2 3/8” Allen Bolts (#91) and Ø 5/8” Washers (#98).
F.) Repeat procedures C, D and E above to install the Left Butterfly. STEP 8
(See Diagram 8)
A.) Attach the Vertical Press Frame (#20) to the Rear Vertical Frame (#4).
Secure it with one M10 x 4 7/8” Vertical Press Axle (#48), two Ø ¾” Washers
(#99), and two M10 x 5/8” Allen Bolts (#80).
B.) Place the Vertical Press Frame rest against the rubber bumper on the Left
Vertical Beam (#5).
CABLE LOOP DIAGRAM
STEP 9 (See Cable Loop Diagram & Diagram 9)
A.) Attach the 108” Upper Cable (#37) to the front opening on the Upper Frame
(#6). Attach a Pulley (#56) to the opening. Secure it with one M10 x 2 3/8”
Allen Bolt (#83), two Pulley Bushings (#55), and one M10 Aircraft Nut (#96).
Draw the Cable towards the back of the machine. Note: Make sure the Ball
Stopper is underneath the frame.
B.) Attach a Pulley to the bracket on the Upper Frame. Secure it with one
M10x1 ¾” Allen Bolt (#82), two ∅¾” Washers (#99), one 2 7/8” L-shaped Pulley
Bracket (#50), and one M10 Aircraft Nut (#96). Pull the Cable over the Pulley
then downward. Install a Pulley to a Flat Double Floating Pulley Bracket
(#25). Let the bracket hanging for now.
C.) Draw the Cable around the Pulley then upward to the second open bracket on
the Upper Frame. Install another Pulley with a U-shaped Pulley Bracket (#51).
D.) Draw the Cable around the Pulley then downward to the Selector Rod (#29).
Securely thread the end of the Cable through the Weight Selector Pin (#46)
into the Selector Rod. Use the Nut at the end of the Cable to tighten down the
Bolt. STEP 10 (See Cable Loop Diagram & Diagram 10)
A.) Clip one end of the 106” Butterfly Cable (#38) to the slot on the Left
Butterfly Adjustment Frame. Draw the Cable through the slot then to the open
left Swivel Pulley Bracket (#23).
B.) Attach a Pulley (#56) to the bracket. Secure it with one M10 x 1 ¾” Allen
Bolt (#82), two ∅ ¾” Washers (#99), and one M10 Aircraft Nut (#96).
C.) Draw the Cable around the Pulley then downward. Install a Pulley to the
Angled Double Floating Pulley Bracket (#24). Install another Pulley then let
the Bracket hanging for now.
D.) Draw the Cable upward to the right Swivel Pulley Bracket. Install another
Pulley.
E.) Draw the Cable to the Right Butterfly Adjustment Frame and secure the end
of the cable to the slot.
STEP 11 (See Cable Loop Diagram & Diagram 11)
A.) Attach the 239” Front Press Cable (#36) to the lower opening on the Leg
Developer (#19).
Attach a Pulley (#56) to the opening. Secure it with one M10 x 2 3/8” Allen
Bolt (#83), two Pulley Bushings (#55), and one M10 Aircraft Nut (#96).
B.) Draw the Cable underneath the Pulley to the opening on the bottom of Right
Seat Support (#7). Attach a Pulley to the opening and secure it with one M10 x
1 ¾” Allen Bolt (#82), two Ø ¾” Washers (#99), and one M10 Aircraft Nut (#96).
C.) Draw the Cable underneath the Pulley then through the bottom opening on
the Right Vertical Beam (#3) to the second open bracket on the Right Base
Frame (#1).
D.) Attach a Pulley to the second open bracket. Secure it with one M10 x 1 ¾”
Allen Bolt (#82), two ∅ ¾” Washers (#99), and one M10 Aircraft Nut (#96).
E.) Draw the Cable around the Pulley then upward to the Flat Double Floating
Pulley Bracket (#25) previously installed in Step-9. Install a Pulley to the
Bracket on the selected hole.
Note: After completing the entire cable installations, come back to this step
and check the tightness of the cable loop system. If the cables are too loose,
move up the pulley on the bracket. If the cables are too tight, move down the
pulley on the bracket.
F.) Draw the Cable around the Pulley then down to the first open bracket on
the Right Base Frame (#1). Install a Pulley with a U-shaped Pulley Bracket
(#51).
G.) Draw the Cable around the Pulley then upward to the Angled Double Floating
Pulley Bracket (#24) previously installed in Step-10. Install a Pulley to the
selected hole on the Bracket. Adjust the tension of the cables by changing the
Pulley position on the Bracket.
H.) Draw the Cable around the Pulley then down to the open bracket on the back
of Right Vertical Beam (#3). Install a Pulley with a 2 7/8” L-shaped Pulley
Bracket (#50).
