Fms 1:18 Chevrolet Chevy K-10 Scaler Rtr Car Kit Instruction Manual
- June 5, 2024
- Fms
Table of Contents
- Introduction
- Transmitter instruction
- Transmitter Battery Installation
- Warnings
- Power On
- Instructions
- Transmitter specification
- Throttle stick position
- Operating the vehicle
- Setting the Gear Mesh
- Charging the Battery
- Spare parts list
- CE Warning
- Appendix 1 FCC Statement
- Declaration of Conformity (DoC)
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
1:18
CHEVROLET K10
Instruction Manual
Introduction
Every Chevrolet truck has its own story behind it. Pickup trucks have always
been an American car culture and the symbol of the American spirit. This was
until GM’s brought a new set of naming principles – the C for rear-wheel drive
and the K for a four-wheel-drive into their all-new lineup of Chevrolet
pickups.
With a tailgate that lowers the loading height, a spacious cab, and a sunken
frame, FMS’new 1:18 CHEVROLET
K10 adheres to the revolutionary “square body” and features a perfectly
replicated K series in terms of 4wd, metal beams, aluminum frame rails, and a
reliable multi-link suspension system.
RC model pickups with hard plastic bodyshells are rare and precious when
mostly SUVs dominate the area. The large cargo space and retractable tailgate
make it easy to carry all kinds of 1/18 simulation parts such as motorcycles,
kayaks, and various camping equipment.
As a perfect 1/18 duplicate, the FMS CHEVROLET K10 shares the same linear
design as the real car, as well as a curved grille and outside front bumper.
Elegant detailing with a premium two-tone color scheme, the body’s mirrors,
and front and rear bumpers. Move the camera and focus on the spacious and
comfortable car’s interior, from the bench seats to the center console and
steering wheel. Open the hood and explore the large inside space where the
motor, ESC, receiver, and battery are readily accessible, making upgrading an
easy task. Light sets have linked light control functions with light control
plug-ins including headlights, turn signals and reverse lights.
Scale replica K10 tires and wheels as featured on the real truck, molded in a
soft all-terrain pattern for running on any terrain.
The 1/18 Chevrolet K10 – is perfect as a static model until you switch on and
imagine yourself behind the wheel of a legendary Chevy pickup! A surprise gift
from FMS for you in 2021.
Transmitter instruction
[1]| A/B Mode switch key| [7]| Throttle trim + (TH TRIM +) mode A / light
control switch 1 mode B
---|---|---|---
[2]| Re-set button(F.Reset)Mode A| [8]| Throttle trim – (TH TRIM -) mode A /
light control switch 2 mode B
[3]| Steering Trim+(ST TRIM+)Mode A| [9]| Channel 6 (reserved)
[4]| Steering Trim-(ST TRIM-) Mode A| [10]| Steering wheel
[5]| Power Switch| [11]| Throttle trigger
[6]| Reverse key mode a / steering angle limit mode B| |
A/B mode function toggle switch
F.Reset| In the use of the disorder settings, not back to the normal state,
you can use Factory. Reset function| Make sure that the mode function toggle
switch is in mode A, hold the steering wheel left or right, and click the F.
Reset button at the same time. After two clicks, it means that the factory
settings have been completed.
REV| After replacing the steering gear, the steering gear is reversed| Make
sure that the mode function toggle switch is in mode A, twist the left or
right steering wheel, and click the Rev button at the same time. After
ringing, it means that the reverse setting of the steering gear has been
completed.
After replacing the motor, there is a reverse| Make sure that the mode
function toggle switch is in mode A, pull or push the throttle, and click the
Rev button at the same time. After ringing, it means that the motor reverse
setting has been completed.
Adjust 30 / 50 / 100% steering radian| Make sure that the mode function toggle
switch is in mode B, and click the ST Angle key. After a click, it means that
the 30% steering radian has been set. Click the ST Angle button again, and you
will hear two beeps, indicating that the setting of 50% steering radian has
been completed. Click the ST Angle button again, and you will hear three
beeps, indicating that the 100% steering radian has been set. Then click to
cycle to a click to indicate that the 30% steering radian has been set.
ST TRIM| When the steering center is not centered| Make sure that the mode
function toggle switch is in mode A, press ST TRIM+ or – button to fine tune
the steering center. Every click of the button will ring. When the maximum and
minimum values are reached, a long sound will appear. When the median value is
reached, it will ring twice.
THE TRIM| When the throttle is not centered| Make sure that the mode function
toggle switch is in mode A, press the TH TRIM + / – button to fine tune the
throttle center. Every click of the button will ring. When reaching the
maximum and minimum value, the button will ring, when reaching the median
value, the button ring twice.
