Aquaguard Superb Water Purifier with Active Copper User Manual

Aquaguard Superb Water Purifier with Active Copper

WHY IS AQUAGUARD® PAANI KA DOCTOR?

• Trust of 15 million+ mothers^
• Owned by 1.62 lakh+ doctors
• Service within 5 kms range of wherever you are
• 21 different technologies to address 21 different water conditions across the countr
• Tested/Certified by 130+ leading national and international laboratories

THE POWER OF AQUAGUARD° SUPERB Ss

• The new Aquaguard® Superb SS inactivates and removes microbial contaminants from your water and gives you pure, sweet-tasting water.
• Aquaguard° Superb SS is tested and certified by AWRTC for the removal of disease-causing bacteria, viruses and protozoa-cysts along with other contaminants like pesticides, residual organic impurities, harmful heavy metals, arsenic and more, to give you water that is safe and healthy.
• The Aquaguard° Superb SS comes with a multi-stage enhanced purification process. This ensures that the water you drink is absolutely pure and crystal clear.
• To ensure good health to you and your family, Aquaguard Paani Ka Doctor offers you a choice to select ideal technology, based on your input water quality.

KNOW YOUR AQUAGUARD® SUPERB SS

Make sure that your Aquaguard® Superb SS is installed by a trained Eureka Forbes Service Technician only.

1. Input water must be tested for Total Dissolved Solids (TDS) and Total Hardness.
2. Install your Aquaguard® Superb SS in a dry, ventilated place.
   • Keep it away from direct sunlight, heating devices or areas below freezing temperatures.
   • You can keep it on the kitchen counter or wall mount it.
3. Ensure that the input tap water temperature is in the range of 10°C – 40°C.
   • Avoid connection to a hot water tap as it can damage the filter.
4. Make sure that the tap pressure are 0.3 kg/cm2 to 2.0 kg/cm2 in case of UV+UF and not exceed 3.0 kg/cm2 in case of RO/RO+UV-MTDS. If the input water pressure is more than the upper limit, installation of PRV (Pressure Reducing Valve) is required. If the input water pressure is less than the lower limit, installation of Booster Pump is recommended.
5. Flush filters and membrane, thoroughly and independently for 3-5 mins to remove fine particles present in the filter. This should be done before the installation of the unit.

Input Water Quality Usage Limitations:

1. If the input water iron content is more than 0.3 mg/L, use of iron remover’ is recommended as a pre-treatment.
2. If the input water turbidity is more than 5 NTU or comprises colloidal particles, use of a special filter’ is required as a pre-filter.
3. Do not install the water purifier if the TDS is more than that prescribed in the technical specifications. “Available at an extra cost.

HERE’S HOW AQUAGUARD® SUPERB RO+SS WORKS

PURIFICATION PROCESS OF AQUAGUARD® SUPERB RO+SS

Stage| Treatment| Material|
---|---|---|---
1.| i-Filter™| Multi layered Polypropylene roving wound Cartridge| such as dirt and sand from water.
2.| Chemi-block (with Built-in Particle Trap Filter™)| Dust Free Bacterio- static Activated Carbon Block|

Reduces excess chlorine, colour and organic impurities. Also absorbs bad taste and odour from the water.

3.|

Mineral Guard™++

| Micro-controller based Electronic Impulse Producer| Prevents scaling of dissolved salts like calcium and magnesium, thus, enhancing the membrane life and improving water

4.| Reverse Osmosis Cartridge| Thin Film Composite (TFC) Reverse Osmosis Membrane| Reduces TDS, hardness, pesticides and heavy metals like arsenic, lead and mercury. Eliminates micro-organisms like bacteria, viruses, protozoa and cysts.
5.| Active Copper™+^^ Cartridge| Bacterio-static Taste Enhancer with Active Copper Technology| Copper has antimicrobial, antioxidant,

also helps to provide the body with energy and is much needed for growth and development. The activated carbon removes organic components and polishes the water, giving it a sparking look, makingit pure and great to taste.

