soundmaster UR620 Clock Radio with Bluetooth and USB Charging Jack Instruction Manual

UR620 Clock Radio with Bluetooth and USB Charging Jack
Instruction Manual

ENVIRONMENTAL PROTECTION

Do not dispose of this product with the normal household waste at the end of its life cycle. Return it to a collection point for the recycling of electrical and electronic devices.
This is indicated by the symbol on the product, user manual or packaging
The materials are recyclable according to their labeling. By reusing materials or other forms of recycling old devices and packaging, you are making an important contribution to protecting our environment. If necessary, remove batteries and personal data before disposal free of charge and ask your local authority about the responsible disposal point
WARNING
Risk of electric shock Do not open!
Caution: To reduce the risk of electric shock, do not remove the cover (or back). There are no user serviceable parts inside. Refer servicing to qualified service personnel.
This symbol indicates the presence of dangerous voltage inside the enclosure, sufficient enough to cause electric shock.
This symbol indicates the presence of important operating and maintenance instructions for the device
Used batteries are hazardous waste and NOT to be disposed of with the household waste! As a consumer you are legally obligated to return all batteries for environmentally responsible recycling – no matter whether or not the batteries contain harmful substances)
Return batteries free of charge to public collection points in your community or shops selling batteries of the respective kind. Only return fully discharged batteries
) marked Cd = cadmium, Hg = mercury, Pb = lead

• Only use mercury and cadmium-free batteries.
• Used batteries are hazardous waste and NOT to be disposed of with the household waste!!!
• Keep batteries away from children. Children might swallow batteries.
• Contact a physician immediately if a battery was swallowed.
• Check your batteries regularly to avoid battery leakage.
• Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• CAUTION: Danger of explosion if battery is incorrectly replaced
• Replace only with the same or equivalent type
• Use the device in dry indoor environments only.
• Protect the device from humidity.
• This apparatus is for moderate climates areas use, not suitable for use in tropical climates countries. Safety, Environmental and Setup Instructions
• No objects filled with liquids, such as vases, shall be placed on the apparatus.
• The mains plug or an appliance coupler is used as the disconnect device, the disconnect devices shall remain readily operable.
• Connect this device to a properly installed and earthed wall outlet only. Make sure the mains voltage corresponds with the specifications on the rating plate. • Make sure the mains cable stays dry during operation. Do not pinch or damage the mains cable in any way.
• A damaged mains cable or plug must immediately be replaced by an authorized service center.
• In case of lightning, immediately disconnect the device from the mains supply.
• Children should be supervised by parents when using the device.
• Clean the device with a dry cloth only.
• Do NOT use CLEANING AGENTS or ABRASIVE CLOTHS!
• Do not expose the device to direct sunlight or other heat sources.
• Install the device at a location with sufficient ventilation in order to prevent heat accumulation.
• Do not cover the ventilation openings!
• Install the device at a safe and vibration-free location.
• Install the device as far away as possible from computers and microwave units; otherwise radio reception may be disturbed.
• Do not open or repair the enclosure. It is not safe to do so and will void your warranty. Repairs only by authorized service/ customer center.
• No naked flame sources, such as lighted candles, should be placed on the unit.
• When you are necessary to ship the unit store it in its original package. Save the package for this purpose.
• In case of malfunction due to electrostatic discharge or fast transient (burst), remove and reconnect the power supply.
• If the unit is not using for a long period of time, disconnect it from the power supply by unplugging the power plug. This is to avoid the risk of fire.

LOCATION OF CONTROLS

1 POWER ON / OFF
2 SOURCE
3 BLUETOOTH / FM RADIO / AUX-IN / SLEEP LED (amber)
4 VOLUME –
5 VOLUME +
6 TUNE DOWN / HOUR
7 PLAY / RADIO PRESET
8 TUNE UP / MIN
9 ALARM BUZZER / ALARM RADIO LED (amber)
LOW BATTERY LED (red)| 10 ALARM
11 SNOOZE / BRIGHTNESS
12 SLEEP
13 TIME SET
14 BLUETOOTH PAIR
15 FM ANTENNA WIRE
16 DC IN JACK
17 LINE-IN JACK
18 USB CHARGING PORT
19 SPEAKERS
20 LED DISPLAY
21 BATTERY COMPARTMENT (bottom of unit)
---|---

INSTALLATION

Use only the supplied AC/DC-adapter (AC In – 100-240V AC, 50/60Hz / DC Out – 5V 2.0A). Do not connect the unit before checking the main voltage and before all other connections have been made.
Insert the plug from the AC/DC-adapter to the DC jack (16) of the main unit. Then connect the AC/DC-adapter to an AC outlet.
When you connect the unit at first time the display (20) will show “0:00” and start flashing.
To keep accurate time, this unit uses (2) “AAA batteries” (not included) for clock backup.
These batteries keep the clock operating in the event of a power interruption.

