Cabela s GS-100 Training Collar User Guide

June 3, 2024
Cabela s

Cabela s -logo

FPO
GUN DOG
TRAINING COLLAR GS-100

OPERATING GUIDE
PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING

IMPORTANT SAFETY INFORMATION

EXPLANATION OF ATTENTION WORDS AND SYMBOLS USED IN THIS GUIDE
**** This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION CAUTION, used without a safety alert symbol, indicates a hazardous situation that, if not avoided, could result in harm to your dog.

WARNING

  • Not for use with aggressive dogs. Do not use this product if your dog is aggressive, or if your dog is prone to aggressive behavior. Aggressive dogs can cause severe injury and even death to their owner and others. If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or a certified trainer.
  • This device contains Lithium-Ion (Li-Ion) batteries; DON’T attempt to cut into or pry open the battery. Be sure to discard any used batteries properly.
  • Never incinerate, puncture, deform, short-circuit or charge with an inappropriate charger. Fire, explosion, property damage, or bodily harm may occur if this warning is not followed.
  • There is a risk of explosion if a battery is replaced by an incorrect type. Do not short circuit, mix old and new batteries, dispose of in a fire, or expose them to water. When batteries are stored or disposed of, they must be protected from shorting.
  • The battery should be charged in areas with temperatures ranging from 32°F to 100°F / 0°C to 38°C. Recharging the battery outside of this temperature range can cause the battery to overheat, explode, or catch fire.

CAUTION

  • Proper fit of the collar is important. A collar worn for too long or made too tight on the dog’s neck may cause skin damage ranging from redness to pressure ulcers. This condition is commonly known as bed sores.

  • Avoid leaving the collar on the dog for more than 12 hours per day.

  • When possible, reposition the collar on the dog’s neck every 1 to 2 hours.

  • Check the fit to prevent excessive pressure; follow the instructions in this manual.

  • Never connect a lead/leash to the electronic collar; it will cause excessive pressure on the contacts.

  • When using a separate collar for a lead/leash, don’t put pressure on the electronic collar.

  • Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.

  • Examine the contact area daily for signs of a rash or a sore.

  • If a rash or sore is found, discontinue the use of the collar until the skin has healed.

  • If the condition persists beyond 48 hours, see your veterinarian.
    For additional information on bed sores and pressure necrosis, please visit the Support section for remote trainers at support.sportdog.com.
    These steps will help keep your dog safe and comfortable. Millions of dogs are comfortable when they wear stainless steel contacts. Some dogs are sensitive to contact pressure. You may find after some time that your dog is very tolerant of the collar. If so, you may relax some of these precautions. It is important to continue daily checks of the contact area. If redness or sores are found, discontinue use until the skin has fully healed.

  • You may need to trim the hair in the area of the Contact Points or switch to the longer Contact Points to ensure consistent contact. Never shave the dog’s neck; this may lead to a rash or infection.

  • You should not make the collar any tighter than is required for good contact. A collar that is too tight will increase the risk of pressure necrosis in the contact area.

Thank you for choosing this Cabela’s® training collar. Used properly, this product will help you train your dog efficiently and safely. To ensure your satisfaction, please review this Operating Guide thoroughly. If you have questions regarding this product’s operation, contact the Customer Care Center at 1-800-732-0144, or visit cabelas.com or basspro.com.
To get the most protection out of your Year Warranty, please register your product within 30 days at sportdog.com/cabelasgundog. By registering and keeping your receipt, you will enjoy the product’s full warranty and, should you ever need to call the Customer Care Center, we will be able to help you faster. Most importantly, your valuable information will never be given or sold to anyone. Complete warranty information is available online at sportdog.com/support/warranty.

COMPONENTS

Cabela s GS 100 Training Collar-fig1

HOW THE SYSTEM WORKS

The Cabela’s® GS-100 has been proven safe, comfortable, and effective for all dogs over 8 pounds. Consistent, correct use of this product allows you to reinforce commands and correct misbehavior from up to 100 yards. The Remote Transmitter sends a signal, activating the Collar Receiver to deliver a harmless stimulation. With proper training, a dog will learn to associate this signal with a command. This model features adjustable static stimulation levels so you can tailor the stimulation level to your dog’s temperament, eliminating the risk of over-correction.
IMPORTANT: the Cabela’s GS-100 has a range of up to 100 yards. Depending on the way you hold the remote transmitter, the maximum range may vary. For consistent results at longer ranges, hold the remote transmitter in a vertical position away from your body and above your head. Terrain, weather, vegetation, transmission from other radio devices, and other factors will affect the maximum range.