LED INDICATION CHART FOR AQUAGUARD® SUPERB RO+SS

AQUAGUARD® SUPERB RO+SS TECHNICAL SPECIFICATIONS*

For Aquaguard® SUPERB RO+SS

#| Technical Parameters|
---|---|---
1| Dimensions (W x D x H)| 328mm x 263mm x 479mm
2| Net Weight| 6.5 kg (Approx.)
3| | Reverse Osmosis

4

| ****

Filtration Syst em

| Stages of Filtration
Stage 1: i-Filter™
Stage 2: Mineral Guard™
Stage 3: Chemi-block
Stage 4: RO Membrane
Stage 5: Active Copper™ Cartridge
5| Tank Capacity (Total)| 5.5 Litres (Approx.)
ELECTRICAL SPECIFICATIONS
1| Operating Voltage Range| 150V AC to 250V AC, 50 Hz
2| Power Supply| Input: 230V AC/Output: External AC/DC Adaptor 24V DC, 2.5A
3| Power Rating| 40 Watts
RECOMMENDED INPUT WATER PARAMETERS
1| Input Water Temperature| 10°C – 40°C
2| Input Water Pressure*| Up to 3 kg/cm2
3| Input Water TDS| Up to 2,000 mg/L
4| Total Hardness| 600 mg/L (max.)

Note: Ihe performance data presented in the table iS applicable under standard laboratory conditions”.Actual performance may  vary depending on the input water quality, water pressure and condition of filters. Technical Specifications are subject to change without prior notice. input water quality/pressure/1DS are important determinants or recovery rate and rejection f presSure is higher than the maximum specied, use of pressure regulating valve is recommended. Ihe above accessory is available with our company at an additional cost. Ensure that the water tlow from the tap into the product is always more than 1.5 LPM

Warranty void if the product is not installed as per the recommendation.
Standard Test Conditions: Feed Water Quality: TDS Max: 1,000 mg/L (NaC), Pressure: 1 kg/cm, Turbidity: 1 NTU (Max), Tem perature: 25°C, Chlorine: below 0.2 mg/L, Iron: below 0.3 mg/L. Life: 6000″ Litres. Actual performance may vary based on the input water conditions especially TDS, Hardness, Pressure, Temperature & pH. Standard test conditions are valid for online water supply installation. In suction mode, the product performance may vary.

HERE’S HOW YOUR AQUAGUARD® SUPERB RO+UV+MTDS+SS WORKS

PURIFICATION PROCESS OF AQUAGUARD® SUPERB RO+UV+MTDS+SS

Treatment| Material|
---|---|---
1.| i-Filter™| Multi-layered Polypropylene roving wound Cartridge|
2.| Chemi-block (with Built-in Particle Trap Filter™)| Dust Free Bacterio- static Activated Carbon Block| Reduces excess chlorine, colour and organic impurities. Also absorbs bad taste and odour from the water.
3.| Mineral Guard™++| Micro-controller based Electronic Impulse Producer| Generates electronic impulses which prevent scaling/deposition of

chamber, thereby, ensuring the best UV penetration, through Quartz  Glass into water column and at the same time keeping essential minerals like Calcium and Magnesium intact in water.

4.| Reverse Osmosis Cartridge| Thin Film Composite (TFC) Reverse Osmosis Membrane| Reduces TDS, hardness, pesticides and heavy metals like arsenic, lead and mercury. Eliminates micro-organisms like bacteria, viruses, protozoa and cysts.
5.| Active Copper™+^^ Cartridge| Bacteriostatic Taste Enhancer with Active Copper™ Technology| ****

that help to support healthy metabolism. It also helps to provide the body with energy and is much needed for growth and development. The activated carbon removes organic components and polishes the water, giving it a sparking look, making it pure and great to taste.

6.| UV Chamber| Germicidal UV Lamp| UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses and protozoa, thereby, making it safe to drink.
7.| TDS Regulator| Mechanical Systems|

LED INDICATION CHART FOR AQUAGUARD® SUPERB RO+UV+MTDS+SS

AQUAGUARD® SUPERB RO+UV+MTDS+SS TECHNICAL SPECIFICATIONS *

For Aquaguard® SUPERB RO+UV+MTDS+SS

4

| ****

Filtration System

| Stages of Filtration
Stage 1: i-Filter™
Stage 2: Mineral Guard™
Stage 3: Chemi-block
Stage 4: RO Membrane
Stage 5: UV Chamber
Stage 6: Active Copper™ Cartridge
5| Tank Capacity (Total)| 5.5 Litres (Approx.)
ELECTRICAL SPECIFICATIONS
1| Operating Voltage Range| 150V AC to 250V AC, 50 Hz
2| Power Supply| Input: 230V AC/Output: External AC/DC Adaptor 24V DC, 2.5A
3| Power Rating| 50 Watts
RECOMMENDED INPUT WATER PARAMETERS
1| Input Water Temperature| 10°C – 40°C
2| Input Water Pressure ***| Up to 3 kg/cm 2
3| Input Water TDS **| Up to 2,000 mg/L
4| Total Hardness| 600 mg/L (max.)