LED| Light setting| Make sure that the mode function toggle switch is in mode
B, click the LED button, and the headlamp will be on after a click. Then click
the LED button, and the headlight will be highlighted after two clicks.
Continue to click the LED button, and the air defense light will be on after
three rings.
Emitter: forget the reminder| If the transmitter does not receive any command,
it will give an alarm after 10 minutes and enter sleep mode after 2 minutes
Transmitter: frequency alert| When the transmitter does not match the
receiver, the indicator light of the transmitter keeps flashing
Transmitter: no frequency matching + low power reminder 4.5V| The indicator
light of the transmitter flashes slowly and makes a sound
Transmitter: low power reminder 4.5V| The indicator light of the transmitter
flashes slowly
Car: frequency alert| The headlights keep flashing
Car: low power alarm 6.3-6.4v| All lights keep flashing, steering and throttle
are not controlled
Car: reminders to prevent forgetting| If the vehicle does not receive any
signal, it will flash back and forth after 10 minutes and enter sleep mode
after 2 minutes
| | |
Times for Pressing
| | |
---|---|---|---|---|---|---
Button| Light Position| Function| I| II| III| IV| V| Control Mod| Remarks|
LED+| Headlight| Always on| OFF| •| OFF| OFF| OFF| | |
Always Off| OFF| OFF| •| •| OFF| | |
| Reversing light| | | | | | Throttle linkage control| |
Turn Signal| Left turn signal| OFF| | | OFF| | Direction linkage controL| The
light is on when reversing|
Right turn signal| OFF| | | OFF| | Direction linkage controL| |
Emergency Flashers| OFF| OFF| OFF| •| OFF| | |
Transmitter Battery Installation
Battery Type: AAA
Battery Installation:
- Open the battery compartment cover.
- Insert 4 fully-charged AAA batteries into the compartment. Make sure that the battery makes good contact with the battery compartment’s contacts.
- Replace the battery compartment cover.
Low battery alarm: When the battery is lower than 4.2V, the LED on the panel
will flash slowly.
Note: When installing the batteries, be careful to handle the positive
and negative poles. (As shown in the picture on the right)
Warnings
- This vehicle is not intended for those under 14 years of age without proper adult supervision.
- It is not a toy! Failure to operate or maintain this vehicle in a safe manner can result in bodily harm.
- Replace damaged components with original factory parts. Pay special attention to the polarity of all vehicle wiring.
- Only use approved 2-cell lithium polymer batteries. Do not over-charge or over-discharge the battery as doing so may cause the battery to become a fire hazard. If the battery should become hot during charging, discontinue charging immediately and disconnect the battery from the charger.
- Never leave the battery unattended while charging. If you are unsure of how to charge this battery, please seek the advice of experienced RC users. Never let children charge the battery without adult supervision.
- The motor will become hot during use. Allow 10-15 minutes between runs for the vehicle to cool down. Doing so will prolong the life of your vehicle.
- Use common sense when selecting the environment to operate your vehicle. Do not operate near power cables, cellular/radio towers, deep water or unstable terrain. The operator is solely responsible for their actions.
- The product is composed of precision electrical components. It is critical to keep the product away from moisture and other contaminants. If exposed to a humid environment, make sure the electronics are fully dried prior to using them again.
- Always check the radio range of the vehicle prior to operation in order to prevent radio loss or interference.
- Operate this product within your ability. If the vehicle is dangerous to retrieve, it’s never worth the risk.
- Always turn on the transmitter before connecting the battery on the model. When turning off the model, always disconnect the battery first, and then turn off the model, always disconnect the battery first, and then turn off the transmitter. If this order is reversed, the model may become uncontrollable and cause serious damage.
- Never allow transmitter batteries to run low as it may cause loss of vehicle control.
- Plastics on the vehicle are susceptible to damage or deformation due to extreme heat and cold climate. Do not store the model near any source of heat such as an oven or heater. Store the model indoors, in a climate-controlled, room temperature environment.
- Never shorten the receiver antenna; this may affect the transmitting range of the radio system.
- Only use specified batteries (X4 AAA batteries).
- Do not open, disassemble, or attempt to repair the battery.
- Do not crush/puncture the battery, or short the external contacts.
- Do not expose to excessive heat or liquids.
- Do not drop the battery or expose to strong shocks or vibrations.
- Always store the battery in a cool, dry place.
- Do not use the battery if damaged.
- The Battey must be disconnected from the receiver when charging.
