naxa NT-2500 25-Inch Class Widescreen FHD TV Instruction Manual

naxa NT-2500 25-Inch Class Widescreen FHD TV

Safety Information

Warning
To prevent fire and/or electric shock, do not use this plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. Do not expose this appliance to rain or moisture.

Important Safety Instructions
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Please, unplug the TV power cord when the following conditions occur:

• When there is a thunderstorm (Please, unplug the power cord and antenna).
• When cleaning the TV set.
• When the TV set is not used for a long time.
• Do not use corrosive solvents when cleaning the TV set.
• o not put the TV set in direct sunlight or near heat.
• Do not put a heat source, such as a candle or heater, on top of or near the TV set. Leave plenty of space (at least 10cm) around the TV set for ventilation.
• Place the TV set away from where it can become wet (such as near a window).
• Do not put a container with liquid (such as a vase) on top of the TV set.
• Do not move the TV set when the power is on.
• Do not touch, push, or scratch the surface of the TV set with hard materials or items. When TV surfaces are dirty, please use a wet cotton cloth or soft cloth with non-corrosive cleaners to clean it carefully. Do not use acetone, toluene or alcohol to clean the TV set. Avoid excess moisture, which can damage inner electronic components. If too much moisture is present, the TV screen may appear blurry or spotty. It is recommended that a technician install the TV set on a wall, if such placement is desired.
• An incorrect wall installation will be unsafe and hazardous.
• Do not let children climb on or play around the TV set to avoid falls, collisions, damage, and/or injuries.
• Do not hit the TV panel with hard objects.
• Do not cover the TV set with blankets or other objects when it is connected to a power source, which may cause overheating and fire.
• Batteries shall not be exposed to excessive heat such as direct sunlight, fire or the like. The power plug is used to disconnect the device. The disconnected device will not operate while unplugged.
• Apparatus with class I construction shall be connected to a electrical outlet with a protective grounding connection.

Important safety precautions

Introduction

Features

• TV uses a TFT LED display screen
• FHDTV Compatible (480i, 480p, 576i, 576p, 720p, 1080i, 1080p, 2160p)
• Supports American TV Standards 8VSB/Free 64/256QAM,NTSC System, ATSC System Connect directly to computer to achieve a TV/monitor.
• Zero X radiation complies with green environment protection requirement
• Advanced Chroma Processing
• Closed captioning/Program Control
• SAP/STEREO/MONO; ATSC.
• HDMI input
• USB input

Input terminals used for external equipment connection

• One AVinput
• One ANTENNA input
• One YPbPr input
• VGA/PC AUDIO input
• One HDMI input
• One Coxial output
• One USB input

Introduction

specification

Note: Design and specification modification maybe made at any time without prior notice; all data and dimensions are approximations.

Accessories

Please make sure the following items are included with your LED TV. If any items are missing, contact your dealer.

General Description

Overview of front and back panel

1. Remote control sensor / Power indicatorRemote control sensor / Power indicator
2. VOL +/-VOL +/- Press to increase/decrease the volume.Press to increase/decrease the volume. In the on-screen menu, use them to move left/right.In the on-screen menu, use them to move left/right.
3. CH +/-CH +/- Press to change channels.Press to change channels. 44 In the on-screen menu, use them to move up/down.In the on-screen menu, use them to move up/down.
4. MENUMENU Press to see an on-screen menu of your TV.Press to see an on-screen menu of your TV.
5. SOURCESOURCE Toggles between all the available input sourcesToggles between all the available input sources
6. STANDBYSTANDBY Press STANDBY button to toggle between normal and standby mode.Press STANDBY button to toggle between normal and standby mode.

overview of back panel

1. Power input
2. EARPHONE Connect a set of phone for private listening.
3. COXIAL Connect to a Digital Audio device.
4. AUDIO L/R Audio input for external device, such as a camcorder or VCR.
5. Y(CVBS)/Pb/Pr Connect video.
6. VGA Connect to the video output jack on your PC.
7. PC AUDIO Audio input for external devices.
8. HDMI Connect to the HDMI jack of a device with a HDMI output.
9. NTENNA INPUT Connect to an antenna or cable NTSC & ATSC.
10. USB USB input
11. Power input (DC).

