steinel XSolar L-S 671006 Solar Spotlight (+ Motion Detector) 1.2 W Cool white White Instructions

steinel XSolar L-S 671006 Solar Spotlight (+ Motion Detector) 1.2 W Cool

white White

About this document

Please read it carefully and keep it in a safe place.

• Under copyright. Reproduction either in whole or in part only with our consent.
• Subject to change in the interest of technical progress.

Symbols

Hazard warning!
Reference to other information in the document.

General safety precautions

• Hazard from vapors or electrolyte fluid! Vapors or electrolyte fluid may escape if the rechargeable battery is damaged or used improperly. Coming into contact with them may result in severe injury (e.g. loss of sight, acid burns).
• Never open the rechargeable battery enclosure or the rechargeable battery itself.
• Do not allow vapors or electrolyte fluid to come into contact with your eyes. In the event of contact with eyes:
  • Do not rub your eyes.
  • Immediately rinse eyes with plenty of clean water (such as tap water).
  • Seek medical advice.
• Do not touch any electrolyte fluid that has escaped.
• Immediately move the product away from naked flamed or sources of heat.
• Immediately remove contaminated clothing.

Hazard from LED light!

Looking directly into the LED light when it is ON could damage your retina.

• Never look into the LED light at a short range or for any prolonged period (> 5 minutes).
  • The light must not be installed in explosive atmospheres.
  • For trouble-free operation, choose an installation site that is not exposed to vibration or shock.
  • Protect the solar panel from mechanical strain (e.g, tree branches).
  • The product must not be modified or altered in any way.

Finishes

• solar L-S white (EAN 4007841671006)
• XSolar L-S silver (EAN 4007841671013)
• Package contents (Ill. 3.1)
• Product dimensions (Ill. 3.2)
• Product components (Ill. 3.3)
• A Solar panel
• B Motion detector
• C LEDs
• D LED panel
• E Micro USB charging socket
• F Compass
• G Programme selector switch
• H Seal
• I Cover, solar-panel holder
• J Cover, LED-panel holder
• K Electronics enclosure
• L Wall mount
• M Extension cable

Setting range for solar panel / LED panel (Ill. 3.4)

Technical specifications for SensorLight

• Output: 6 LED, 1.2 W max.
• Infrared system
• Angle of coverage: 140°
• Detection reach: 8.0 m max. (installed at a height of 1.8 m)
• Area illuminated: 30 m2
• Light-level setting: 2 lux
• Time setting: software-controlled, 10-30 sec.
• Basic light level: 3 %
• Luminous flux: 150 lumens / 124 Lm/w max.
• Colour temperature: 3,000 kelvin
• Solar-panel turning angle: +180°/-150°
• Solar-panel tilt: 55°
• LED-panel turning angle: +/- 60°
• LED-panel tilt: 55°
• Protection class: III
• IP rating: IP 44
• Temperature range: -20 °C to +40 °C
• Dimensions (WxHxD): 189 x 298 186.5 mm

Technical specifications for rechargeable battery

• Nanophosphate® high-power lithium-ion rechargeable battery, cadmium-free LiFePO4.
• Can be recharged at any time without shortening battery lifespan.
• Automatic recharging by a solar panel.
• Can be recharged using a charging adapter at a micro USB socket (5 V).
• Can be replaced by the manufacturer or qualified electricians.
• Rechargeable battery capacity: 2500 mAh
• Max. lighting duration: 60 days at 20 switching operations a night.
• Micro USB charging socket: 5 V, 1 A max., can be used in all three programs.

Recharging time depends on the site of installation (direct sunlight). Expect charging to take many times longer in winter or on rainy days.

Accessories

• Replacement 6 m extension cable for XSolar
• EAN/UPC code 4007841006518

Installation

• Check all components for damage.
• Do not use the product if the solar panel or LED panel is damaged.

Operating reliability will be limited if the product is used in adverse conditions (e.g. installed in shade or behind glass, the solar panel not facing the right direction)

• Choose an appropriate site with plenty of sunlight for installing the solar panel (facing south).

• Avoid shade from porches, overhanging roofs, or trees.

• Pay attention to detection reach (Ill. 4.1).

• Remove wall mount (Ill. 4.2).

• Drill holes and fit rawl plugs (Ill. 4.3).

• Screw-fasten wall mount to the wall (Ill. 4.3).

• Make settings (Ill. 4.4).
  ➔ “6. Operation”

• Screw SensorLight to wall mount (Ill. 4.5).

• Aim LED panel with a motion detector in the right direction (Ill. 3.4).

• Aim for solar panels to get the strongest sunlight for the longest time possible (Ill. 3.4).

• Check compass (for south-facing position) (Ill. 3.4).

Optional

Install LED and solar panel separately
To optimize conditions at the point of use, the solar panel and LED panel can be mounted separately (Ill. 5.1).