I.) Draw the Cable through the opening on the Right Vertical Beam to the open
bracket on the back of the Front Press Base (#10). Install a Pulley.
J.) Draw the Cable around the Pulley then back to the lower opening on the
Right Vertical Beam. Install a Pulley to the opening with one M10 x 2 3/8”
Allen Bolt (#83), two Pulley Bushings (#55), and one M10 Aircraft Nut (#96).
K.) Draw the Cable back to the opening on the Front Press Base. Install a
Pulley to the opening with one M10 x 8 ¼” Allen Bolt (#87), two Ø ¾” Washers
(#99), and one M10 Aircraft Nut (#96).
L.) Draw the Cable back to the open bracket welded on the lower Right Vertical
Beam. Secure the end of the Cable to the bracket with one M10 x 1” Allen Bolt
(#81), two Ø ¾” Washers (#99), and one M10 Aircraft Nut (#96). STEP 12 (See
Diagram 12)
A.) Attach end of the 357” Leg Press Cable (#39) to the bracket on the Left
Seat Support (#8). Secure the Cable to the bracket with one M10 x 1” Allen
Bolt (#81), two Ø ¾” Washers (#99), and one M10 Aircraft Nut (#96).
B.) Draw the Cable to the upper open bracket on the Leg Press Frame. Attach a
Pulley to the bracket. Secure it with one M10 x 1 3/4” Allen Bolt (#82), two ∅
¾” Washers (#99), and one M10 Aircraft Nut (#96).
C.) Draw the Cable around the Pulley then to the open bracket on the Left Seat
Support (#8). Attach a Pulley to the opening. Secure it with one M10 x 1 ¾”
Allen Bolt (#82), two Ø ¾” Washers (#99), and one M10 Aircraft Nut (#96).
D.) Draw the Cable around the Pulley then back to the lower open bracket on
the Leg Press Frame. Repeat Procedure B above to install a Pulley.
E.) Draw the Cable around the Pulley then to the lower opening on the Left
Seat Support. Install another Pulley and secure it with one M10 x 2 3/8” Allen
Bolt (#83), two Pulley Bushings (#55), and one M10 Aircraft Nut (#96).
F.) Draw the Cable underneath the Pulley then through the bottom of Left
Vertical Beam to the first open bracket on the Left Base Frame.
G.) Install a Pulley with one M10 x 1 ¾” Allen Bolt (#82), two ∅ ¾” Washers
(#99), and one M10 Aircraft Nut (#96).
H.) Pull the Cable upward to the front opening on the Vertical Press Frame
(#20). Install a Pulley with one M10 x 5 ¾” Allen Bolt (#86), two Ø ¾” Washers
(#99), and one M10 Aircraft Nut (#96).
I.) Draw the Cable around the Pulley then downward to the second open bracket
on the Left Base Frame. Repeat Procedure G above to install a Pulley.
J.) Pull the Cable upward to the back opening on the Vertical Press Frame.
Repeat Procedure H above to install a Pulley.
K.) Draw the Cable around the Pulley then downward to the third open bracket
(angled) on the Left Base Frame. Repeat Procedure G above to install a Pulley.
L.) Pull the Cable upward and connect to the Short Chain (#77) with a C-clip
(#78). Note:
After completing the entire Cable installations, check the tightness of the
Cables, if the Cables are too loose, shorten the Chain. If the Cables are too
tight, lengthen the Chain.
M.) Connect the Chain to the 61”Vertical Press Cable (#40) with a M10 x 1”
Allen Bolt (#81), two Ø ¾” Washers (#99), and one M10 Aircraft Nut (#96).
N.) Draw the Cable to the bracket on the top of Upper Frame (#6). Install two
Small Pulleys (#57) to the bracket with two 2 3/8” L-shaped Pulley Brackets
(#52).
O.) Draw the Cable over the Small Pulleys then downward. Securely threaded it
through the Weight Selector Pin (#46) into the Selector Rod (#29).
P.) Use the Nut on the Bolt at the end of the Cable to securely tighten the
Bolt to the Selector Rod. STEP 13 (See Diagram 13)
A.) Place a Seat Pad (#32) onto the Seat Incline Adjustment (#16). Secure it
with two M8 x 1 5/8” Allen Bolts (#92) and Ø 5/8” Washers (#98).
B.) Insert the Seat Incline Adjustment into the opening on the Left Seat
Support. Secure it with a M18 Lock Knob (#61) at desired position.
C.) Attach a Backrest Board (#33) to the Left Vertical Beam (#5). Secure it
with two M8 x 2 3/8” Allen Bolts (#91) and ∅ 5/8” Washers (#98). STEP 14
(See Diagram 14)
A.) Place a Seat Pad (#32) onto the Right Seat Support (#7). Secure it with
two M8 x 2 3/8” Allen Bolts (#91) and ∅ 5/8” Washers (#98).