WARNING Do not use this product if your dog is aggressive, or if your dog is prone to aggressive behavior. Aggressive dogs can cause severe injury and even death to their owner and others. If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or a certified trainer.

KEY DEFINITIONS

Cabela s GS 100 Training Collar-fig3|
---|---

REMOTE TRANSMITTER: Transmits the radio signal to the Collar Receiver. It is waterproof and can be submerged in water to a depth of 25 feet.
LCD: Indicates battery level and stimulation level.
FRONT BUTTON: This button is factory-set to deliver continuous static stimulation; Level 00 will deliver tone stimulation.
SIDE BUTTONS: These two buttons adjust the level of stimulation (00 = tone stimulation; 1-10 = continuous static stimulation).
CHARGING JACK: For connecting the charger. Although the Remote Transmitter is waterproof without it, keep the cover in place when not charging to keep debris out
of the opening.
COLLAR RECEIVER: Receives the radio signal from the Remote Transmitter and delivers the static or tone stimulation for correcting or cueing your dog. It is waterproof and can be submerged in water to a depth of 25 feet.
RECEIVER INDICATOR LIGHT: Indicates when the Collar The receiver has been turned on or off, and serves as a low battery indicator, and also indicates when continuous static or tone stimulation is given.
CONTACT POINTS: The contacts through which the Collar Receiver delivers stimulation.
ON/OFF BUTTON: Momentarily pressing and releasing this button turns the Collar Receiver on and off.

THE COLLAR RECEIVER IS CAPABLE OF DELIVERING TWO TYPES OF STIMULATION:
CONTINUOUS: You control both when and how long static stimulation is delivered, up to a maximum of 10 seconds. After 10 seconds, the stimulation will “time out” and the Front Button needs to be released and then pressed again before additional static stimulation can be delivered.
TONE: The Collar Receiver will make a rapid beeping noise when the Front Button is pressed (Side Button set to 00).*

  • Tone comes preset and is not adjustable.

STEP :: 01

PREPARE THE REMOTE TRANSMITTER

CHARGE THE REMOTE TRANSMITTER

  1. Lift the rubber cover protecting the Charging Jack
  2. Connect one of the charger connectors to the Charging Jack.
  3. Plug the charger into a standard 120/240-volt AC wall outlet.
  4. Charge the Remote Transmitter for 2 hours for the first charge and every charge thereafter. Using Li-Ion technology, the Remote Transmitter only requires a 2-hour charge. It is not harmful to let the unit charge for more than 2 hours.
  5. When charging is complete, remove the charger connector, and replace the rubber cover. The unit will perform a brief LCD test, and revert back to the normal LCD screen.
    NOTE: Approximate battery life between charges is 50 to 70 hours, depending on the frequency of use.

Cabela s GS 100 Training Collar-fig5

TRANSMITTER LCD

Cabela s GS 100 Training Collar-fig6

NOTE: The Remote Transmitter’s backlight turns off after 5 seconds to conserve battery life; the LCD display automatically turns off after approximately 30 minutes.

STEP:: 02

PREPARE THE COLLAR RECEIVER
CHARGE THE COLLAR RECEIVER

  1. Align the Charging Cradle with the Charging Contacts as shown in the image. Push down on the Charging Cradle until it snaps into place.
  2. Plug the USB Adaptor into a power source. The Indicator Light will be solid green while charging. During charging, keep the GS-100 in an open, well-ventilated area.
  3. Charge the Collar Receiver for 2 hours for the first charge and every charge thereafter. The Indicator Light will flash green once charging is complete.
  4. Remove the Charging Cradle from the GS-100 and unplug the USB Adaptor from the power source.

Using Li-Ion technology, the Collar Receiver only requires a 2-hour charge. It is not harmful to let the unit charge for more than 2 hours.
TO TURN THE COLLAR RECEIVER ON
Press and release the On/Off Button (located between the Contact Points). The Receiver Indicator Light will come on and the Collar Receiver emits a start-up tone.
TO TURN THE COLLAR RECEIVER OFF
Press and release the On/Off Button. Ther Receiver Indicator Light comes on solid (red) and the Collar Receiver emits an off-tone.
To extend the life between charging cycles, turn the Collar Receiver off when it is not in use.
NOTE: Approximate battery life between charges is 20 to 25 hours, depending on the frequency of use.

