soundmaster FUR6005 Radio Alarm Clock FM Black Instructions

: June 5, 2024
: soundmaster

Table of Contents

soundmaster FUR6005 Radio Alarm Clock FM Black
ENVIRONMENTAL PROTECTION
FUNCTION AND CONTROLS
INTRODUCTION
GETTING START
INFRARED SENSOR FUNCTION
Resetting
Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

soundmaster FUR6005 Radio Alarm Clock FM Black

ENVIRONMENTAL PROTECTION

Do not dispose of this product with the normal household waste at the end of its life cycle. Return it to a collection point for the recycling of electrical and electronic devices. This is indicated by the symbol on the product, user manual or packaging The materials are reusable according to their markings. By reusing, recycling or other forms of utilization of old devices and packaging you make an important contribution to the protection of our environment. Please contact your local authorities for details about collection points.

WARNING

To reduce the risk of electric shock, do not remove the cover (or back). There are no user-serviceable parts inside. Refer servicing to qualified service personnel. This symbol indicates the presence of dangerous voltage inside the enclosure, sufficient enough to cause electric shock. This symbol indicates the presence of important operating and maintenance instructions for the device Used batteries are hazardous waste and NOT to be disposed of with the household waste! As a consumer you are legally obligated to return all batteries for environmentally responsible recycling – no matter whether or not the batteries contain harmful substances) Return batteries free of charge to public collection points in your community or shops selling batteries of the respective kind. Only return fully discharged batteries ) marked Cd = cadmium, Hg = mercury, Pb = lead

Only use mercury and cadmium-free batteries.
Used batteries are hazardous waste and NOT to be disposed of with the household waste!!!
Keep batteries away from children. Children might swallow batteries.
Contact a physician immediately if a battery was swallowed.
Check your batteries regularly to avoid battery leakage.
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION: Danger of explosion if battery is incorrectly replaced
Replace only with the same or equivalent type

WARNING

DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Safety, Environmental and Setup Instructions

Use the device in dry indoor environments only.
Protect the device from humidity.
This apparatus is for moderate climates areas use, not suitable for use in tropical climates countries.
No objects filled with liquids, such as vases, shall be placed on the apparatus.•
The mains plug or an appliance coupler is used as the disconnect device, the disconnect devices shall remain readily operable.
Connect this device to a properly installed and earthed wall outlet only. Make sure the mains voltage corresponds with the specifications on the rating plate.
Make sure the mains cable stays dry during operation. Do not pinch or damage the mains cable in any way.
A damaged mains cable or plug must immediately be replaced by an authorized service center.
In case of lightning, immediately disconnect the device from the mains supply.
Children should be supervised by parents when using the device.
Clean the device with a dry cloth only.
Do NOT use CLEANING AGENTS or ABRASIVE CLOTHS!•
Do not expose the device to direct sunlight or other heat sources.
Install the device at a location with sufficient ventilation in order to prevent heat accumulation.
Do not cover the ventilation openings!
Install the device at a safe and vibration-free location.
Install the device as far away as possible from computers and microwave units; otherwise radio reception may be disturbed.
Do not open or repair the enclosure. It is not safe to do so and will void your warranty. Repairs only by authorized service/ customer center.
No naked flame sources, such as lighted candles, should be placed on the unit.
When you are necessary to ship the unit store it in its original package. Save the package for this purpose.
In case of malfunction due to electrostatic discharge or fast transient (burst), remove and reconnect the power supply.
If the unit is not using for a long period of time, disconnect it from the power supply by unplugging the power plug. This is to avoid the risk of fire.

FUNCTION AND CONTROLS

INFRARED SENSOR
PROJECTION UNIT
PROJECTION ON/OFF
PROJECTION TIME 180°
. VOLUME UP / DISPLAY AUTO CHANGE ON-OFF
CLK.ADJ. / MEMORY / MEMORY+ / NAP /
MEMORY-
ALARM 1 ON-OFF SET
ALARM 2 ON-OFF SET
<< / TUNE –
>> / TUNE + / YEAR/MONTH/DAY
VOLUME DOWN / DSIPALY AUTO ON-OFF
SNOOZE / SLEEP / DIMMER
ON – OFF RADIO / ALARM OFF
PM INDICATOR
STANDBY INDICATOR
ALARM 1 INDICATOR
RCC ANTENNA TOWER ICON INDICATOR
ALARM 2 INDICATOR
DISPLAY
SPEAKER
FOCUS ADJUSTMENT FOR PROJECTION UNIT
FM ANTENNA
RADIO CONTROLLED CLOCK ANTENNA
BATTERY COMPARTMENT
AC POWER CORD
RATING LABEL

INTRODUCTION

The unit is designed to automatically synchronize its current time and date with radio signal generated from DCF 77 Frankfurt, Germany.

