eufy E8213 Security Video Doorbell Dual Camera User Guide

eufy E8213 Security Video Doorbell Dual Camera

WHAT’S INCLUDED

For Video Doorbell Installation

For HomeBase 2 Installation

Note : Power plug may vary in different regions.

PRODUCT OVERVIEW

Video Doorbell

Front View:

1. Motion Sensor
2. Microphone
3. Primary Camera Lens
4. Ambient Light Sensor
5. LED Ring / Doorbell Button
6. Secondary Camera Lens
7. Speaker

Rear View:

1. Detaching Mechanism
2. Micro USB Charging Port
3. SYNC/RESET Button
4. Power Terminals for Existing Doorbell Wires (Optional)

beep.
Power off the doorbell| Quick-press the SYNC button 5 times in 3 seconds.
Reset the doorbell| Press and hold the SYNC button for 10 seconds.

HomeBase 2

1. Status LED
2. Speaker
3. Power Port
4. USB Port
5. Ethernet Port
6. SYNC/ALARM OFF Button
7. Reset Button

HOW THE SYSTEM WORKS

The video doorbell system includes 2 parts. One is the video doorbell at your door. The other is the HomeBase in your house. The video doorbell detects motion at your porch and allows you to answer the door anytime and anywhere. The HomeBase stores video clips on its built-in  Doorbell Chime

Connect HomeBase 2 to the Internet

1. Power on the HomeBase 2, then use the ethernet cable provided to connect the HomeBase 2 to your home router.
2. The LED indicator turns blue (this may take up to 1min) when HomeBase 2 is ready for setup.

Download the App and Set up the System
Download the eufy Security app from the App Store (iOS devices) or Google Play (Android devices).

Sign up for a eufy Security account, then follow the onscreen instructions to complete the setup.

DETERMINING THE POWER OPTION

Option 1 – Battery Powered

1. If you don’t have existing doorbell wiring at the front door, use the built-in battery. You are free to determine the doorbell position and the mounting is easy and quick.
2. When the doorbell battery level is low, you need to detach and charge it.
3. If you choose this option, please jump to STEP 4 FINDING A MOUNTING SPOT.

Note: The battery life varies depending on usage. In most common cases, a doorbell may have up to 10 events per day and each recording lasts 20 seconds on average. Under this scenario, the doorbell battery life can last up to 6 months.

Option 2 – Doorbell Wire Powered

1. If you have existing and working doorbell wiring at the front door, the doorbell will be powered by the wires constantly. So you don’t need to detach and charge it after installation.
2. Since the doorbell is connected to the wires, the mounting position is limited.
3. If you choose this option, please jump to APPENDIX 3 POWERING THE DOORBELL WITH EXISTING DOORBELL WIRES.

Find a Mounting Spot
Take the video doorbell to your front door and check the live view on the app

Consider the following factors:

1. Check if you can reuse the existing holes and anchors on the wall or door frame.
2. If you want to place the doorbell close to a side wall, make sure the wall  night vision will become blurry.
3. mounting height is 48″ / 1.2 m from the ground.
4. To adjust the angel, use the 15° mounting wedge as a supplementary mounting bracket.

Place the screw hole positioning card against the wall to mark the position.

Mount the Doorbell on a Wooden Surface
If you’re mounting the doorbell on a wooden surface, you don’t need to pre- drill pilot holes. Use the provided screws to secure the mounting bracket on the wall, the screw hole positioning card indicates the position of the screw holes. What you need: Screwdriver, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Packs

Mount the Doorbell on Surfaces Made Out of Hard Materials

1. If you’re mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco, drill 2 holes through the screw hold positioning card with a 15/64”(6mm) drill bit.
2. Insert the provided anchors, and then use the provided long screws to secure the mounting bracket on the wall.

What you need: Power Drill, 15/64”(6 mm) Drill Bit, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Packs

Mount the Doorbell
Align the doorbell on the bottom, and then move it into place on top. Press the doorbell down until it clicks.

You’re all set! If you want to detach the doorbell or recharge it, please refer to the following sections.

Detach the Doorbell

1. Use the doorbell detaching pin provided if you wish to detach the doorbell from the mounting bracket.
2. Press into the pinhole on top of the doorbell, and then lift the top for removal.