Note: The performance data presented in the table is applicable under standard laboratory conditions”. Actual performance may vary depending on the input water quality, water pressure and condition of niters. echnicalpecihcations are subect to change without prior notice.

• Input water quality/pressure/TDS are important determinants of recovery rate and rejection.

pressure Is higher than the maximum specithed, use of pressure regulating valve is recommended. ihe above is always more than 1.5 LPM.

•  company at an additional cost. Ensure that the water fiow from the tap into the product

Warranty void if the product is not installed as per the recommendation.
“Standard Test Conditions: Feed Water Quality: TDS Max: 1,000 mg/L (NaCI), Pressure: 1 kg/cm, Turbidity: 1 NTU (Max.), Temperature: 25’C, Chlorine: below 0.2 mg/L, Iron: below 0.3 mg/L. Life: 6,000 Litres. Actual performance may vary based on the input water conditions especially TDS, Hardnes5, Pressure, Temperature & pH. Standard test conditions are valid for online water supply installation. In suction mode, the product pertormance may vary.

HERE’S HOW YOUR AQUAGUARD® SUPERB UV+UF+SS WORKS

PURIFICATION PROCESS OF AQUAGUARD® SUPERB UV+UF+SS

Stage| Treatment| Material|
---|---|---|---
1.| i-Filter™| Multi-layered Polypropylene roving wound Cartridge|
2.| Chemi-block (with Built-in Particle Trap Filter™)| Dust Free Bacterio- static Activated Carbon Block| Reduces excess chlorine, colour and organic impurities. Also absorbs bad taste and odour from the water.
3.| Mineral Guard™++| Micro-controller based Electronic Impulse Producer| Generates electronic impulses which prevent scaling/deposition of

thereby, ensuring the best UV penetration, through Quartz Glass into water column and at the same time keeping essential minerals like Calcium and Magnesium intact in water.

4.| Ultra Filtration| UF Hollow Fibre| Capillary tube type membrane-based technology that imparts crystal clear clarity to drinking water, in addition to making the water safe from bacteriological contamination.
5.| UV Chamber| Germicidal UV Lamp| UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses & protozoa, thereby making it safe to drink.
6.| Active Copper™+^^ Cartridge| A patented bacteriostatic taste enhancer with Active Copper™ Technology| ****

that help to support healthy metabolism. It also helps to provide the body with energy and is much needed for growth and development. The activated carbon removes organic components and polishes the water, giving it a sparkling look, making it pure and great to taste.

LED INDICATION CHART FOR AQUAGUARD SUPERB UV+UF+SS

AQUAGUARD® SUPERB UV+UF+SS TECHNICAL SPECIFICATIONS*

4

| ****

Filtration System

| Stages of Filtration
Stage 1: i-Filter™
Stage 2: Mineral Guard™
Stage 3: Chemi-block
Stage 4: UF Filter
Stage 5: UV Chamber
Stage 6: Active Copper™ Cartridge
5| Tank Capacity (Total)| 5.5 Litres (Approx.)
ELECTRICAL SPECIFICATIONS
1| Operating Voltage Range| 150V AC to 250 V AC, 50 Hz
2| Power Supply| Input: 230V AC / External AC-DC Adaptor 12V DC, 1.7 Amps
3| Power Rating| 20 Watts (max.)
4| UV Lamp| 11 Watts
5| UV Lamp Life| 8000 burning hours (as per manufacturer’s spec.)
6| Solenoid Valve| 12 V DC
RECOMMENDED INPUT WATER PARAMETERS
1| Input Water Temperature| 10°C – 40°C
2| Input Water Pressure ***| 0.3 – 2.0 kg/cm²
3| Input Iron (Max.)| 0.3 mg/L
4| Chlorine Content (Max.)| 0.2 mg/L
5| Input Water Turbidity (Max.)| 5 NTU
6| Total Dissolved Solids (TDS)| Up to 200 mg/L

Technical specifications are subject to change without prior notice.
Note: The performance data presented in the table is applicable under standard laboratory conditions”. Actual performance may vary depending on the input water quality, water pressure and condition of filters. Input water quality/pressure/TDS are important determinants ot purines performance

