PROJECT X OFFROAD GB538825 Ghost Box Wireless Control Instructions

June 5, 2024
PROJECT X OFFROAD

Model No. GB538825

IMportant safety Information

  • SAVE THESE INSTRUCTIONS­ This manual contains important safety and operating instructions.
  • Before using this product, read all instructions and cautionary markings.
  • Do not expose the keypad to rain, moisture, or snow.
  • Use of an attachment not recommended or sold by the manufacturer may result in a risk of fire, electric
  • Do not operate with a damaged keypad or ghost box ­ replace it immediately.
  • Do not operate the keypad or ghost box if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified service person.
  • Do not disassemble the keypad or ghost box; take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
  • To reduce the risk of electric shock, unplug the keypad or ghost box before attempting any maintenance or cleaning. Turning off controls will not reduce this risk

info@projectxoffroad.com
866-294-9244
Mon-Sat 8 am-5 pm PST

Technical Specifications

Input Voltage: 9-16V DC
Output Voltage : 9-16V DC
Output Maximum Current: 40A @12V DC
Output Maximum Power: 480W @12V DC
Operating Temp: -22°F to 149°F
Storage Temp: -40°F to 185°F
Waterproof Rating: IP65
Wireless Frequency : Bluetooth 5.0
Wireless Range (RF Wifi): 98.4
Feet without interference or obstruction) Wireless Range (Bluetooth®): 33 Feet without interference or obstruction) The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc., and any use of such marks by ADC Solutions Auto, LLC is under license. Other trademarks and trade names are those of their respective owners.

Includes

  • 4x CONTROL MODULES
  • 2x External Antenna
  • 2x M5 Screw (L50mm)
  • 2x Washer (OD:12:7mm / ID 5.3mm)
  • 2x M5 Lock Nut
  • 1x 3M VHB Double Sided Tape
  • 4x Rubber Cap (Spare)
  • 1x Sticker Kit

Cautions

Check your state or provincial laws before installing. The vehicle owner must comply with all applicable laws.
This product is intended solely for off-road purposes. Manufacturer and Seller assume no liability for installation or use, which are solely the responsibility of the purchaser. This product is not DOT approved and is designed and intended for off-road uses only.

  1. Do not install or use the product if it, in any way, impairs the safe operation of your vehicle.
  2. Follow the manufacturer’s instructions to ensure the product is properly and safely installed.
  3. Check your state or provincial laws before installing. The vehicle owner must comply with all applicable laws.
  4. This product is intended solely for off-road purposes. Manufacturer and Seller assume no liability for installation or use, which are solely the responsibility of the purchaser.
  5. This product is not DOT approved and is designed and intended for off-road uses only.
  6. The Manufacturer and Seller are not responsible or liable for consequential, incidental, or indirect damages, whether to person or property, resulting from the installation or improper use of this product.

Warranty

This PROJECT X product carries a Limited Lifetime warranty against defects in workmanship and materials subject to the conditions and additional warranty information is available at: www.projectxoffroad.com/pages/returns- warranty
DISCLAIMER OF WARRANTIES, INCLUDING WARRANTY OF MERCHANTABILITY AND WARRANTY OF FITNESS FOR PARTICULAR PURPOSE: EXCEPT AS SPECIFICALLY SET FORTH HEREIN, NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, IS MADE AS TO THE GHOST BOX. PROJECT X AND/OR ITS AFFILIATES EXPRESSLY DISCLAIM, WITHOUT LIMITATION, ANY STATUTORY WARRANTIES AND ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
PROJECT X 2975
Red Hill Ave.,
Ste. 100, Costa Mesa,
CA 92626, USA

FCC Compliance statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or change could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and the receiver
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirements, This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals