eta Puretee Air Purifier Instructions
- June 5, 2024
- ETA
Table of Contents
Air Purifier • INSTRUCTIONS FOR USE
PURETEE
Air Purifier
eta 0569
INSTRUCTIONS FOR USE
Dear customer, thank you for purchasing our product. Please read the operating
instructions carefully before putting the appliance into operation and keep
these instructions including the warranty, the receipt, and, if possible, the
box with the internal packing.
SAFETY WARNING
Special warnings and information
– This appliance includes an ultraviolet radiator UV-C. Improper use of or
damage to the appliance may result in the leak of dangerous UV-C radiation.
Even a small concentration of radiation may cause damage to the eyes and skin.
– MERCURY WARNING – As UV lamp contains mercury, do not throw it in
regular waste! The UV lamp is a hazardous waste that must be liquidated in
accordance with the applicable regulations of national legislation.
– Never look into the UV lamp or put your face near the front or back part
during operation
– To avoid overexposing to ultraviolet light, people and animals must be at
least 30 cm from the device. A short exposition to the light in close
proximity is safe.
– This appliance complies with the limits of the maximum admissible ozone
concentration (0.05 ppmv/24h).
– Do not use the appliance in bathrooms in zones 0, 1, and 2 (Fig. 3)!
– Do not place the appliance under the electrical socket. For safety reasons,
leave the minimum distance of 0,5 m between the appliance and any obstacle on
any side (furniture, walls, etc.).
– Do not immerse the cleaner in water or other liquids (not even partially)
and must not be used in close proximity of bathtubs, showers, basins or other
containers with water, including pools! It must not be used in a damp or wet
environment! If the cleaner should still fall in the water, do not take it
out! Unplug the plug of the adaptor from the socket first and only then take
out the device. In such cases, the device shall be taken to an expert service
center to be checked for safety and correct functionality.
– Do not use the device in places (e.g. workshops, manufacturing plants,
garages, or other technical rooms) where there are hot, flammable, and
explosive materials (e.g. ashes, burning cigarette butts, gasoline, diluents,
dissolvent and aerosol fumes) or lubricants (e.g. fats, oils), chemicals,
caustic agents (e.g. acids, dissolvent, paints). Sucking in the flammable and
explosive gases, the filters or the cleaner can be damaged or can cause fire,
explosion or electrical shock. The air is ionized by microscopic el. sparking
(so-called corona discharge) which can set flammable substances on fire. – Do
not use textile or other materials (e.g. drapes, curtains, blankets) to cover
this device. If the air inlets and outlets are covered, it will cause abnormal
operation and may lead to fire or other accidents. Do not put the cleaner on
soft surfaces (e.g. bed, towels, kitchen towels, carpets) while it is on.
– This appliance is not intended for outdoor use.
– Always place the device on a flat, dry surface and use it only in a vertical
position. Do not move the device during operation.
– To ensure flawless circulation of all the air in the room, do not use the
device in niches, narrow hallways, or behind furniture.
– Do not place the device near gas appliances, fireplaces, and open flames.
Not even near fireplaces that are not currently in use. Dust and soot may
circulate through the cleaner and consequently settle in the device and the
room. We do not recommend placing the device anywhere near burning candles,
paraffin lamps, etc.
– Place the device at a good distance (at least 1 meter) from a computer,
television or radio. You can thus avoid interference and distortion when
operating these devices. – Do not place the appliance directly under a smoke
detector, as its sensibility might be decreased.
– Only use the appliance in the working position at places with no risk of
overturning and in a sufficient distance from other objects (such as curtains,
drapes, etc.), heat sources (e.g. fireplace, heater, stove, cooker, radiators,
hot air ovens, grills) and wet surfaces (e. g. sinks, washbasins).
General warnings and information
– Consider the instructions for use as a part of the appliance and pass them
on to any other user of the appliance.
– Check whether the data on the type label corresponds with the voltage in
your socket (this product is designed to operate within a range of 100-240
volts). The adaptor plug may only be connected to the electrical socket
complying with the applicable standards.
– This appliance may only be used by children aged 8 years or older, and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning the use of the appliance in a safe way understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision. Children
younger than 8 years must be kept out of reach of the appliance and its power
cord. – To power the appliance, only use the adapter included.
– Before exchanging any accessories or accessible parts that are moving during
use, before assembly and disassembly, before cleaning and maintenance, when
carrying, when you leave it unattended or after finishing the work, switch off
the appliance and disconnect it from the mains by unplugging the adaptor plug
from the electrical socket!
– For additional protection, install current protection (RCD) with the nominal
release current not exceeding 30mA. Ask a revision technician or an
electrician for advice.
– If the adaptor of the adaptor is corrupted, it has to be replaced by the
manufacturer, its service technician or a similarly qualified person so as to
prevent dangerous situations.