COLLAR RECEIVER INDICATOR LIGHT

COLLAR RECEIVER INDICATOR LIGHT

OPERATIONAL MODE| LIGHT COLOR| BATTERY STATUS| LIGHT FUNCTION| SPEAKER FUNCTION
Unit is turned on via On/Off Button| Green| Good| Light is solid in color during the beep sequence| Emits start-up tone
Unit is turned on via On/Off Button| Red| Low| Light is solid in color during the beep sequence| Emits start-up tone
Unit is turned off via On/Off Button| Red| N/A| Light is solid in color during the beep sequence| Emits off-tone
Unit is on| Green| Good| Light flashes every 2 seconds| N/A
Unit is on| Red| Low| Light flashes every 2 seconds| N/A
Unit is delivering continuous static stimulation| Red| N/A| Light quickly flashes for as long as the button is pressed (up to 10 seconds)| N/A
Unit is delivering tone stimulation| Green| N/A| __ Light quickly flashes for

as long as the button is pressed

| Unit will beep for as long as the button is pressed
Unit is charging| Green| Low| Light is solid in color while on the charger| N/A
Unit is fully charged (charger still connected)| Green| Good| Light flashes once per second once the battery is completely charged| __ N/A

RECHARGEABLE BATTERIES

WARNING

  • This device contains Lithium-Ion (Li-Ion) batteries; DON’T attempt to cut into or pry open the battery. Be sure to discard any used batteries properly.
  • Never incinerate, puncture, deform, short-circuit or charge with an inappropriate charger. Fire, explosion, property damage, or bodily harm may occur if this warning is not followed.
  • There is a risk of explosion if a battery is replaced by an incorrect type. Do not short circuit, mix old and new batteries, dispose of in a fire, or expose them to water. When batteries are stored or disposed of, they must be protected from shorting.
  • The battery should be charged in areas with temperatures ranging from 32°F to 100°F / 0°C to 38°C. Recharging the battery outside of this temperature range can cause the battery to overheat, explode, or catch fire.
  • The rechargeable Lithium Ion (Li-Ion) batteries are not memory sensitive, do not require depletion before charging, and cannot be overcharged.
  • The batteries come partially charged from the factory but will require a full charge before the first use.
  • When storing the unit for long periods, remember to regularly give batteries a full charge. This should be done once every 3 to 4 months.
  • You should expect hundreds of recharge cycles from your batteries. However, all rechargeable batteries lose capacity over time relative to the number of recharge cycles they experience. This is normal. If your operating time drops to half of the original life, contact the Customer Care Center to purchase a new battery.
  • The batteries should last for a period of 3-5 years. When a battery needs replacement, you can order a new pack by calling the Customer Care Center at 1-800-732-0144. Please do not open the Collar Receiver or Remote Transmitter until you have received the replacement.

STEP:: 03

FIT THE COLLAR RECEIVER
IMPORTANT: The proper fit and placement of the Collar Receiver is important for effective operation. The Contact Points must have direct contact with your dog’s skin.
CAUTION See page 3 for Important Safety Information.

To ensure a proper fit, follow these steps:

  1. Make sure the unit is off.

  2. With your dog standing (3A), center the Collar Receiver so the Contact Points are underneath your dog’s neck, touching the skin (3B). If your dog has a long or thick coat, you have 2 options to ensure consistent contact: either trim the hair around the Contact Points or switch to the longer Contact Points included with your system.

  3. Check the tightness of the collar by inserting your finger between the end of a Contact Point and your dog’s neck (3C). The fit should be snug but not constricting.

  4. Allow your dog to wear the collar for several minutes and then recheck the fit. Check the fit again as your dog becomes more comfortable wearing the collar.

CAUTION

  • You may need to trim the hair in the area of the Contact Points. Never shave the dog’s neck; this may lead to a rash or infection.
  • You should not make the collar any tighter than is required for good contact. A collar that is too tight will increase the risk of pressure necrosis in the contact area.