Warranty void if product not installed as per recommendations.
if the input water pressure is more than 2.0 kg/cm, installation of a PRV (Pressure Reducing Valve)” is mandatory. If the input water pressure is less than 0.3 kg/cm, installation of a booster pump’ is recommended. These accessories are available at an extra cOst. Standard Test Conditions 00 m Turhidity 1 NTU (Max). Temperature: 25°C, Chlorine: below O.2 mg/L, Iron: belowd. mg/t Life: 6,000 Liters. “Actual performance may vary based on the input water conditions -Turbidity and Press

MAINTAINING YOUR AQUAGUARD® SUPERB SS

• Fill the tank and disinfect the storage tank with a disinfection tablet.
• Ensure that the replacement of the consumable Cartridges are done, by a trained Eureka Forbes Service Technician, after approximately 6,000 litres of water usage or if choked.

CLEANING AND DISINFECTION OF WATER STORAGE TANK

Note: Storage Tank of this product must be periodically cleaned (at least once in every 30 days) by a disinfectant. Disinfection Tablets may be purchased from the Company Authorised service Centre. Please follow the disinfection process strictly as per the instructions as provided in this User Manual.

Switch OFF the water puriher from the main power suppiy.

• Open the top cover and push the tap lever UP to drain the tank.

• Wipe the inside of the tank with a dry, clean soft cloth.

• Keep the top cover in place

• Switch the power supply ON.
  Let the storage tank get hiled & then drop one disinfection tablet” into the tank.

• Keep the top cover in place & leave the unit for 30 mins.
  After 30 mins open the tap & discard this and the first frlling water completely. Caution: Do not drink this water

• Now your unit is ready to use
  Please ensure that this disinfection process is carried out by the authorised installation person/service technician during frst installation
  and in every subsequent mandatory servicing of your product “Available with Eureka Forbes Service Technican.

A QUICK CHECKLIST

in the tank for too long?

| Clean the storage tank.

Dispose OFF water and clean the tank.

Call an authorised Eureka Forbes service technician.

Less water has| 1. Is the tap water valve closed?

2. Is the tap water pressure too low?

3. Filters may be clogged or damaged?

| Open the tap water valve.

Call an authorised Eureka Forbes service technician.

into the storage tank

| 1. Is there water available in the overhead tank?

2. Is the main water supply tap closed?

3. Not sure what is wrong?

|

Ensure the tap is open.

Call an authorised Eureka Forbes service technician.

Water is leaking| 1. Is water coming out of the top

| Close the tap water valve, unplug the power cord

and call an authorised Eureka Forbes service technician.

IMPORTANT NOTE ON ZERO PRESSURE PUMP (ZPP) AND DRY RUN SENSOR (DRS)

Your Aquaguard® is equipped with a unique pump having both suction and boosting capabilities and comes with specially designed DRS (Dry Run Sensor). Now, this enables your Aquaguard® to work in the following operating conditions: –

• Normal Input Water Pressure – up to 3 Bar (max.)
• Low Water Pressure from Loft Tank.
• Zero water pressure
• Suction mode: Maximum 3 feet below product level
  Product functioning at Normal/ Low and Zero water Pressure

Ensure that the water flow from the tap into the product is always more than 1.5 LPM.

• In case there is no incoming water supply, the DRS detects unavailability of water and stop the unit from working to prevent dry running.

• As and when the water supply resumes, the DRS detects the availability of water and restarts the product. Meanwhle, the inteligent

• mechanism in your Aquaguard” wil keep on checking the availability of water at regular defined intervals and make the product work as and

• when water supply resumes. Note In case you notice that water in the supply line resumes and product is in stand-by mode, then please restart

• the product by switching off and ON the power supply.

• Product Functioning with Suction Capability

• The ZPP in your Aquaguard” also has the capability of suction of water from a 3 feet distance below the level of product ie, it can puill waterfroma bucket/ container

• Note: it is not suitable for suction of water from underground storage tank, pump, open wel, etc. where the water level is beyond s feet below the level of product.
  Whenever the water in the container/bucket gets over and bucket gets empty, the DRS detects non-water availability and stops the product from functioning.

• Note: When the water is rehiled in the container/bucket, the product should be restarted by switching Oft and On the power supply

• Prolonged use in loft tank mode/suction mode can impact the working of the pump, performance of the product, and life of fiters. if the performance is not meeting the flow requirement due to low input pressure, then the use of an external booster pump is highly recommended.

• Do not re-circulate/re-use the rejected water (discharged by the product) back into the product.

WARRANTY TERMS AND CONDITIONS

1. The Products are warranted against manufacturing defects for a period of twelve (12) months from the date of original purchase.