Power connection
Plug the AC power cord to a household outlet AC source. This unit is equipped with a battery backup system, it requires a 3V CR2032 flat lithium battery (not included). Insert the battery in the battery compartment, making certain that the positive and negative (+ and -) battery terminals are attached to the corresponding terminals on the plate in the battery compartment. If an AC power failure occurs, the clock automatically switches to the battery power supply, the clock and timer memory continue running. When the AC power resumes, the clock switches back to AC again.

GETTING START

Plug the AC power cord to a household outlet AC source.

The unit will display full segment for two seconds, then it will enter the normal mode.
Display will lighten up.
The unit will start searching radio controlled clock signal automatically.
The display radio-controlled clock Antenna tower will flash.
Automatically stop after 10 minutes if fail in receiving.
N ote :
During automatic time search, the device is only conditionally operable (switchable on /off).
Auto search can be stopped by pressing snooze button (13) for 3 seconds.

DISPLAY IN GOOD RECEPTION MODE

The radio controlled clock Antenna tower icon will keep displaying. DISPLAY IN POOR RECEPTION MODE
The radio controlled clock Antenna tower icon will turn off.

NOTE: It will take 3-10 minutes to complete. For best results, place the radio-controlled clock antenna (24) away from metal or electrical objects and near a window with a clear view to the sky.
SETTING WITH RADIO-CONTROLLED:
Not necessary as it is automatically adjusted.
SETTING WITHOUT RADIO CONTROLLED MANUAL SETTING:
Can be done when radio controlled clock antenna tower icon is turned off by pressing SNOOZE button (13) for 3 seconds.
TIME AND CALENDAR MANUAL SETTING
Setting Time and Calendar

A. Press CLK.ADJ. (6) button in standby mode and keep depress over 3 seconds to enter time set mode, after enter the setting mode, press CLK.ADJ. button (6) to change the mode cycle as follows
Normal → Year → Month → Day → 12/24 H → Real time Hour → Real time Min → Normal

Action (during data adjustment):

Press << / Tune – button (10) to adjust data backward.
Press >> / Tune + button (11) to adjust data forward.
Keep depress << or >> button for 3 seconds to enable auto-forward.

Press the alarm set button (8/9) during normal mode to show the alarm time. Afterwards keep depress the alarm set button (8/9) over 2 seconds to enter the alarm set mode. After enter the setting mode, press the alarm set button (8/9) to change the mode cycle as follow:

Normal → AL 1 Hour → AL 1 Min → AL 1 weekday Alarm → AL 1 wake beep → AL 1 wake radio → AL 1 wake radio volume → Normal.
Normal → AL 2 Hour → AL 2 Min → AL 2 weekday Alarm → AL 2 wake beep → AL 2 wake radio → AL 2 wake radio volume → Normal.
Select alarm weekday mode as follows
1-5 : Monday to Friday
1-7 : Whole week
6-7 : Saturday & Sunday
1-1 : One day of week

Action (during data adjustment):

Press << / Tune – button (10) to adjust data backward.
Press >> / Tune + button (11) to adjust data forward.
Keep depress << or >> button for 2 seconds to enable auto forward.

Enable/disable the Alarm
Press and hold the “ALARM 1” (8) / “ALARM 2” (9) button to enable or disable the alarm. Once the alarm is activated, the bell symbol will be appeared on the display.

Alarm duration and snooze function:
Alarm Duration – Beep alarm or radio alarm will continue output for 30 minutes if no key press, then it will stop automatically and wait for same alarm time on next day.

Action for Snooze:

During alarming, press the Snooze button (13) will enable snooze function, Beep alarm or Radio alarm will stop.
Snooze interval is 9 minute (not include second offset)
Snooze will continue unless press ON/OFF button (14) to alarm off of Buzzer alarm or Radio Alarm stop automatically after 30 minutes.

Display Auto on-off function:

Press & hold the display auto on-off button (12) for 3 seconds, the LED display standby Indicator will light on, the LED display will turn off after 15 seconds automatically, Press any button to maintain the LED display for 15 seconds.
Press & hold the display auto on-off button (12) for 3 seconds, the LED display standby Indicator will light off to cancel this function.

Auto change display content:
In radio off mode, press & hold the display auto change on/off button (5) for 3 seconds to enter time display auto change mode. to display the time and press again to display Month/Day, the display returns to time display after 5 seconds.

Listening to Radio

Press the ON/OFF button (14) to turn the unit on.
Use the Tune + or Tune – button to select the desired radio station. If you press and hold the Tune + or Tune – button for one second, the release, the unit will automatically scan to the next broadcasting station.
Press the ON/OFF button (14) to turn the radio OFF.