• LED panel: light where it’s needed.
• Solar panel: exposed to a high level of direct sunlight.

Risk of damage to property
Pulling on the cable can cause irreparable damage to the product.

• Route the cable out of children’s reach.
• Remove wall mount (Ill. 5.2).
• Separate solar panel from LED panel (Ill. 5.3).
• Drill holes and fit rawl plugs (Ill. 5.4).
• Route extension cable behind wall mount (Ill. 5.4).
• Screw-fasten wall mount to the wall (Ill. 5.4).
• Connect the extension cable to solar panel (Ill. 5.5).
• Fit solar panel holder to the solar panel (Ill. 5.5).
• Screw solar panel to wall mount (Ill. 5.6).
• Pull extension cable downwards (Ill. 5.6).
• Drill holes and fit rawl plugs (Ill. 5.7).
• Route extension cable behind wall mount (Ill. 5.7).
• Screw-fasten wall mount to the wall (Ill. 5.7).
• Connect the extension cable to the LED panel (Ill. 5.8).
• Fit LED-panel holder cover to LED panel (Ill. 5.9).
• Make settings (Ill. 5.10).➔ “6. Operation”
• Screw LED panel to wall mount (Ill. 5.11).
• Pull extension cable downwards (Ill. 5.11).
• Aim LED panel with a motion detector in the right direction (Ill. 3.4).
• Aim for solar panels to get the strongest sunlight for the longest time possible (Ill. 3.4).
• Check compass (for south-facing position) (Ill. 3.4).

Operation

Before using it for the first time

• Activate the light by setting the program selector switch to P2.
  The light stays in test mode for one minute before it starts to work in program P2.

Test mode
During the test sequence, the light works in daytime mode.
On detecting movement, the light switches ON for 1 minute with a stay-ON time of 10 sec. irrespectively of light-level setting. The program is automatically activated after this time elapses.
The red LED stays ON all the time in test mode.

Malfunctions

Red LED flashing in motion detector

• The battery capacity is too low.

  • Charge the battery with a micro USB charging adapter (not included).

• The light does not switch ON

  • The battery capacity is too low.
  • Charge the battery with a micro USB charging adapter (not included).
  • Open or short circuit.

• check connections.

  • Program selector switch set to P0.

• Set program selector switch to P1 or P2.

  • Detection zone is not correctly adjusted.

• Check detection zone.
  The light does not switch OFF

• Continued movement within the detection zone.

• Check detection zone.

  • Light switches ON when it should not

Battery not charging

• Solar panel dirty.
  • Clean solar panel with a soft cloth and mild detergent.
  • Solar panels are not installed in the best place.
• Check site of installation (as much direct sunlight as possible).

Cleaning and Maintenance

The product requires no maintenance.
Regularly checking the product for damage can prolong its lifespan.
Removing dirt can help to make the product work longer.

Risk of damage to property
Using the wrong detergent can damage the light.

• Make sure detergent does not harm the surface.
• Clean light with a soft cloth and mild detergent.

If the solar panel is dirty or the weather has left deposits on it:

• Clean solar panel with a soft cloth and mild detergent.

Disposal

Electrical and electronic equipment, accessories and packaging must be recycled in an environmentally compatible manner. Do not dispose of electrical and electronic equipment as domestic waste.

EU countries only:
Under the current European Directive on Waste Electrical and Electronic Equipment and its implementation
in national law, electrical and electronic equipment no longer suitable for use must be collected separately and recycled in an environmentally compatible manner.
Do not throw devices, rechargeable batteries/batteries into household waste, fire or water at the end of their useful life.
Rechargeable batteries/batteries should be collected, recycled or disposed of in an environmentally friendly manner.

Manufacturer’s Warranty

STEINEL product:

• Manufactured with the utmost care.
• Tested for proper operation and safety in accordance with applicable regulations.
• With final inspection.

STEINEL warranty:

• Warranty on perfect condition and proper working order.
• 36 months starting on the day the product was sold to the consumer.
• Covers the removal of defects resulting from material flaws or manufacturing faults.
• The warranty will be met by repair or replacement of defective parts at our own discretion.
• The warranty does not cover damage to wearing parts.
• This warranty does not cover damage and defects resulting from improper treatment or maintenance.
• Further consequential damage to other objects is excluded from the warranty.
• Claims under the warranty will only be accepted if the product is returned fully assembled with a brief description of the fault, a receipt, or an invoice (date of purchase and dealer’s stamp).
• Please send the product well packed to the appropriate Service Centre.

Repair service:

• Outside the warranty period.
• Defects not covered by the warranty.
• Ask your nearest service station for the possibility of repair.

Further information: http://www.steinel.de

References

• Steinel Group | STEINEL
• International | STEINEL
• STEINEL | Steinel Grupul
• Sensorer | Sensorstyrd belysning från Steinel l KHS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>