– Never use the appliance if its adaptor or plug is damaged, if it does not
work properly if it fell down and was damaged. In this case, take the
appliance to a special service to check its safety and proper function. –
ATTENTION: Do not use this heater in series with an external timer, remote
controller or any other device that switches on the appliance automatically,
since a fire risk exists when the heater is accidentally covered or displaced
at the moment it switches on.
– Do not handle the appliance with wet hands.
– Do not plug the power cord in the electrical socket and do not unplug it
with wet hands or by pulling the power cord!
– High voltage inside the device may cause electrical shock. – Do not leave
the device exposed to weather (e.g. rain, freeze, direct sunlight, and
temperatures exceeding 60 °C).
– Never let the flow of air blow on you (or animals) for an extended period of
time. It may cause health problems.
– Check the correct position of filters. Otherwise, the device can not be put
to operation.
– Pay attention not to put fingers, parts of the body, loose clothes, jewelry,
and other objects into the air openings when operating.
– Apart from regular basic maintenance and cleaning (potential replacements)
of filters should any other maintenance and repair be done by a professional
service center personnel. Not following this requirement may lead to warranty
termination.
– Do not use the purifier as a substitution for proper ventilation, for
example as a source of fresh air or as a substitution for forced ventilation
(kitchen, extraordinarily dusty environment, etc.).
– Never immerse the network adapter or the purifier unit (not even part of it)
in water and protect them against wet or damp conditions!
– Do not plug the appliance during storms.
– Never use the appliance without inserted filter, UV lamp, and without
properly fixed UV lamp cover. Do not use it when filter, UV lamp or other
components fixing/protecting UV lamp are damaged.
– Do not let foreign objects to get into the device. High voltage inside the
device may cause electrical shock. Do not let children touch the device.
– The air cleaner is an electrical device. If it is used in the presence of
children, supervision by a responsible adult person is necessary.
– Only use original components designed for this type.
– To avoid stumbling, lead the cable outside the regular walking areas.
– Check the condition of the power cord of the appliance regularly.
– Never put the power cord on hot surfaces and never let it hang over the
table edge or worktop edge. If the cord is caught or pulled, e.g. by children,
the appliance may overturn and fall down, causing a serious injury!
– If you need to use an extension cord for justified reasons, it must be
undamaged and comply with the applicable standards.
– Only use this appliance for the purpose it was designed for, as specified in
this manual. Never use the appliance for any other purpose.
– WARNING: There is a risk of injury when the appliance is not used correctly
(not in accordance with the manual).
– The manufacturer assumes no responsibility for any damage caused by improper
handling of the appliance and its accessories (e.g. electric shock, fire), and
the appliance guarantee will become void if any of the aforementioned safety
instructions are not observed.
II. DESCRIPTION OF THE APPLIANCE (Fig. 1,2)
A – Main unit (Fig. 2)
A1 – socket for the mains cable
A2 – the mains adapter
A3 – Air outlet
A4 – Air inlet| A5 – HEPA filter 3 in 1
A6 – Filter cover
A7 – UV lamp
A8 – UV lamp cover
---|---
B – Control panel (Fig. 1)
B1 – Switch on/off button ( )
B2 – Fan speed button ( )
B3 – Speed level indicators
B4 – night light button ( )| B5 – Filter replacement indicator
B6 – UV disinfection function button
B7 – Timer button
---|---
III. INSTRUCTIONS FOR USE
Before first use, remove any packaging and protective material (including any
protective film) from the appliance and accessories.
CONTROLS
After switching the purifier into standby mode, plug the adaptor cable in an
electrical socket. An acoustic signal will sound, and all indicator lights
will turn on for a moment. hen the B1 the button remains lit.
Switch on/off button B1 – Press the button to switch on the purifier in
the basic filtration mode (speed Low). The set functions may be canceled by
repeated pressing of this button, and the purifier may be switched back to the
standby mode.
Fan speed button B2 – You can switch the fan speed by repeatedly pressing
this button as follows: High – Mid – Low – SLEEP. The respective indicator
light B3 will indicate the respective speed setting.
The B4 light button – when the appliance is on, the nightlight in the
lower part of the purifier is activated. Press the button again to turn off
the light.
SLEEP – Pressing the B2 button to SLEEP activates the silent mode
recommended for night operation. The cleaner will operate at the lowest speed
level, and without any light signals. The function may be disabled by pressing
the B1/B2 button.
UV function button B6 – Press this button to activate UV sterilization of
the air flowing through. The function activity is indicated by the blue
backlight of the UV function ionization button. Press the button to switch off
the function.