BACKUP BATTERY INSTALLATION

Open the battery door (21) by pushing in on the tabs, then removing the door.
Insert two (2) ‘AAA’ batteries following the correct polarity indicated in the battery compartment.
Replace the battery door (21) back on the compartment.
NOTES: The batteries are used to back-up the clock and alarm times when the AC adaptor is disconnected or there is a power failure.
Alkaline batteries are recommended for the longest backup time.
When replacing the battery, do not disconnect the AC power adapter otherwise the current time, alarm, and station presets will be erased.
When to replace the battery: The red LED of battery indicator will light up when there are no batteries or when the batteries are low.

CHANGING THE INPUT SOURCE

With the UR620 powered “ON”, repeatedly press the “SOURCE” button to change the input source to cycle between FM Radio, Bluetooth or AUX IN.

PLAYING THE RADIO

With the clock radio plugged in and powered ‘ON’, press the “SOURCE” button, then select FM and the frequency indicator will appear on the display.
Repeatedly press the “TUNE UP / MIN” or “TUNE DOWN / HOUR” button to manually adjust the tuning on the display until the desired station appears.
For auto tuning, press and hold the “TUNE UP / MIN” or “TUNE DOWN / HOUR” button until the display starts to scan then release the button and the tuner will search and stop on the next strong station. Repeat this process until the desired station appears on the display.
NOTE: Fully extend the FM wire antenna to increase reception sensitivity. Keep digital music players or mobile phones away from the FM antenna as this may cause interference. Do not place the FM antenna near the AC power adaptor as this may lead to reception interference.

SETTING RADIO PRESETS

To store a radio station to memory, first follow the steps above to tune in the desired station.
Press and hold the “PLAY/RADIO PRESET” button to create a preset for the current station.
“P” will appear and “##” (the preset number) will blink on the display.
Press the “TUNE UP / MIN” or “TUNE DOWN / HOUR” button to select a preset number (01- 10).
Press the “PLAY/RADIO PRESET” button again to confirm the setting and the station will be saved into memory. Repeat these steps for up to 10 presets, as desired.
To recall a preset station, repeatedly press the “PLAY/RADIO PRESET” button until the desired preset number appears in the display and the station tunes in.

SETTING THE CLOCK

Plug in the UR620, but leave the power “OFF”.
Press and hold the “TIME SET” button (13) until the clock flashes in the display.
Press the “TUNE DOWN / HOUR” button (6) repeatedly to set the hour, and press the “TUNE UP / MIN” button (8) repeatedly to set the minute.
Press the “TIME SET” button (13) again to store the new clock setting.
NOTES: If you do not press any button for about 10 seconds while setting the clock, the clock setting will be canceled.

SETTING THE ALARM

In standby mode, press and hold the “ALARM” button (10) and the display will begin flashing.
Press the “TUNE DOWN/HOUR” or “TUNE UP/MIN” button (6 or 8) to set the desired alarm time.
Press “ALARM” button (10) to confirm the alarm time set.
The amber LED of alarm source indicator (default as alarm radio) will blink.
Press “TUNE DOWN HOUR” or “TUNE UP / MIN” button (6 or 8) to set the desired alarm source
(Buzzer or Radio). Amber LED of the selected alarm source indicator will light up
Press “ALARM” button (10) to confirm the alarm source set, the volume level will blink on the
display (there is no volume setting if alarm source is set to Buzzer).
Press “TUNE DOWN / HOUR” or “TUNE UP / MIN” button to set the maximum alarm volume.
Press “ALARM” button (10) to confirm the alarm set.
To silence the alarm, press “ALARM” or “POWER ON / OFF” button (10 or 1).
NOTES: To deactivate the alarm, press “ALARM” button (10), the amber LED of alarm source indicator will turn off. Before setting the alarm, make sure that the clock time is set correctly (see setting the clock).
SNOOZE
When alarm sounds, pressing the “SNOOZE/ BRIGHTNESS” button (11) will temporarily silence
the alarm. The alarm will sound again after approximately 10 minutes.
To extend the snooze duration, repeatedly press the “SNOOZE / BRIGHTNESS” button (11) to cycle through and select one of the snooze presets.
NOTE: Once the snooze function has been activated, press the “SNOOZE / BRIGHTNESS” button (11) anytime and the display will show the remaining time. Repeatedly press the “SNOOZE / BRIGHTNESS” button (11) to adjust or modify the current snooze time setting.
SLEEP TIMER
The UR620 features a sleep timer to allow you to fall asleep while listening to the unit.
After the preset time duration ends, the unit will automatically shut off.
When the unit powered ON, press the “SLEEP” button (12). The amber LED of “SLEEP” indicator will light up and “15” will appear on the display briefly indicating the unit will turn off after 15 minutes.
To increase the sleep time duration, up to a maximum of 90 minutes, repeatedly press the
“SLEEP” button (12) to select one of the following sleep time presets.
With the sleep timer active, press the “SLEEP” button (12) once to view the remaining sleep time.
To cancel the sleep timer function, repeatedly press the “SLEEP” button (12) until “OFF” appears in the display.