Power On
Follow the steps below to turn on the transmitter:
- Check to make sure that that battery is fully charged and installed correctly.
- Toggle the switch to the [ON] position. When active the R.LED will be lit.
- Connect the receiver to power.
• For safety always powers on the transmitter before the receiver.
Note
Operate with caution in order to avoid damage or injury.
Make sure that the throttle is at its lowest position and the switches are set
to their up position.
Instructions
After setting up, follow the instructions below to operate the system.
-
Automatic code matching (the transmitter and receiver have been successfully coded before leaving the factory.)
If you need to replace another transmitter or receiver, please follow the following steps to code:
1. When the transmitter power is on and the code matching mode is on, the light keeps flashing;
2. The power supply of the receiving board is turned on, and the front lights keep flashing to enter the code matching mode;
3. When the code matching is successful, all the transmitter lights are on and all the lights on the car are off;
Note: when code matching, please operate the transmitter to enter the code matching state first, and then operate the receiver to enter the code matching state. -
POWER OFF
Follow the steps below to turn off the system:
1. Disconnect the receiver power.
2. Toggle the transmitter’s power switch to the off position.
Note
Make sure to disconnect the receiver power before turning off the transmitter.
Failure to do so may lead to damage or serious injury.
Transmitter specification
Product Model | HT-TX02 |
---|---|
Adaptive model | Car |
RF | 2.4GHz |
Transmitting power | <20dBm |
Wireless protocol | ANT |
Distance | >100m(ground) |
Channel Resolution | 256 Grade |
Battery | 6V DC 1.5AAA*4 |
Charging Interface | NO |
Lifetime | According to battery type |
Low Voltage Warning | <4.45V |
Antenna Type | Built-in single antenna |
Data interface | NO |
Temperature Range | -10°C – +60°C |
Humidity Range | 20-95% |
Online Update | NO |
Color | Black |
Size | 152mm 75mm 167mm |
Weight | 160g |
Certification | CE, FCC ID: 2AUBX-HT-TX02 |
Throttle stick position
Operating the vehicle
Step 1: turn on the transmitter, the headlamp of the transmitter will flash and
enter the frequency matching mode.
Step 2: turn on the receiver switch, the headlight will flash and enter the
frequency matching mode.
Step 3: when the transmitter and receiver are successful in frequency up, the
front lights of the transmitter will be on for a long time, and the front
lights of the vehicle will be off.
Setting the Gear Mesh
The gear mesh is the clearance between the pinion and spur gears in your vehicle. If the motor or gearing components are replaced, check that the gears are not meshing too tightly as this may cause premature wear.
Charging the Battery
- Connect the charger to a USB port then connect the battery to the charger.
- When charging, the Green LED is flash, when charged, the Green LED is stable.
- Do not let the battery charge unattended!
- If the battery or charger is hot, disconnect the battery and charger immediately as this may be caused by an internal short-circuit.
-
Always charge LiPo batteries on non-flammable, heat-resistant surfaces.
-
Always use a LiPo-safe bag or container while charging. Do not allow LiPo cells to overheat at any time.
Cells that reach greater than 140 Fahrenheit(60°C) will usually become damaged and will catch fire. -
Do not charge the LiPo pack while it is still in the model. Never charge or store battery packs in a vehicle.
-
Do not discharge LiPo; doing so will damage the battery.
-
Do not expose LiPo cells to water or moisture at any time.
-
Do not store battery near open flame or heater.
-
Do not assemble LiPo cells or pre-assembled packs together with other LiPo cells or packs.
-
Always store LiPo batteries in a secure location away from children.
-
Always remove the LiPo battery if the model is involved in any kind of crash.
-
Carefully inspect the battery and connectors for even the smallest damage.
-
CAUTION: Cells may become hot after usage. Allow the pack to cool to room temperature prior to recharging.
-
Do not allow the electrolyte to get into the eyes or on the skin. Wash affected areas immediately if they come into contact with electrolytes.
Do not alter or modify connectors or wires of a LiPo battery pack. -
Always inspect the condition of the battery before charging and operating.
-
Do not short circuit the LiPo battery.
-
Do not have contact with a leaky/damaged battery directly.
-
Do not charge the battery out of recommended temperature range(O°C 45°C).
NOTE
- If it is not in use for a long time, unplug and take off the battery to prevent battery leakage.
- Do not open, disassemble, or attempt to repair the battery.
- Please disconnect the battery from the receiver before charging.
