COSTWAY HW67582 Electric 55 in. x 28 in. Standing Desk Sit Stand User Manual
- June 5, 2024
- COSTWAY
Table of Contents
USER’S MANUAL
Before You Start
Retain instructions for future reference.
Separate and count all parts and hardware.
Read through each step carefully and follow the proper order.
We recommend that, where possible, all items are assembled near to the area in
which they will be placed in use, to avoid moving the product unnecessarily
once assembled.
Always place the product on a flat, steady, and stable surface.
Keep all small parts and packaging materials for this product away from babies
and children as they potentially pose a serious choking hazard.
IMPORTANT SAFEGUARDS
Read these instructions carefully and retain them for future use.
When using the product, basic safety precautions should always be followed to
reduce the risk of injury including the following:
- Unpack all hardware bags and components to ensure you have all the parts.
- Use the tools included to assemble the desk, don’t use the incorrect tools to assemble.
- Do not climb, stand or sit on the desk.
- Do not place objects on the desk when moving.
- Check to ensure that all bolts, screws, and brackets are tightened on a regular basis.
- Do not place the table in a humid environment.
- Do not place heavy objects on the table when storing.
- There is a potential risk of personal injury not following the instructions when in use.
Parts List
Assembly steps
Step 1:
1.1 Connect the 1 board and the 2 boards with wooden pins. Then
connect 3 and 4 to the 1 and 2 tables with wooden pins.
1.2 Fasten connecting blocks H 1, and H2, with J M6 screws as shown in the
figure. M6 screws use the supplied spanner N1.
1.3 The hand controller is fastened to the table with L self-tapping
screws. Self-tapping screws use the supplied screwdriver N3.
1.4 After installing the G2 power supply holder, set it aside.
Step 2:
Assemble the 2 sets of beam components as shown in the figure before use;
Note:
- Pay attention to the card slot direction.
- The Jimmy screws at the bottom of D1 and D3 cannot be tightened.
Step 3
Fixing A lifting column and B lift column to the table leg with M
M1O screws
using the supplied spanner N 2
Step 4:
4.1 Assembling frame tightened with J M6 screws using the supplied spanner
N1.
4.2 Then install the two side brackets with J M6 screws using the supplied
spanner N1.
Step 5:
5.1 Lay the table board flat and put the table shelf on it.
5.2 Attach two J M6 screws on the middle crossbar, but do not tighten the
screws first. M6 screws use the supplied spanner N 1.
5.3 Stretch the table frame to both sides. Align the screw holes and lock them
with J M6 screws. Then tighten the two middle screws. M6 screws use the
supplied spanner N 1
5.4 Fasten the socket set screws on the middle beam.
Step 6:
6.1 As shown in Figure 1, insert the hexagonal bar into table leg B until the
buckle is not visible.
6.2 Assemble the other end of the connecting rod to the table leg A and screw
on the handle. The handle does not need to be tightened.
Note: As shown in Figure 2 below, it needs to be aligned with the card slot.
6.3 Pull the connecting rod with the handle to the bottom end of the table leg
A in the direction of the arrow as follows.
6.4 Tighten the handle and install the K M4 screws. For M4 screws use the
supplied screwdriver N 3.
6.5 Connect the I3 power cord and motor of the I2 power supply and
I1 handest as shown in the figure.
Operational instructions
-
Lift Column
Press the button or button to control the lift column up or down Press the button to control the up of the lifting column, you can see the height (displayed number) on the screen; press the button to control the down of the lifting column, you can see the height (displayed number) on the screen. -
Set memory height
Press the ( 1234 ) button for 2 seconds, and set the current height to the memory height. When flashing display “Hl”‘H4” for 2 seconds, and then display the real-time height after 2 seconds. -
Recall memory height
Press the number button ( 1234 ) to recall its corresponding height, lift column will automatically run to the right position. -
Stroke reset
“Ella. E20” alarm state or running to the lowest height position, press the button for 5 seconds, after the display ( Reset) is released, the lifting column starts to run down to the bottom of the frame and rebound to a certain height, the reset is completed to display the lowest height.
Protection and alarm
5.1) Block Protection: Display “E02”. During the movement, a vibrating,
colliding, or tilting desktop will sound an alarm and stop the movement
immediately. After the automatic release, it will move in the reverse
direction to set the distance, you can press any key to stop and release
during the reverse operation. Check and make sure that the desktop will not
vibrate significantly, hit obstacles, or re-tilt during operation.
5.2) Overheating protection: Display “Hot.” C continuous operating may
initiate this protection and should be recharged or waited for at least 18
minutes before use.
5.3) Motor abnormal protection: Display “El 0.” Should be powered off, recheck
and ensure that the connection of the motor to the controller is reliable, and
then reconnect.
5.4) Overload protection: Display “E20.” This alarm should be removed from the
desktop when it’s operating up; if this alarm occurs when it’s operating down,
cut off the power and the heavy objects should be removed, and the power
should be re-charged. ）
5.5 Under-voltage protection: Display “E31.” Should be powered off, recheck
and make sure that the connection between the power supply and the handset is
reliable, then connect the power.
5.6) 0 over-voltage protection: Display “E32.” Should be powered off, recheck
and make sure that the connection between the power supply and the handset is
reliable, then connect the power.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>