2. The Customer will notify the Company in writing promptly of any defects noticed and give the Company or its authorised agent adequate opportunity to inspect test and remedy them for which the Customer will deposit the goods at its own expense, if so, required by the Company with the Company’s Office/Service Centre along with the original invoice in the city where they are sold.

3. The Inspection and Test Report of the company’s office/service centre will be final and binding under the warranty for determining defects, repairs/alterations required or carried out or certifying work of the goods thereafter.

4. Aquaguard® may require initial setting, post-installation, depending on varying water conditions and power supply. In case of any service requirement, post-installation, please contact the company’s service centre.

5. The company or its authorised agent will be entitled to retain any defective part replaced under the warranty.

6. Notwithstanding anything to the contrary contained or implied by this warranty:

   • a) The company’s liability under this warranty shall be limited to the first sale of the goods by the company to the customer and will not apply or extend to any secondary sale of goods by the customer.

   • b) The company’s liability under this warranty shall be limited only to defects in the goods which occur under the conditions of normal operation of the goods and their proper and prescribed use. The warranty does not cover or extend to defects which are determined by the company or its authorised agents as occurring or resulting from or attributable to negligence, abuse, misuse, faulty care, operation or maintenance or repairs, alterations to the goods or any part thereof by others or the use of the goods on electrical supply for which they are not designed, or damage caused by lightening or
     other electrical disturbances or interruptions, dismantling or re-installation at a different location.

   • c) The company’s liability under this warranty shall remain valid only if the goods are duly installed by the company or its authorised agency at the location specified in the invoice and such installation is undertaken by the company or its authorised agent or franchise.

   • d) Consumable items mentioned in the consumables table are subject to normal wear and tear are not covered by this warranty. Please refer model
     specific components given in the user manual under the table ‘consumable cartridges’.

   • e) Reverse Osmosis Membrane warranty is for a period of 1 year (or) 6,000 litres (whichever is earlier) from the date of installation, on the condition
     that the input water is as per the standard test conditions for RO variants (provided in the section ‘Technical specifications table’), mentioned in the
     user manual. If the RO membrane gets clogged within warranty period, it will be cleaned/repaired/replaced free of charge as deemed fit by the
     company authorised service person/centre after inspection. (At applicable for RO models only.)

   • f) The customer will have no claim against the company, its employees and its authorised agents or franchise’s under or pursuant to this warranty in respect of death or injury to the customer or any other person or loss or damage to any property caused by or due to equipment failure, breakdown or accident, fire or operation or utilisation of the goods otherwise than in

   • g) The company’s liability, under this warranty, shall in no event and under no circumstances exceed the price paid by the customer to the company for goods stated in the invoice.

General
For the purpose of this warranty, the following expressions shall have the following meanings respectively: accordance with the user manual or by due to any other cause or circumstances beyond the control of the company.

1. The ‘Goods’ shall mean the goods described in the Order Form.
2. The ‘Customer’ shall mean the original purchaser of goods from the company.
3. The ‘Company’ shall mean EUREKA FORBES LIMITED.
4. Aquaguard® means and includes Aquaguard®,Aquaguard® Select and Sure from Aquaguard®.
5. ‘General Terms & Conditions’ shall mean the terms and conditions agreed upon by the customer and the company printed on the Order Form.
6. ‘Invoice’ shall mean the invoice issued by the company to the customer describing the goods and indicating, inter alia, the total purchase price thereof and name of the customer.
7.  ‘User Manual’ shall mean the instructions for Installation, use and maintenance provided through QR code along with Product supplied by the company.
8. EFL reserves the right, in its absolute discretion, to change, alter or discontinue and alter the terms and conditions from time to time without any prior notice.
9. Any disputes are subject to Mumbai Jurisdiction only.

Post-warranty

1. The customer may be offered a yearly Service Contract at the prevailing company rates and terms.
2. In case the customer does not wish to enter the Service Contract, he/she has the option of calling the company’s service centre having his Aquaguard® services on an actual basis, i.e., by paying the labour cost and spares needed to attend to that service/complaint call at the prevailing company rates. Such service will be rendered by the company in towns/places where the company has its service centres.
3. If during such servicing it is necessary for the company to replace or repair defective components or parts, the customer shall be required to pay for the same as per the company’s prevailing price list.
4. Eureka Forbes limited reserves the right to offer annual maintenance contract/ensure availability of spares only up to 7 years from the date of invoice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>