B.) Attach a Backrest Board (#33) to the Right Vertical Beam (#3). Secure it
with two M8 x 2 3/8” Allen Bolts (#91) and ∅ 5/8” Washers (#98).
C.) Insert two Foam Roll Tubes (#41) halfway through the holes on the Right
Seat Support (#7) and Leg Developer (#19). Push four Foam Rolls (#47) onto the
Tubes from both sides. Plug four Foam Roll End Caps (#62) into the ends.
D.) Attach the Arm Curl Pad (#34) to the Arm Curl Stand (#21). Secure it with
two M8 x 5/8” Allen Bolts (#90) and ∅ 5/8” Washers (#98). Insert the Arm Curl
Stand into the opening in front of the seat. Use the M18 Lock Knob (#61) to
secure the desired position.
E.) Connect the Lat Bar (#22) to the Upper Cable with two C-clips (#78) and a
Short Chain (#77).
F.) Connect the Arm Curl Handle (#42) to the Front Press Cable (#36) with two
C-clips (#78) and a Long Chain (#104). STEP 15 (See Diagram 15)
A.) Securely tighten all the nuts and bolts previously installed.
B.) To maximize the performance of the gym, it is recommended to use light
lubricant such as WD-40 on the two chromed rods which the weight plates slide
up and down to minimum frictions.
C.) Attach four Weight Stack Covers (#30) to the machine and secure each
Weight Stack Cover with two M10 x 5/8” Allen Bolts (#80) and ∅ 3/4” Washers
(#99).
PARTS LIST
KEY NO. | DESCRIPTION | Q’ty |
---|---|---|
1 | Right Base Frame | 1 |
2 | Left Base Frame | 1 |
3 | Right Vertical Beam | 1 |
4 | Rear Vertical Frame | 1 |
5 | Left Vertical Beam | 1 |
6 | Upper Frame | 1 |
7 | Right Seat Support | 1 |
8 | Left Seat Support | 1 |
9 | Guide Rod | 4 |
10 | Front Press Base | 1 |
11 | Butterfly Support Frame | 1 |
12 | Butterfly Pulley Support | 1 |
13 | Front Press Frame | 2 |
14 | Leg Press Frame | 1 |
15 | Leg Press Adjustment Frame | 1 |
16 | Seat Incline Adjustment | 1 |
17 | Left Butterfly | 1 |
18 | Right Butterfly | 1 |
19 | Leg Developer | 1 |
20 | Vertical Press Frame | 1 |
21 | Arm Curl Stand | 1 |
22 | Lat Bar | 1 |
23 | Swivel Pulley Bracket | 21 |
24 | Angled Double Floating Pulley Bracket | 1 |
25 | Flat Double Floating Pulley Bracket | 2 |
26 | Butterfly Adjustment Frame | 8 |
27 | Ø1 ½” x 7/8” Bushing | 1 |
28 | Leg Press Plate | 2 |
29 | Selector Rod | 4 |
30 | Weight Stack Cover | 1 |
31 | 3 1/8” x 1¾” Bracket | 2 |
32 | Seat Pad | 2 |
33 | Backrest Board | 1 |
34 | Arm Curl Pad | 2 |
35 | Butterfly Arm Pad | 1 |
36 | 239” Front Press Cable | 1 |
37 | 108” Upper Cable | 1 |
38 | 106” Butterfly Cable | 1 |
39 | 357” Leg Press Cable | 1 |
40 | 61” Vertical Press Cable | 1 |
41 | Foam Tube | 2 |
42 | Arm Curl Handle | 1 |
43 | Arm Curl Handle Tube | 1 |
44 | Weight Plate | 28 |
45 | Selector Stem | 2 |
46 | Weight Selector Pin | 2 |
47 | Foam Roll | 4 |
48 | M10 x 4 7/8” Vertical Press Axle | 1 |
49 | M10 x 9 ¼” Front Press Axle | 1 |
50 | 2 7/8” L-shaped Pulley Bracket | 2 |
51 | U-shaped Pulley Bracket | 2 |
52 | 2 3/8” L-shaped Pulley Bracket | 2 |
53 | Lock Ring | 2 |
54 | 1 5/8” Rubber Bumper | 1 |
55 | Pulley Bushing | 8 |
56 | Pulley | 26 |
57 | Small Pulley | 2 |
58 | T-shaped Pull Pin Set | 2 |
59 | 2” Sleeve | 2 |
60 | 1¾” Sleeve | 1 |
61 | M18 Lock Knob | 3 |
62 | Foam Roll End Cap | 4 |
63 | 2” x 1” End Cap | 4 |
64 | 1” Square End Cap | 4 |
65 | 1½” Square End Cap | 3 |
66 | 1 7/8” Square End Cap | 16 |
67 | Handle Grip | 6 |
68 | Lat Bar Grip | 2 |
69 | Ø1½” x 1” Bushing | 2 |
70 | Ø 1” x Ø ½” Bushing | 2 |
71 | Ø1” x Ø 7/8” Bushing | 12 |
72 | ؾ” x Ø 3/8” Bushing | 2 |