OVERVIEW OF REMOTE CONTROL

1. STANDBY: Turn the TV on/off.
2. MUTE: Press to mute the sound.
3. SLEEP: Set the sleep timer.
4. FAV : Select favorite channels.
5. FAV +/- : Press to watch next / previous favorite program.
6. ADD: Add this program to the favorite channels list. ERASE: Delete this program from the favorite channels list.
7. LOCK: Press to display the Lock menu.
8. Time: Press to display current time.
9. LIST: Press to display the TV program list.
10. FREEZE: Press to freeze the screen.
11. EPG: Press to display the EPG menu.
12. INFO: Display channel information.
13. CC: Press to display the closed caption.
14. MTS: Press to select the audio channels.
15. MENU : TV system setup.
16. SOURCE : Press to change input source.
17. ARROW buttons: Use to move cursor up/down/left/right.
18. ENTER: Validation key.
19. EXIT: Press to exit menu.
20. ZOOM: Press to change the screen scale.
21.   S.MODE: Press to cycle through the different sound settings.
22. VOL +/-: Press to increase/decrease the sound level.
23. CH+/-: Press to scan through channels.
24. P.MODE: Press repeatedly to cycle through the available video picture modes.
25. Number key (0-9): Press 0-9 to select a TV channel directly when you are watching TV. The channel changes after several seconds
26. RETURN 27 26. -/–: Press this button to enter a program number for multiple program channel such as 2-1, etc.
27. RETURN: Return to the previous channel viewed.

Installing Batteries in the Romote Control

NOTE

• Batteries should last for 1 year under normal use.
• If you do not intend to use the remote control for a long period of time, remove the batteries to prevent damage due to leakage.
• Do not use old and new batteries together.
• The batteries or battery pack shall not be exposed to excessive heat such as direct sunlight, fire, or other heat sources.

External Connection

Antenna connection

Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be connected to the antenna jack directly, if the antenna cable is 300ohm parallel flat feeder cable, you need to use the 300ohm/75ohm converter to connect the antenna cable to the antenna jack. For details Please refer to the following drawing.
Antennas with 300ohm flattwins Leads Antennas with 75ohm Round Leads

CONNECTING VCR

These instructions assume that you have already oonnected your TV to an antenna or a cable TV system. Skip step 1 if you have not yet oonnected to an antenna or a cable system.

Follow the instructions in Viewing a VCR or Camoorder Tape to view your VCR tape. Each VCR has a different back panel configuration. When oonnecling a VCR, match the oolor of the oonnection terminal to the cable. We recommend the use of cables with a Ferrite Core.

1. Unplug the cable or antenna from the back of the TV.
2. Connect the cable or antenna to the ANT IN terminal on the back of the VCR.
3. Connect an RF Cable between the ANT OUT terminal on the VCR and the ANT IN terminal on the TV.
4. Connect a Video Cable between the VIDEO OUT jack on the VCR and the VIDEO IN jack on the TV.
5. Connect Audio Cables between the AUDIO OUT jacks on the VCR and the AUDIO Land AUDIO R jacks on the TV.
   • If you have a mono (non-stereo) VCR, use a Y-connector (not supplied) to hook up to the right and left audio input jacks of the TV. If your VCR is stereo, you must connect two cables.

CONNECTING DVD PLAYER SET TOP BOX

The rear panel jacks on your TV make it easy to connect a DVD to your TV.

Component video separates the video into Y {Luminance (brightness)), Pb (Blue) and Pr (Red) for enhanced video quality. Be sure to match the component video and audio connections. For example, if connecting the video cable to COMPONENT IN, connect the audio cable to COMPONENT IN also. Each DVD player/STB has a different back panel configuration.When connecting a DVD player/STB, match the color of the connection terminal to the cable. We recommend the use of cables with a Ferrite Core.

1. Connect a Component Cable between the COMPONENT IN [Y, PB, PR) jacks on the TV and the COMPONENT [Y, PB, PR) jacks on the DVD player.
2. Connect Audio Cables between the COMPONENT IN [R-AUDIO-L) jacks on the TV and the AUDIO OUT jacks on the DVD player.

CONNECTING DIGITAL AUDIO SYSTEM

The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.

CH audio is possible when the TV is connected to an external device supporting 5.1 CH. We recommend the use of cables with a Ferrite Core.

1. Connect a coxial cable between the SPDIF jack on the TV and the digital audio input jacks on the digital audio system. When a digital audio system is connected to the SPDIF terminal: Decrease the gain (volume) of the TV, and adjust the volume level with the system’s volume control.

CONNECTING USB

Connect a USB 2.0 memory device into USB slot of this TV for multimedia files playback.