Spare parts list
C2110 | 1:18 CHEVROLET K10 Hood RED/WHITE |
---|---|
C2111 | 1:18 CHEVROLET K10 Front and Rear Light Cup Set |
C2112 | 1:18 CHEVROLET K10 Hood Mount Set |
C2113 | 1:18 CHEVROLET K10 Rearview Mirror And Wiper |
C2114 | 1:18 CHEVROLET K10 Bumper And Side Panel |
C2115 | 1:18 CHEVROLET K10 Lens |
C2116 | 1:18 CHEVROLET K10 Body SHELL |
C2117 | 1:18 CHEVROLET K10 CHASSIS |
C2118 | 1:18 CHEVROLET K10 HANDLE |
C2118 | 1:18 Cooper Tire 19.2 x 13.5 x 56 |
C2119 | Eight Planets Style Wheels plastic parts |
C2052 | FMS LIPO Battery 2S LIPO 380mAh for 1:18 |
C2123 | 1:18 CHEVROLET K10 Light set |
C2051 | FMS USB Charger |
C2049 | 1:18 050 Motor set |
C2057 | 1:18 Plastic Gear set |
C2124 | 1:18 CHEVROLET K10 Transmission Shaft full set |
C2102 | 1:18 SCREW SET |
C2021 | 1:18 1KG High Torque 3wire Servo |
--- | --- |
C2125 | 1:18 CHEVROLET K10 Window |
C2074 | 1:18 Rear Wheel Shaft |
C2071 | 1:18 Wheel Hex |
C2063 | 1:18 SHOCK PLASTIC PARTS |
C2064 | 1:18 KATANA V2 / LC80 LAND CRUISER/ FJ Cruiser Connecting Rod |
C2133 | 1:18 M4 BALL HEAD |
C2066 | 1:18 BALL HEAD |
C2067 | 1:18 Steering Hub & Spindle |
C2068 | 1:18 FRONT/REAR AXLE parts |
C2069 | 1:18 SERVO HORN |
C2126 | 1:18 CHEVROLET K10 MIRROR LENS |
C2075 | 1:18 FRONT OUTDRIVE SHAFT |
C2076 | 1:18 Gear Box Plastic Parts |
CE Warning
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all .persons and must not be co- located or operating in conjunction with any other transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
Appendix 1 FCC Statement
FCC ID: 2AUBX-HT-TX02
This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.
-
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance. -
Move all your channels to the desired position.
-
Select [All channels] and then [Yes] in the confirmation box.
Declaration of Conformity (DoC)
We,
Dongguan Solid Model Technology Co.,Ltd
3/F, Building B, 3rd Industry Zone,
Matigang, Dalingshan Town
Dongguan City of China 523810. declare under our responsibility that the
product:
Type of Equipment: Driving System & 2.4GHz Control System
Brand Name: FMS
Compatible for cars: 1:18 CHEVROLET K10
Equipment Model: 11808
Phone:0769-86976655
Web:www.fmsmodel.com
to which this declaration relates is in conformity with the essential requirements and other relevant requirements of the Directive 2014/53/EU, EMC Directive 2014/30/EU, EMC Directive 2014/53/EU, FCC Indentifier 2AUBX-HT-TX02, EU RoHS Directive 2011/65/EU, and Council Directive 2014/30/EU. The product is in conformity with the following standards and/or other normative documents:
ETSI EN 301 489-1 V2.2.3(2019-11)
ETSI EN 301 489-17 V3.2.4(2020-09)
EN 55032:2015+A11:2020
EN 55035:2017+A11:2020
EN61000-3-2:2014
EN61000-3-3:2013
EN : 62479:2010
ETSI EN 300 328 V2.2.2 (2019-07)
DISTRIBUTOR
North America:
Horizon Hobby LLC
2904 Research Road
Champaign, IL 61822, USA
Tel.: 217-403-3584| Sweden:
Minicars Hobby Distribution AB
Annelundsgatan 17C
749 40 Enköping, Sweden
Tel.: +46-171-14 30 02
---|---
The United Kingdom:
CML Distribution Ltd
Saxon House, Saxon Business Park, Hanbury Road
Bromsgrove, Worcestershire
B60 4AD, England
Tel.: +44 (0)1527 575349| Australia:
Model Engines Pty Ltd
Unit 1/32 Bluett Drive
Smeaton Grange
NSW 2567 Australia
Tel.: +61(0)411128284
VERTEILER
Germany, Austria:
D-Power Modellbau
Sürther Str. 92-94
D-50996 Köln
Germany
Tel.: (0221) 346 641 57| DISTRIBUTEUR
France, Benelux :
Beez2B sprl
54 rue de Thy
B-1470 Baisy Thy
Belgique 3 Tél. : +32 2 376 71 82
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>