What you need: Doorbell Detaching Pin

Recharge the Doorbell

Verify whether the doorbell wires are working

1. Ring the existing doorbell to check if it is working. If the doorbell doesn’t ring, your doorbell wires may be defective. Power the doorbell on its own
2. Shut off power at the breaker. Turn the lights on / off in your home to make sure the electricity in your house is properly shut off.

Always be careful when handling wires. If you’re not comfortable

Detach the Existing Doorbell Button
If you already have existing doorbell wiring:

1. Remove the existing doorbell button with a Phillips-head screwdriver (not provided).
2. Pull the two wires out carefully when removing the existing doorbell. Straighten the wire ends if necessary.

What you need: Philips-Head Screwdriver

Find a Mounting Spot

1. When determining the mounting position of the doorbell, consider these factors:
2. Check if you can reuse the existing holes and anchors on the wall or door frame.
3. mounting height is 48″ / 1.2 m from the ground.
4. To adjust the angel, use the 15° mounting wedge as a supplementary mounting bracket.
5. Place the screw hole positioning card against the wall to mark the position.

Mount the Bracket
If you’re mounting the doorbell on a wooden surface, you don’t need to pre- drill pilot holes. Use the provided screws to secure the mounting bracket on the wall. The screw hole positioning card indicates the position of the screw holes. What you need: Power Drill, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Packs

If you’re mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco:

1. Drill 2 holes through the screw hole positioning card with 15/64”(6mm) drill bit.
2. Insert the provided anchors, and then use the provided long screws to secure the mounting bracket on the wall.

What you need: Power Drill, 15/64”(6mm) Drill Bit, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Packs.

Connect the Doorbell Wires to the Doorbell
Connect the wires to the terminals at the back of the doorbell, then tighten the terminal screws. Wire can connect to any terminal. What you need: Wires and Wire Nuts (Optional), Video Doorbell, Philips-head Screwdriver

Note:

• To prevent short-circuiting, make sure the wires are not touching each other after connecting them to the terminals.
• If the wires are too short, use the extension wires and wire nuts provided to make them longer. Use electrical wiring tape instead if there is no more space on the wall for wire nuts.

Mount the Doorbell on the Bracket
Align the doorbell on the bottom, and then move it into place on top. Press the doorbell down until it clicks.

Restore Power
Switch the master circuit breaker back to ON.

You’re all set! If you want to detach the doorbell or recharge it, please refer to the corresponding sections.

NOTICE

This product complies with the radio interference requirements of the European Community Declaration of Conformity Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.For the declaration of conformity, visit the Web site: https://uk.eufylife.com/.
The adapter shall be installed near the equipment and shall be easily accessible. Do not use the Device in the environment at too high or too low temperature, never expose the Device to strong sunshine or too wet environment. The suitable temperature for the product and accessories is -20°C to 45°C. When charging, please place the device in an environment that has a normal room temperature and good ventilation. It is recommended to charge the device in an environment with a temperature that ranges from 5°C~25°C. Please ensure to use only the adapter offered by the manufacturer. Using an unauthorized charger may cause danger and violate the guaranteed article. This adapter is for indoor use only. The adapter type is KA2401A-1202000DE/, output voltage/current is 12Vdc/2A. The plug is considered as a disconnect device of the adapter. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement product that maintains a 20cm distance between the device and the human body. The Device T8213 Wifi Operating Frequency Range:2412~2472 MHz(2.4G); Range:23-24 GHz(24GHz); for 24Ghz) The Device T8010X Wifi Operating Frequency Range:2412~2472 MHz(2.4G); Range:866-866.8 MHz(Sub-1G); Power:5.492dbm(EIRP for Sub-1G) Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807 Munich, Germany

Declaration of Conformity
Hereby, Anker Innovations Limited declares that this product is in compliance with Radio Equipment Regulations 2017. The full text of the UK declaration of conformity is available at the following internet address: https://uk.eufylife.com

References

• fios.se
• Porkbun Marketplace: The domain mur.la is for sale.
• eufy | Built with Care | Up to 53% Off | eufy UK
• VAST Fetish Gear
• eufy | Built with Care | Up to 53% Off | eufy UK
• eufy | Built with Care | Up to 53% Off | eufy UK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>