1. This USB slot only supports Music (MP3) and Photo (JPG) multimedia files playback.
2. This TV is compatible with most USB devices in the market. However, we cannot guarantee the compatibility of all USB devices, due to multiple technology standards used.

Connecting DVD Player Set Top box via HDMI

This connection can only be made if there is a HDMI Output connector on the external device.

What is HDMI. HDMI, or high-definition multimedia interface, is a next- generation interface that enablesthe transmission of digital audio and video signals using a single cable without compression. Multimedia interface is a more accurate name for it especially because it allows multiplechannels of digital audio (5.1 channels). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP(High Bandwidth Digital Copy Protection) coding feature installed, and supportsmulti-channel digital audio. Each DVD player/STB has a different back panel configuration. We recommend the use of cables with a Ferrite Core.

1. Connect an HDMI Cable between the HDMI connector on the TV and the HDMI connector on the DVD player/Set-Top Box.

Connecting PC

Each PC has a different back panel configuration. The HDMI jacks do not support PC connection. We recommend the use of cables with a Ferrite Core.

1. Connect a D-Sub Cable between RGB/PC IN connector on the TV and the PC output connector on your computer.
2. Connect the PC audio input jack on the TV.

Connecting a Headphone

This connection can only be made If there Is a HOMI Output connector on the extemal device.

Plug headphone connector into headphone jack on the TV. Then the TV speaker will be muted.

Supporting signal

BASIC OPERATION

Turning The TV On and Off

How to turn the TV on or off

1. Insert the power cord plug into a polarized AC outlet.
2. Press button on remote control or STANDBY button on the LED TV.
3. Normal picture will be displayed on the screen after 6 seconds. If no signal input, “No Signal” will be displayed on the screen.
4. f temporary POWER off is required, press button on remote control or STANDBY button on the LED TV.
5. If you want to completely switch off the power for this unit, unplug the power cord from the electrical outlet.
6. After switching off the unit, do not turn on the TV again for at least 5 seconds. Status indication lamp
   No light: In power on mode.
   Red: In standby mode. Auto power off If there is no signal input in TV mode, the TV will automatically access the standby state in approximately 10 minutes. Memory before turning TV off The settings of picture and the preset channels will be memorized after turning off the unit. After restarting, the unit will work according to the mode set before being turned off.

OSD Menu OPERATION

INPUT SOURCE SELECTION

Press SOURCE button to display the input source list; Press T / ..&. button to select the input source you want to watch; Press ENTER button to enter the input source;

BASIC OPERATION

• Press MENU button on unit top or remote control to display the main menu.
• Press LEFT or RIGHT navigation button to select Picture/Audio/Time/Setup/Lock/ Channel.
• Press DOWN navigation button to enter submenu page.
• Press UP or DOWN navigation button to select the option that want to adjust.
• Press LEFT or RIGHT navigation button to adjust selected option to desired value.
• ress RIGHT navigation button or ENTER button to enter next menu page.
• ress MENU button to return to previous menu page.
• Press EXIT button to exit menu page.

FIRST TIME INSTALLATION

If this is your first time turning on this TV, Setup Wizard will appear on the screen.

• Press UP or DOWN navigation button to select preferred item.
• Press LEFT or RIGHT navigation button to adjust the value.
  Menu Language
  To choose your menu language.
  Air/Cable
  To choose your signal type: Air, Cable.
  Cable System
  To choose your Cable System: AUTO, STD, IRC, HRC.
  NOTE: Cable System is adjustable only when your signal type is set to Cable.
  Auto Scan
  Highlight Auto Scan, press ENTER to search and store all available channels.

PICTURE

1. Picture Mode
   Available options: User, Standard, Dynamic, Mild.

2. Contrast
   The value of Contrast can be adjusted from 0-100.

3. Brightness
   The value of Brightness can be adjusted from 0-100.

4. Color
   The value of Color can be adjusted from 0-100.

5. Tint
   he value of Tint can be adjusted from -50 to 50.
   NOTE: Tint is adjustable only in certain TV system.

6. Sharpness
   The value of Sharpness can be adjusted from 0-100.
   NOTE : If the value of Contrast, Brightness, Color, Tint or Sharpness has been
   changed, the picture mode will turn to User automatically.

7. Color Temp. (Color Temperature)
   Available options: Normal, Warm, Cool.

AUDIO

1. Sound Mode
   Available options: Standard, Music, Movie, User

2. Bass
   The value of Bass can be adjusted from 0-100.

3. Treble
   The value of Treble can be adjusted from 0-100.

4. Balance
   The value of Balance can be adjusted from -50 to 50.
   NOTE: If the value of Bass or Treble has been changed, the sound mode will turn to User automatically.