STEP:: 04

FIND THE BEST INTENSITY LEVEL FOR YOUR DOG

The Cabela’s® GS-100 has multiple intensity levels. This allows you to choose the static stimulation that is best for your dog.
NOTE: Always start at the lowest level and work your way up.
For training efficiency, it is important to find the right intensity level for your dog. This is called the Recognition Level, at which your dog looks around in curiosity or flicks his ears.
FINDING YOUR DOG’S RECOGNITION LEVEL:
NOTE: Every dog is different and you cannot predict where your dog’s Recognition Level will be. Watch closely for any slight change in behavior that demonstrates your dog is feeling the static stimulation.

  1. With the Collar, Receiver turned on and properly fitted to your dog, set the Remote Transmitter to Level 1 and press the Front Button for 1 to 2 seconds.
  2. If your dog shows no reaction to Level 1, go to Level 2 and repeat the process.
  3. YOUR DOG SHOULD NOT VOCALIZE OR PANIC WHEN RECEIVING STATIC STIMULATION. IF THIS HAPPENS, THE STATIC STIMULATION LEVEL IS TOO HIGH AND YOU NEED TO GO BACK TO THE PREVIOUS LEVEL AND REPEAT THE PROCESS.
  4. Once you find your dog’s Recognition Level, this is the level you should use when you begin a training exercise.
  5. If you have progressed to Level 10 while searching for your dog’s Recognition Level and your dog continues to show no response, check to see if the Collar Receiver is snug against your dog’s neck. Then go back to Level 1 and repeat the process. If your dog still does not indicate he is feeling the static stimulation, you have two options: trim the hair beneath the Contact Points or switch to the longer Contact Points included in your system.
    If after completing all of these steps your dog still does not indicate he is feeling the stimulation, please contact the Customer Care Center at 1-800-732-0144.

GENERAL TRAINING TIPS

BEFORE TRAINING YOUR DOG WITH THIS PRODUCT:
You will have the most success using this remote trainer if you always remember to teach a command before trying to reinforce the command with a remote trainer. In addition, always keep the following training tips in mind:

  • Eliminate one misbehavior or teach one obedience command at a time. If you move too fast with the training, your dog may become confused.

  • Be consistent. Give your dog a tone or static stimulation with each misbehavior.

  • Do not overcorrect your dog. Use as few stimulations as possible to train your dog.

  • Restrict your dog from situations in which he has a history of misbehaving unless you can supervise him and use the Remote Trainer for applying tone or static stimulation.

  • If you notice one situation in which your dog misbehaves repeatedly, set up this situation as a training session.
    This will dramatically increase your chances of success.

  • If your dog has a timid reaction to the tone or static stimulation (especially the first couple of times), do not be alarmed. Redirect his attention to a simple and appropriate behavior (i.e. a known command, such as “Sit”).

  • Never use the Remote Trainer to correct or eliminate any form of aggressive behavior. If your dog exhibits such behavior, contact a professional trainer. Aggression in dogs is the result of many factors – it may be a learned behavior or it may be brought on as a result of fear. Another factor contributing to aggression in dogs is social dominance. Every dog is different.
    At this point, your remote trainer is ready to use.

STEP :: 05

MATCH THE COLLAR RECEIVER AND REMOTE TRANSMITTER
To match the Collar Receiver to work with a new Remote Transmitter or to match a new Collar Receiver to work with your existing Remote Transmitter:
A. Turn the Collar Receiver off.
B. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn off after 4-5 seconds. If the On/Off Button is released too early, the Receiver Indicator Light will begin flashing as normal. If this occurs, start over from A.
C. After the Receiver Indicator Light has turned off, release the On/Off Button.
D. Press and hold the Front Button on the Remote Transmitter until the Receiver Indicator Light flashes 5 times. Once the Receiver Indicator Light has flashed 5 times, the Collar Receiver has been matched and will begin flashing as normal. If the Receiver Indicator Light does not flash 5 times, start over from A.

TEST LIGHT TOOL INSTRUCTIONS

You can verify that the Collar Receiver is delivering static stimulation to your dog by placing the Test Light Tool, enclosed in your kit, on the Collar Receiver.

  1. Turn the Collar Receiver on.

  2. Press the Test Light Tool Contacts to the Contact Points of the Collar Receiver.

  3. Press the Static Stimulation Button/Front Button on the Remote Transmitter.

  4. The Test Light will flash.
    NOTE: At higher static stimulation levels, the Test Light will flash brighter.

  5. Turn the Collar Receiver off.

Save the Test Light Tool for future testing.
NOTE: If the Test Light does not flash, recharge the battery and retest.
If the Test Light still does not flash, contact the Customer Care Center at 1-800-732-0144.