SETTING THE BRIGHTNESS

There are three levels of display brightness available (the default setting is low). Press the “SNOOZE / BRIGHTNESS” button (11) to cycle through and select the desired setting
NOTE: Make sure that the unit is not in alarm sound status.

STREAMING AUDIO WITH BLUETOOTH® WIRELESS

You can stream audio wirelessly to Clock Radio from up to 33’ away using your smartphone tablet, laptop or other A2DP Bluetooth® enabled device.
Turn on the unit by pressing the “POWER ON/OFF” button (1).
Then press the “SOURCE” or “BLUETOOTH PAIR” button (2 or 14). The Bluetooth® LED indicator will flash.
Turn on your Bluetooth® enabled device and search for and select “UR620”.
If asked for a password, enter “0000”.
The Bluetooth® LED indicator will change from flashing to solid, indicating that your Bluetooth® device is now connected to UR620.
Press and hold the “BLUETOOTH PAIR” button (14) for 3 seconds to disconnect the Bluetooth® connection.
NOTES: If the last paired Bluetooth® audio device is powered on and within range of the speaker, the device will automatically reconnect to UR620. For the best audio performance, turn the volume all the way up on your Bluetooth® device.
If the unit fails to pair with your Bluetooth® device, go to your Bluetooth® setting menu, then select ‘UR620 “Info”. For Android device, select “Unpair”, if using an Apple OS device, select “Forget this Device”. When UR620 appears in your list of Bluetooth® devices, select it to complete pairing.
UR620 can only play audio from one source at a time. If UR620 is connected to a Line-In source, the Bluetooth® will not function. Simply unplug the 3.5mm Line-In audio  cable and press the  “SOURCE” or “BLUETOOTH PAIR” button (2 or 14) to switch to Bluetooth®
USB CHARGING PORT
The UR620 features one USB port (18) located on the rear of the unit (see “location of controls”). The USB port supports power charging of most USB devices smartphones, tables, E-readers, digital cameras and more. Use a USB cable (sold separately) to connect a rechargeable device to UR620.

AUX IN CONNECTION

Insert one end of the 3.5mm audio cable (not included) into the “LINE OUT” jack on your external device (mobile phone, MP3 player, digital media player, etc.) and the other end into the “LINE-IN” jack (17) on rear of this unit.
To listen to the external audio source, turn this unit on by pressing the “POWER ON/OFF” button (1), then power on the external audio source. Next press the “SOURCE” button (2) to select.
AUX-IN mode. The amber LED of AUX-IN indicator will light up.
Press play on the external audio source and the sound will playback through the speakers of the UR620.
NOTE: It is suggested that you unplug the audio cable when you are not listening to the external audio unit.

TECHNICAL SPECIFICATION

Power supply
Power input
Power output
Backup battery
USB output
FM range
Bluetooth version
Audio power output| : Use only the supplied power adapter
: 100-240V~ 50/60Hz 0.4A
: DC 5V 2A
: 2x 1.5V “AAA” size batteries
: DC 5V 1A
: 87.5 – 108MHz
: Version 4.2
: 2x 3W RMS
---|---

IMPORTER
Wörlein GmbH Gewerbestrasse 12 D 90556 Cadolzburg Germany
Tel.: +49 9103 71 67 0
Fax.: +49 9103 71 67 12
Email: service@soundmaster.de
Web: www.soundmaster.de
Copyright by Woerlein GmbH, 90556 Cadolzburg, www.soundmaster.de

References

• soundmaster®
• soundmaster®
• soundmaster®

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>