5. Surround
   This item is used to turn on/off Sound Surround function.

6. AVC (Auto Volume Control) Available options: On, Off.

7. SPDIF Type
   This item is used to select preferred SPDIF audio output type. Available options: Off, RAW, PCM.

8. Audio Language
   This item is used to select preferred audio language.
   NOTE: This item is adjustable only for digital programs.

9. Accessibility
   This item is used to make accessibility for people who are blind or visually impaired.

• Voice Guide Turn on/off voice Guide for some texts on screen.
• Voice Guide: On, Off
• Volume : Weak, Middle, Strong
• Speed: Weak, Middle, Strong
• Pitch: Weak, Middle, Strong
  Video Description Turn on/off Video Description.

TIME

1. Sleep Timer

   • Available options: Off, 5 min, 10 min,
   • 15 min, 30 min, 45 min, 60 min, 90 min,
   • 120 min, 180 min, 240 min.

2. Time Zone

   • Available options: Eastern, Central,
   • Mountain, Pacific, Alaska, Hawaii, Altlantic.

3. Daylight Saving Time
   Available options: On, Off.
   NOTE: This item is adjustable only for digital programs.

4. Clock
   When an available digital program is present, this unit will get Date and Time
   information automatically from current program. And it’s not user adjustable.

SETUP

1. Menu Language
   This item is used to select preferred OSD menu language.

2. Transparency
   This item is used to turn on/off Transparent OSD menu.

3. Zoom Mode
   This item is used to select preferred zoom mode of display screen. Available options: Normal, Wide, Zoom, Cinema.
   NOTE: The available zoom mode may be different for different input source.

4. Noise Reduction
   Available options: Off, Weak, Middle, Strong.

5. Closed Caption CC Mode Available options: CC on Mute, Off, On.
   Basic Selection Available options: CC1, CC2, CC3, CC4, Text1, Text2, Text3, Text4.

Advanced Selection
Available options: Service1, Service2, Service3, Service4, Services, Service6.
Option
Mode
Available options: Default, Custom.

• Font Style
  Available options: Default, Font 0, Font 1, Font 2, Font 3, Font 4, Font 5, Font 6, Font 7.

• Font Size
  Available options: Default, Normal, Large, Small.

• Font Edge Style
  Available options: Default, None, Raised, Depressed, Uniform, Left Shadow, Right Shadow.

• Font Edge Color
  Available options: Default, Black, White, Red, Green, Blue, Yellow, Magenta, Cyan.

• FG Color
  Available options: Default, White, Red, Green, Blue, Yellow, Magenta, Cyan.

• BG Color
  Available options: Default, Black, Red, Green, Blue, Yellow, Magenta, Cyan.

• FG Opacity
  Available options: Default, Solid, Flashing, Translucent, Transparent.

• BG Opacity
  Available options: Default, Solid, Flashing, Translucent, Transparent.

NOTE: Advanced Selection and Option are adjustable only for digital programs.
DLC
This item is used to turn on/off Dynamic Luminance Control.
OverScan (HDMI mode only)
Turn on OverScan if users can not get full screen display in HDMI mode.
Restore Default
This item is used to reset to factory default settings.
CEC
Press the RIGHT navigation button or OK button to enter it.
Note: Connect external HDMI device featured with HDMI CEC function first before
following operations.

• * Press the right arrow button or ENTER button to enter it.

• CEC Control: Turn on/off HDMI CEC.
• Device Auto Power Off: Turn on/off the device auto power off.
• TV Auto Power On : If this function is enabled, the TV will power on automatically after turningon an externally connected CEC device.
• Audio Receiver: Turn on/off the audio receiver.
• Device Lists: Press Enter to display available devices
• Connect: Turn on/off the audio receiver
• Root Menu: Press Enter button into the root menu.

LOCK

• Input the password by pressing number buttons on remote control.
  NOTE: The factory default password is 0000.

Change Password

• Press RIGHT navigation button or ENTER button to enter it.
• Press number buttons to input the new password and input it again to finish password changing.

System Lock
This item is used to turn on/off system lock.
us TV

• Press RIGHT navigation button or ENTER button to enter it.
• Press navigation buttons to move the cursor.
• Press ENTER button to block or unblock it.

MfAA
Available options: N/A, G, PG, PG-13, R, NC-17, X.

