KINGFORCE M15 Electronic Lock Installation Guide
- June 5, 2024
- KINGFORCE
Table of Contents
KINGFORCE M15 Electronic Lock
COMPONENTS
LIST
Tools Required
Tools Required for Installation on Pre-drilled Doors
Phillips Screwdriver (DO NOT USE POWER DRILL!)
Quick start tip
- We sincerely recommend you scan the QR code below to watch our product installation and programming video on Youtube which will save your valuable time.
- Our customer support team is providing video call guide service now,which will guide you to complete the lock installation and setups in minutes. Feel free to email us at support@kingforceusa.com to schedule your video call
INSTALLATION STEP 1
Prepare the door and check the dimensions
If drilling a new door, use the supplied template and the complete door
drilling instructions
- Measure to confirm that the hole in the door is 2-1/8″ (54 mm).
- Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70 mm).
- Measure to confirm that the hole in the door edge is l’ (25 mm).
- Measure fo confirm the thickness of the door is between 1-3/8″ and 2″/35mm and 50mm).
INSTALLATION STEP 2
Install the latch and strike
- Insert the latch bolt into the door.
- Install strike on the door frame
Install the exterior assembly
Install the interior assembly
- Take off the mounting plate.
- Route cable through the bottom of mounting plate.
- Tighten screws evenly.
- Ensure tight cable connection.
- Tighten screws evenly.
Install the batteries and perform the door handing process
Note: Do not use rechargeable batteries or Non-alkaline batteries.
- Install 4 AA batteries in battery pack.
Perform the door handing process. Press ,the latch bolt extends by itself. If
the latch bolt extends or retracts not smoothly. please check the latch and
re-install the lock.
PROGRAMMING GUIDE
The Tuya APP is available for iOS and Android devices-free of charge. You can set up, operate and control all your Kingforce products with Tuya app.
Download Tuya App
Two methods to download Tuya App.
- Method 1： Scan the following QR code to download Tuta App.
- Method 2：Search Tuya Smart in APP store or Android APP store to download
Connect smart lock
(Attention: the smart lock and the phone can only be allowed one-to-one
connection at the same time. It means that if your phone is connecting with
the smart lock, then the other phone can’t connect the smart lock.)
Advanced setting optional
How to set up a new entrance
- Step 1: Invite your members to family
- Step 2: Control smart lock (Two ways)
- Step 3: Set up a new entrance successfully
How to modify password
How to delete password
How to set delay time
How should I do if I can’t connect to smart lock
Restart the Bluetooth, and try again.
How many passwords can be added
It can be added for ten passwords.
Protection mode
If you enter the wrong code 5times, the keypad will be locked 90 seconds when you press any button, you will hear 3 beeps and 3 red lights.
How to exit protection mode
- wait for 90 seconds and the protection mode will be exited. option
- remove the battery for more than 5 seconds and then reinsert the battery.
Factory default reset
A factory reset will delete all codes associated with the lock.
Keep press holding set button more than 5 seconds until the lock short beeps 5 times and light flash blue 5 times. then the beeps 1 second and light flash green 1 times. the lock has been reset sucessful.
SYSTEM ALERT
| Alert | Reason | Solution |
|---|
button flashes red
3 times with 3 beeps.
| Door jammed while attempting to lock.| Manually re-lock door. If needed, reposition strike.
Incorrect User Code ente red.
|
Re-enter User Code.
button flashes red
3 times with 3 beeps.
|
5 incorrect User Codes entered within one minute.
|
Re-enter User Code after 90 seconds keypad lock out.
LED redlight when press any button.|
Low battery.
|
Replace batteries.
LED redlight when press any button. and can not unlock/lock.|
Super low battery.
LED green light and beeps 1 second after press unlock/lock button.
the lock no respond.
|
Poor quality battery.
The keypad and light indicator no respond.
|
Battery run out.
| Use Micro-Usb supply power to unlock or key to unlock then replace
batteries.
Bad cable connection.| Re-connect the cable.
Customer Support
Quick start tip
- We sincerely recommend you to scan the QR code below to watch our product installation and programming video on Youtube which will save you valuable time.
- Our customer support team is providing video call guide service now,which will guide you to complete the lock installation and setups in minutes. Feel free to email us atsupport@kingforceusa.com to schedule your video call.
Prepare Door And Jamb
- TEMPLATE
- Cut out template printed of this Manual (Figure 1a).
- Fold template and place on door 36″ (915mm) from the ground as marked (Figure 1b).
- MARK THE DOOR FOR DRILLING FIgue 1à Figure lb
- Mark center hole on door edge through guidance on template for 1″ (25mm) latch bolt (Figure 2a)
- Mark center hole on door face through guidance on template for 2-3/8″ (6Omm) or 2-3/4″ (70mm) (Igure 2b) backset.
- DRILL AND CHISEL DOOR
- Drill 2-1/8 (54mm) hole through door panel as marked for lock set (Figure 3a).
- Drill 1″ (25mm) hole in center of door edge for Deadbolt Latch Assembly (Figure 3b).
- Insert Deadbolt Latch Assembly in hole keeping it parallel to Tace of dor.
- Mark oudine and remove latchn igure 2a igure 40 FIgre sa 30 figure
- Chisel 5/32(4mm) deep or until latch face is flush with door edge (Figure 3d). Figure 3c Figure 3d NOTE: For Drive in Latch, drill hole size indicated on template and press until it is flush with door edge.
- MARK AND DRILL D0OR JAMB
- Mark center hole on edge of jamb even with the center of the Latch Bolt on door edge. (Figure 4a).
- Drill 1″ (25mm) hole 1-3/16″ (30mm) deep in door jamb on center mark (Figure 4b).
- Outine outside edges of Strike Plate (Figure 4c).
- Chisel 5/32′(4mm) deep for Strike Plate or untilit is flushed (Figure 4d).
- Install Strike Plate using two 3/4″ (19mm)screws provided (Fiqure 4e).
Tools Required
Tools Required for Installation on undrilled Doors
Phillips Screwdriver (DO NOT USE POWER DRILL!)
TEMPLATES
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>