Timer button B7 – Press this button to activate the sleep function to
switch off the device after 1, 2, 4, or 8 hours. After the set period expires,
the purifier shall automatically switch to standby mode. You may set the
following values by pressing the button repeatedly: 1 hour – 2 hours – 4 hours
– 8 hours – function switching off …
FILTER REPLACEMENT
To replace HEPA filter A5, proceed according to Fig. 2. If the filter
replacement indicator light B5 is flashing, it indicates the end of the
filter’s service life. The B5 indicator light will flash after about 1500
hours of operation – then the filter must be replaced (unless it has been
replaced earlier due to impurities and higher dustiness level). To restart the
signalization function after the filter replacement), press the B4 and B6
buttons for 3 seconds. The signalization function must be restarted in the
same manner also when you replace the filter before the signalization light is
activated.
UV LAMP A7 REPLACEMENT
The UV lamp is designed for about 15,000 operating hours, this equals to about
20 months of continuous 24/7 operation. Based on the frequency of use, for
most users, it means they will never need to replace the lamp. However, if you
reach the end of its lifecycle, or if you want to dispose of the appliance,
please detach it by unscrewing 2 screws on the sides that hold the plastic
cover A8, where the UV lamp is placed. There are several jumper cables in the
UV lamp cover and also in the purifier main unit, which are connected with
plastic joints in the middle – it is necessary to detach the cover with the
cable here and attach a new lamp. When placing the cover with the lamp back
inside the purifier, proceed carefully in order not to squash the cable –
place the cable carefully in the hole in the cover/purifier and then screw the
cover tightly. If you do not want to replace it yourself for whatever reason,
ask a qualified person to do it for you.
MAINTENANCE
Maintenance of the purifier includes cleaning the power unit body and
replacing of the filter.
Power unit – Only clean the power unit body with a slightly damped cloth
with a non-aggressive cleaning agent added. Do not allow water to get inside!
Let the purifier thoroughly dry out before using it again.
HEPA filter A5 – To guarantee proper function and air purification
quality, the HEPA filter must be replaced in regular intervals. Never wash the
filter to avoid reducing the filtration capacity of the filter; only knock it
out, vacuum or blow it with compressed air – however, this will not fully
restore the filtration capacity of the filter. The recommended replacement
interval is after 6 months of regular use. New filter order code: ETA056900070
UV lamp A7
The UV lamp is designed for about 20 months of non-stop operation. After this
period, the lamp will start losing its disinfection qualities, and we
recommend replacing it for effective air purification. The lamp replacement
interval depends on the frequency of your use of UV disinfection. New UV lamp
order code: ETA056900060
ENVIRONMENT
Printed signs of materials used for manufacture, packing, components, and accessories, as well as their recycling, are on all the pieces if their dimensions enable it. The symbols on the product or in the accompanying documentation mean that the used electric or electronic products must not be disposed of together with municipal wastes. Please, hand them over to the collection points designed for their correct disposal, where they will be accepted free of charge. By correct disposal of this product, you can help to preserve valuable natural resources and help to prevent possible negative impacts to the environment and to human health, which could be the results of incorrect waste disposal. For further details ask the municipal authorities or the nearest collecting point. Penalties can be charged for incorrect disposal of such wastes, according to national regulations. If the appliance is to be put out of operation definitely, we recommend cutting off the feeder cable, to disable its use.
UV Lamp Disposal
If the UV lamp breaks, turn off the air purifier. DO NOT operate it with a
broken lamp. DO NOT use a vacuum to clean up the breakage. Sweep debris into a
plastic bag and dispose of it properly.
Contact your local waste management authority for instructions regarding
recycling and the proper disposal of old lamp(s). DO NOT place your used
lamp(s) in the trash. Disposal of any item containing mercury must be in
accordance with any hazardous waste disposal or recycling laws and regulations
of your state.
Expert service must do the large maintenance or to intervene in inside parts of the appliance! Non-observance of the instructions of the manufacturer cancels the right for guarantee repair!
TECHNICAL DATA
Voltage (V)
Absorbed power (W)
Weight (kg) approximately
Size of the product (mm)
The concentration of negative ions
Input in off mode is| shown on the type label of the appliance
shown on the type label of the appliance
2
215 x 215 x 460
3 mil./cm
3
< 0,5 W
---|---
The manufacturer reserves the right to change the technical specifications and accessories for the respective models.
Charging adapter|
---|---
Manufacturer’s name or trademark, business registration number and address|
ETA
Model identifier| IVP1200-1500G
Input voltage| 100-240 V (AC)
Input frequency| 50/60 Hz
Output voltage| 12 V (DC)
Output current| 1.5 A
Output power| 18 W
Average efficiency in active mode| 87%
Low load efficiency (10%)| 83,7 `)/0
Power consumption without load| 0,5 W
Appliance protection class| II.
– Please read the instructions manual
– Removable power supply unit
HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS. TO AVOID THE DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES, OR PLAYPENS. THIS BAG IS NOT A TOY.
© DATE 25/9/2020
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>