To set / recall the radio presets

Press the ON/OFF button (14) to turn the unit ON.
Use the Tune + or Tune – button to select the desired radio station.
Press and hold the memory / memory + button; “P01” will blink in the display.
Use the Tune+ or Tune- button to select the desired preset station (P01-P10)
Press the memory / memory + button again to set the preset.
Repeat steps 2 through 5 to set more presets.
The unit can preset 10 stations totally for FM.
When “P01-P10” is blinking, press the Tune+ or Tune- button to select the preset number.
When recalling preset stations, press memory / memory + button to select the preset number.

Note :
– Ensure that the FM antenna is completely unrolled and extended for best FM reception.

Sleep operation
When listening to radio, press Sleep button (13) to enter sleep mode. You can just adjust the sleep timer from 90 mins to 15 mins by pressing the Sleep button (13). The unit will automatically turn off after the selected time.

Dimmer control
In standby mode, press the dimmer (13) button allows you to set the brightness of the LED display to high, medium, low 3 levels.

NAP timer function (count down timer)
During radio off mode, press the NAP button (6), to turn on the NAP mode, the NAP time will keep by 5 seconds, within 5 seconds and press NAP button (6) button can change the duration from 90 min – 10 min.
The alarm buzzer will sound for 30 min and then shut off automatically. To stop the alarm buzzer, press the ON/OFF button (14).
Press the NAP button (6) has no effect during alarm operation. Press ON/OFF button (14) to cancel NAP function.

Projection unit

Focus setting: Adjust the projection clock brightness/focus by turning the brightness/focus adjustment wheel unit the projected time is clearly shown on the ceiling or wall.
Adjust projected direction.
To flip projected image by 180°, press PROJECTION TIME 180° FLIP button (4).

NOTE: PROJECTS TIME IMAGE ON THE CEILING OR WALL OF A DARKENED ROOM. MAXIMUN PROJECTION DISTANCE IS 3-9 FEET.

IMPORTANT
There is a sensor located on top of the unit that picks up any movement or objects near the top or back of the unit. Please be sure to place the radio on a surface with a no obstructions 9-12 inches above or 3-6 inches behind the unit. This will help maximize the area for recognizing the motion of your hand and also reduce the chances of the unit false triggering. If the unit begins beeping and the display functions erratically, it may be either too close to an object above or behind the unit. If this happens, please make sure there are 9-12 inches of clearance above and 3-6 inches behind the unit to avoid the false triggering.

INFRARED SENSOR FUNCTION

In radio off mode, to display alarm time settings :
Wave your hand over the IR SENSOR (1) again within 1 second to show the ALARM 1 time.
Wave your hand over the IR SENSOR (1) again within 1 second to show the ALARM 2 time.
In radio on mode, to turn sleep function on:
Wave your hand over the IR SENSOR (1) for about 2 seconds to turn on the sleep function, the “90” minutes icon will in the LED display. Sleep time can only be set for a maximum 90 minutes. Press the SLEEP BUTTON (13) to change the sleep time as described before.
Press the ON/OFF BUTTON (14) to cancel the sleep function.
While the alarm is sounding, to turn snooze function on: Wave your hand over the IR SENSOR (1) once to activate the snooze for 9 minutes.
In radio on mode, to display the radio frequency and alarm time settings:
Wave your hand over the IR SENSOR (1) again within 1 second to show the radio frequency
Wave your hand over the IR SENSOR (1) again within 1 second to show the ALARM 1 time.
Wave your hand over the IR SENSOR (1) again within 1 second to show the ALARM 2 time.
Wave your hand over the IR SENSOR (1) again within 1 second to show the Real time.
In radio off mode, Press & hold the display auto on-off button (12) for 3 seconds, the LED display standby Indicator will light on, the LED display will turn off after 15 seconds automatically.
Wave your hand over the IR SENSOR (1) to turn the display on. Press any key button to turn display on.

Resetting

If the system does not respond or exhibits erratic or intermittent operation, you may have experienced an electrostatic discharge (ESD) or a power surge that triggered the internal microcontroller to shut down automatically. If this occurs, simply disconnect the ac power cord and remove the system backup battery, wait for at least 3 minutes and then setup the unit again as if it is a brand new unit.

Specifications

Frequency range :
Battery backup:
Power supply :
Importer
Wörlein GmbH Gewerbestrasse 12 D 90556 Cadolzburg GERMANY 87.5 – 108 MHz
3V (CR2032 Flat Lithium battery x 1) not included AC230V 50Hz
Tel.: +49 9103 71 67 0
Fax.: +49 9103 71 67 12 Email.:service@soundmaster.de Web.: www.soundmaster.de
Specifications are subject to change without further notice. Copyright by Wörlein GmbH, D 90556 Cadolzburg.