Canada
Canada English
Available options: E, C, CS+, G, PG, 14+, 18+.
Canada French
Available options: E, G, 8 ans+, 13 ans+, 16 ans+, 18 ans+.

NOTE: US, Canada, RRT Setting and Reset RRT items are adjustable only when System Lock is On.

RRT Rating
This item is available only when viewing programs which contain related Advance Rating information.

Reset RRT
This item is used to reset RRT Rating.

Hotel Menu

• Press RIGHT navigation button or ENTER button to enter it.
• Hotel Mode: turn on/off Hotel Mode.
• Boot Setting: set Picture Mode, Default Volume, Max Volume, Boot Source. (Boot Channel & Channel Select won’t work if no TV signals.)
• Hotel Lock: turn on/off Tuner Lock, Keypad Lock or Menu Lock.
• Power Save: select desired Power Save time.
• TV to USB: export data to USB device.
• USB to TV: import data from USB device.
• Reset Hotel Setting: reset above hotel setting.

CHANNEL

1. Air/Cable
This item is used to select preferred signal receiving type.

Auto Scan

Press RIGHT or ENTER button to enter it.

Cable System

• This item is used to select preferred cable system. Available options: AUTO, STD, IRC, HRC.
  NOTE: This item is adjustable only when your signal type is set to Cable.

Start to Scan

• Press RIGHT or ENTER button to start auto scanning.
• Press MENU or EXIT button to exit auto channel searching.

Favorite

• Press RIGHT or ENTER button to enter it.
• Press UP or DOWN navigation button to select preferred channel.
• Press ENTER button to label the selected channel as a favorite one or not.

Show/Hide

• Press RIGHT or ENTER button to enter it.
• Press UP or DOWN navigation button to select preferred channel.
• Press ENTER button to show or hide the selected channel.

Channel No.

• Press LEFT or RIGHT navigation button to select preferred channel number.

Channel Label

• Press RIGHT or ENTER button to enter it.
• Press LEFT or RIGHT navigation button to move the cursor.
• Press UP or DOWN navigation button to adjust the value.
  NOTE: If no available channel is present, Favorite, Show/Hide, Channel No., and Channel Label will not be adjustable.
  DTV Signal This item is not user adjustable.

USB

USB OPERATION

• Insert a USB memory device, which contains Photo or Music files, into USB slot.
• Press SOURCE button on the remote control to switch this unit to USB (or Media) mode.
• Press LEFT/RIGHT navigational button to choose between the Photo or Music page.
• Press UP/DOWN navigational button to select and press the OK button to open the file.

Photo Playback

• Select Photo tab on the USB page.

Press UP/DOWN navigation button to select preferred folder/file and press the ENTER button to enter a folder or play selected file.

Durning playback

• Press UP/DOWN navigation button to play previous/next photo.
• Press LEFT/RIGHT navigation button to rotate a photo counterclockwise/ clockwise.
• Press EXIT button to return to Photo menu page.

Music Playback

• Select the MUSIC tab on the USB page.
• Press UP/DOWN navigation button to select preferred folder/file and press the ENTER button to enter a folder or play selected file

Durning Playback

• Press INFO button to display/hide the tool bar.
• Press LEFT/RIGHT navigation button to select preferred option and press ENTER button to confirm it.

Troubleshooting

If you have any problem, review the solutions for each symptom listed below. The following symptoms may have been caused by inappropriate adjustment rather than actual malfunction of the unit. If the trouble persists, contact the Customer Care Center, see back page for contact details.

picture defects  and the reason

Snowy Picture
Snowy picture is usually due to weak signal. Adjust antenna or install an antenna amplifier.

Double Image or Ghosts
Double images are usually caused by reflections from tall buildings. Adjust the direction of the antenna or raise it.

Radio Wave Interference
Wave patterns are moving on the screen, which are usually caused by nearby radio transmitters or shortwave receiving equipment.

High Temperature Electrothermal Interference
Diagonal or herringbone patterns appear on the screen or part of picture is missing. This is probably caused by high temperature electrothermal equipment in a nearby hospital.

FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Support
If you have problems with your device, please consult the instructions in this manual. Please also visit us on the web at www.naxa.com to get up to the minute news, alerts, and documentation for your device. For additional assistance, please contact Naxa Technical support.
NAXA Technical Support 2320 East 49th St. Vernon, CA90058 Tel: (323)-583-8883 http://www.naxa.com/naxa_support/ Made in China

References

• Naxa Support – Naxa Electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>