ACCESSORIES

To purchase additional accessories for the GS-100, contact the Customer Care Center at 1-800-732-0144. COMPONENT| PART NUMBER
---|---
3⁄4” Black Collar Strap| SAC00-10816
Collar Receiver (does not include collar strap)| SDT17-17686
Remote Transmitter| SDT17-17697
Contact Points (Short)| SAC00-12571
Contact Points (Long)| SAC00-12570
Battery Kit (Collar Receiver)| SAC54-16718
Battery Kit (Remote Transmitter)| SAC54-13734
Wall Charger| SAC00-16841
Charging Cable| SDT54-16717

FREQUENTLY ASKED QUESTIONS

Is the stimulation safe for my dog?

– While static stimulation may be unpleasant, it is harmless to your dog. Electronic training devices require interaction and training from the owner to achieve desired results.

How old does a dog have to be before using the GS-100?

– Your dog should be able to learn basic obedience commands such as “Sit” or “Stay.” The Collar Receiver may be too large for dogs under 8 pounds.

Once my dog is trained and has been obeying my commands, will my dog have to continue to wear the Collar Receiver?

– Your dog may need to wear the Collar Receiver from time to time for reinforcement. Also, many hunters keep the Collar Receiver on their dogs while hunting for maximum control.

Is the Collar Receiver waterproof?

– Yes. If the rechargeable battery pack ever needs to be replaced, make sure the o-ring and o-ring groove are free from dirt and debris.

Can my Collar Receiver be used around salt water?

– Yes. However, if the Collar Receiver is used in or around salt water, it should be rinsed with fresh water following each use.

Can I use the GS-100 with more than one dog?

– No. The GS-100 is only a one-dog system.

Can I use the GS-100 on aggressive dogs?

– We do not recommend any of our products to be used on aggressive dogs. We recommend you contact your local veterinarian, or professional trainer to determine if your dog might be aggressive.

Will I get exactly 100 yards of range with the GS-100?

– The range you get with your GS-100 will vary according to terrain, weather, and vegetation as well as transmission from other radio devices. To get the maximum amount of range, please refer to the “How the System Works” section of this guide.

How long can I continuously deliver static stimulation to my dog?

– The maximum amount of time you can press the Continuous Static Stimulation/Front Button and deliver static stimulation to your dog continuously is 10 seconds. After 10 seconds, the Remote  Transmitter will “time out” for 5 seconds. The Continuous StaticStimulation/Front Button must be released and pressed again.

What do I do if my dog’s neck becomes red and irritated?

– This condition is due to the Contact Points irritating the skin. Discontinue use of the Collar Receiver for a few days. If the condition persists beyond 48 hours, see your veterinarian. Once the skin returns to normal, resume use, and monitor the skin condition closely.

Can I attach a lead/leash to the GS-100?

– DO NOT attach a lead/leash to the GS-100. You may put a separate non- metallic collar on your dog’s neck and attach a lead/leash. Be sure the extra collar does not interfere with the Contact Points.

TROUBLESHOOTING

TROUBLESHOOTING

My dog is not responding when I press a button.| •       Check to see if the Collar Receiver has been turned on and the Indicator Light is flashing.
•       If your range has reduced from the first time you have used

it, please check to see if the battery is low in either the Remote Transmitter or Collar Receiver.
•       Many factors can impact the range you have with the GS-100. For a list of these factors, please refer to “How the System Works.”
•       You can verify the Collar Receiver is delivering static stimulation to your dog by placing the test light, enclosed in your kit, on the Collar Receiver. Please refer to the “Test Light Instructions” section for details.
•       Increase the intensity level. Refer to “Find the Best Intensity Level for Your Dog” for more information.
•       Make sure the Collar Receiver’s Contact Points are placed snugly against your dog’s skin. Refer to “Fit the Collar Receiver” for more information.
•       You may need to switch to the longer Contact Points included with your system or trim the hair beneath the Contact Points.
•       If you notice your operating time dropping to about half the original time, your Collar Receiver battery needs to be replaced. Contact the Customer Care Center to purchase a new one.

