Quest WTX Wireless Transmitter Audio System User Manual
- June 5, 2024
- Quest
Table of Contents
WTX Wireless Transmitter Audio System
User Manual
INTRODUCTION
Mounting a WTX.
Place the WTX on the rod and wrap the rubber band from down side of the rod. Or use Velcro tapes on flat surfaces such as detector control
Connecting the WTX with Detectors.
Power on/off a WTX.
Press the power button once to turn on the transmitter. Hold for 2 seconds to turn it off.
SPECIFICATIONS
HOW TO WORK?
1. If the transmitter works with Receiver WRX
1.1 CONNECT A RECEIVER WRX. Insert the 6.35mm or 1/4” jack of the wire
headphones into the female port of WRX.
1.2 POWER ON THE TRANSMITTER.
1.3 POWER ON THE RECEIVER WRX AND PAIR IT WITH THE TRANSMITTER. Hold the knob and turn to clockwise direction to turn it on. Keep turning to set the volume higher. Turn it anti-clockwise direction to set the volume lower. Turn it to the end to power off.
The WRX will pair with the last transmitter automatically. Quick turn the WRX “on-off-on” to pair a new transmitter.
2. If the transmitter WTX works with Lite Headphones
2.1 HEADPHONE ADJUSTMENT
Before wearing the lite headphone for the first time you should adjust it
properly to achieve the best sound and ambient noise attenuation.
Unfold the headphone pad as the figure 1. and 2. Select the appropriate lock- in position on both sides of the headband as figure 3. The pads will adjust the angle automatically according to your head size.
2.2 POWER ON TRANSMITTER
Make sure the transmitter is fully charged and press the power button for 1
second. The LED indicator will start to flash. The battery condition LED will
indicate the battery life for 3 seconds.
2.3 POWER ON HEADPHONE
Make sure the headphones are fully charged and press the power button (between
two volume buttons) for 1 second. The LED indicator will start to flash.
2.4 PARING (when necessary)
If you need to pair them again, please place the Lite Headphones to within
10cm of the transmitter, press and release the power button of the headphone
quickly. The LED indicator of the transmitter will change to steady condition.
3. If the transmitter works with Pro Headphones
3.1 POWER ON THE TRANSMITTER
Make sure the transmitter is fully charged and press the power button for 1
second. The LED indicator will start to flash RED light. The LED indicator
will turn to still when connected with the Pro headphones.
3.2 POWER ON THE PRO HEADPHONES
Keep press the power button for 2 seconds to power on. The status LED will
start blinking when powered on. The headphones will connect with the last
paired transmitter (powered on condition) automatically.
3.3 PARING (when necessary)
When the Pro headphones is not connected with the last transmitter it will
blink at a fast frequency. You just need to press the headphones power button
once quickly near the new transmitter (powered on condition). The headphones
LED will blinks at a slow frequency when pairing successfully.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition, compliance with
exposure requirements.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>