73 | 4 3/8” x 1%” Bracket | 2 |
74 | Ø1 7/8” x 1 5/8” Rubber Bumper | 2 |
75 | Ø2½” x 1” Rubber Bumper | 4 |
76 | Ø1½” x 5/8” Rubber Bumper | 1 |
77 | Short Chain | 2 |
78 | C-clip | 5 |
79 | M10 x 2 7/8” Allen Bolt | 1 |
80 | M10 x 5/8” Allen Bolt | 10 |
81 | M10 x 1” Allen Bolt | 11 |
82 | M10x 1¾” Allen Bolt | 21 |
83 | M10 x 2 3/8” Allen Bolt | 5 |
84 | M10 x 2 ¾” Carriage Bolt | 4 |
85 | M10 x 2 ½” Carriage Bolt | 18 |
86 | M10 x 5 ¾” Allen Bolt | 2 |
87 | M10 x8 ¼” Allen Bolt | 1 |
88 | M12 x 4 3/8” Hex Bolt | 2 |
89 | M12 x 3 ¾” Hex Bolt | 1 |
90 | M8 x 5/8” Allen Bolt | 2 |
91 | MB x 2 3/8” Allen Bolt | 10 |
92 | M8 x 1 5/8” Allen Bolt | 2 |
93 | M6 x1 ¼” Allen Bolt | 2 |
94 | M6 x 5/8” Philips Screw | 3 |
95 | M6 Aircraft Nut | 2 |
96 | M10 Aircraft Nut | 56 |
97 | M12 Aircraft Nut | 3 |
98 | Ø5/8” Washer | 14 |
99 | ؾ” Washer | 95 |
100 | Ø1” Washer | 6 |
101 | Ø1½” Washer | 2 |
102 | Ankle Strap | 1 |
103 | Single Handle | 1 |
104 | Long Chain | 1 |
105 | Ø1” Cone-shaped End Cap | 2 |
#6 Allen Wrench (Tool) | 1 | |
#5 Allen Wrench (Tool) | 1 |
GS 99 WEIGHT RESISTANCE CHART
| WEIGHT PLATE
---|---
Station| 1| 2| 3| 4| 5| 6| 7
Low Pulley| 16| 20| 25| 30| 34| 38| 43
Lat Pull| 7| 12| 16| 20| 25| 30| 34
Butterfly| 5| 8| 11| 14| 17| 20| 24
Leg Press| 27| 36| 45| 55| 64| 73| 82
Front Press| 16| 23| 30| 36| 44| 50| 57
Vertical Press| 9| 14| 16| 18| 20| 23| 27
| WEIGHT PLATE
---|---
Station| 8| 9| 10| 11| 12| 13| 14
Low Pulley| 48| 52| 57| 62| 66| 70| 75
Lat Pull| 39| 43| 48| 52| 57| 62| 66
Butterfly| 33| 36| 40| 43| 46| 49| 52
Leg Press| 91| 100| 109| 118| 127| 136| 145
Front Press| 64| 71| 77| 84| 91| 98| 105
Vertical Press| 32| 36| 41| 45| 50| 55| 59
Numbers are shown in kgs and are approximate.
Actual weight may vary.
*Value for butterfly is for each arm.
LIMITED WARRANTY
Pure-Tec. warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. Please refer to
www.puretecfitness.com for warranty conditions. This warranty extends only to
the original purchaser and is valid for home use only. Pure-Tec’s obligation
under this Warranty is limited to replacing damaged or faulty parts at Pure-
Tec’s option.
All returns must be pre-authorised by Pure-Tec. This warranty does not extend
to any product or damage to a product caused by or attributable to freight
damage, abuse, misuse, improper or abnormal usage, purchasers own repairs or
for products used for commercial or rental purposes. No other warranty beyond
that specifically set forth above is authorised by Pure-Tec.
Pure-Tec is not responsible or liable for indirect, special or consequential
damages arising out of or in connection with the use or performance of the
product or other damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyments or use, costs of removal,
installation or other consequential damages or whatsoever natures.
The warranty extended hereunder is in lieu of any and all other warranties and
any implied warranties of merchantability or fitness for a particular purpose
is limited in its scope and duration to the terms set forth herein.
Your statutory rights are not affected.
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by contacting our Customer Solutions
Department, www.puretecfitness.com
Email:service@puretecfitness.com
When ordering replacement parts, please give the following information,
- Model
- Description of Parts
- Part Number
- Date of Purchase
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>