The Collar Receiver will not turn on.| •       Make sure the Collar Receiver has been charged. The Collar Receiver will charge in 2 hours.
The Collar Receiver is not responding to the Remote Transmitter.| • Make sure the Remote Transmitter has been charged. The
•       Remote Transmitter will charge in 2 hours.
•       Verify the Collar Receiver has been turned on and the Indicator
•       Light is flashing. Refer to “Turning the Collar Receiver On and Off.”
•       Refer to “Match the Collar Receiver and Remote Transmitter.”

TERMS OF USE AND LIMITATION OF LIABILITY

  1. TERMS OF USE: The use of this product is subject to your acceptance without modification of the terms, conditions, and notices contained in this product. Use of this product implies acceptance of all such terms, conditions, and notices. If you do not wish to accept these terms, conditions, and notices, please return the Product, unused, in its original packaging, and at your own cost and risk to the relevant Customer Care location together with proof of purchase for a full refund.
  2. PROPER USE: Proper Use includes, without limitation, reviewing the entire Operating Guide and any specific safety information statements. The specific temperament or size/weight of your dog may not be suitable for this product. If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or certified trainer prior to use. For products used with dogs where training is desired, Radio Systems Corporation recommends that these training products are not used if your dog is aggressive and accepts no liability for determining suitability in individual cases.
  3. NO UNLAWFUL OR PROHIBITED USE: This product is designed for use with dogs only. This product is not intended to harm, injure, or provoke. Using this product in a way that is not intended could result in a violation of Federal, State, or local laws.
  4. LIMITATION OF LIABILITY: In no event shall Radio Systems Corporation or any of its associated companies be liable for (i) any direct, indirect, punitive, incidental, special or consequential damage and/ or (ii) any loss or damages whatsoever arising out of or connected with the use or misuse of this product. The Purchaser assumes all risks and liability from the use of this product to the fullest extent permissible by law.
  5. MODIFICATION OF TERMS AND CONDITIONS: Radio Systems Corporation reserves the right to change the terms, conditions, and notices governing this product from time to time. If such changes have been notified to you prior to your use of this product, they shall be binding on you as if incorporated herein.

COMPLIANCE
FCC: US
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a specific
installation. If interference does occur to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna
  • Increase the separation between the equipment and the receiver
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
  • Contact Customer Care or an experienced radio/TV technician for assistance
    CAUTION: Modifications or changes to this equipment are not expressly approved by Radio Systems Corporation and may void the user’s authority to operate the equipment.

IC: CANADA
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

CUSTOMER CARE CENTER
USA & Canada – Tel: 1- 800-732-0144
sportdog.com/contact-us

BATTERY DISPOSAL

WARNING
See Important Safety Information on pages 2-3 related to the battery.

This system operates on two Li-Ion battery packs (160mAh capacity for the Collar Receiver and 200mAh capacity for the Remote Transmitter). Only replace a battery received by calling the Customer Care Center at 1-800-732-0144.
A separate collection of spent batteries is required in many regions; check the regulations in your area before discarding spent batteries. Please see below for instructions on how to remove the battery from the product for separate disposal.
AT THE END OF PRODUCT LIFE, USE THESE BATTERY REMOVAL INSTRUCTIONS FOR FINAL DISPOSAL (DO NOT OPEN THE COLLAR RECEIVER OR REMOTE TRANSMITTER UNTIL YOU HAVE RECEIVED THE REPLACEMENT):

  • Using the supplied (T8) Torx Driver for your Remote Transmitter and/or a 3/32 Allen wrench for your Collar Receiver, remove the case screws.
  • Remove the case back or cover.
  • Remove the old battery.

WARNING

  • When removing the old battery pack, care must be taken when gripping the connector firmly to avoid damaging the wires. Shorting the battery wires may cause fire or explosion.
  • These instructions are not valid for repair or battery replacement. Replacing the battery with a battery not specifically approved by Radio Systems Corporation may cause fire or explosion. Please call the Customer Care Center to avoid invalidating your warranty.

IMPORTANT RECYCLING ADVICE
Please respect the Waste Electrical and Electronic Equipment regulations in your country. This equipment must be recycled. At the end of the product’s life, do not place it in the normal municipal waste system. Please check the regulations in your area or return it to where it was purchased so that it can be placed in our recycling system. If these options are not possible, please contact the Customer Care Center for further information.

1-800-732-0144
Radio Systems Corporation
10427 PetSafe Way
Knoxville, TN 37932 USA
+1 800-732-0144
400-2580-17
©2022 Radio Systems Corporation

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals