NICROX S5 Electric Scooter User Manual
- June 5, 2024
- NICROX
Table of Contents
NICROX S5 Electric Scooter
Safety Instructions for Use
- This product is an electric scooter for adults, is limited to one person, and do not scooterry others at the same time. Minors must use it under the supervision of adults.
- Please wear safety helmets and other protective equipment when riding this product.
- Please do not ride this product in unsafe or illegal places such as motorways.
- Please practice in the open space first, and drive after skillfully controlling.
- Please do not do dangerous actions or ride with one hand while the scooter is driving. Keep your feet on the pedal.
- Do not turn off the power supply while the scooter is driving.
- Please do not try to directly pass through the steps with a gap of over 3cm, which may overturn the scooter and cause injury to the driver or damage to the scooter. Steps below 3cm should also be avoided as much as possible.
- In case of rough or uneven road conditions, please slow down or get off the bus to push.
- Users must adjust the height of the product to the appropriate position to ensure driving safety.
- Do not ride this product on slippery roads with oil or ice on the surface.
- Do not use this product in an environment below-5°C.
- Please do not immerse the product in a depth of more than 3cm of water and put it on hold to avoid damage to the electrical parts of the vehicle due to water inflow.
- Do not ride in bad weather such as rain, snow and strong winds, so as not to cause unnecessary injuries due to unnecessary factors.
- If you do not use this product for a long time, please charge it at least once within 30 days.The charging port must be kept clean and dry.
- Do not expose this product to the sun for a long time. At the same time, outdoor enclosure should be avoided.
- Please use the charger equipped with our company’s scooter. Do not use the charger indiscriminately to avoid safety problems.
- When charging, it is necessary to ensure that someone is on site to manage it.
- Please try to charge in an open place. When the charger temperature is too high, please stop charging.
- Please do not leave it in a severely humid place for a long time.
- Plastic bags are in danger of suffocating babies.
List of Main Components and Parameters of Products
Main Components(Ref.)
Parameter Table(Ref.)
Model
Battery
| ss
48V13Ah
| S6
48V18Ah
| S7
48V22Ah
| S8
48V26Ah
| SlO
60V18Ah
| S7-S
Dual drive
48V22Ah
| S8-S
Dual drive
48V26Ah
| SlO-S
Dual drive
60V18Ah
| Sll-S
Dual drive
60V22.4Ah(LG)
---|---|---|---|---|---|---|---|---|---
Range| 40-SSkm| 55-70km| 65-80km| 75-90km| 70-85km| 65-80km|
70-85km
| 70-85km| 80-lO0km
Max. Speed| S0km/h| S0km/h| S0km/h| S0km/h| 60km/h| SSkm/h| 55km/h| 65km/h|
65km/h
Motor|
600W
|
600W
|
600W
|
600W
|
1000W 600W*2
|
600W*2
|
lO00W*2
|
l000W*2
Frame Material| | | | |
Aluminium alloy
| | |
Brake| | | | | Front and rear brake| | |
Operation instruction
Fold and Expand
Riding operation
Button|
---|---
Oper ation
Long press for 3 seconds
| Function
l.ln the main interfacei enter the setting menu :
2.When setting the interface, retu rn to the main in ter face;
Short press
Long press for 3 seconds
[GE]
Sho11 press
Long press for 3 seconds
[B
Short press
t
Long press for 3 seconds
@
Short press
| Lln the main interface, turn on/ off the front whee l drive fu nction;
2.When se tting the inte rface, switch r he optio ns;
1. ln the majn interface1 increase the gear;
2. ln the pas:mrord interface, increase the value of the password;
l.I n the main interface, sta rt the push function (need 1-3 gears, release the key to cancel)
Lln the main inte rface, reduce the gear;
2.fn the password interface, reduce the value of the password;
l.At any inte rface,turn off the computer
Lin the off sta te1 power on;
2. In lhe main interface, turn on/ off the headlamp;
3. ln the password input interface of power oni switch the number
of password digits;
In the main interface,press thekey for 3S to enter the setting interface; When
into the setting interface, press the key for 3S to return to the main
interface; Short press key to switch setting options.
CD If the user enables the power on password function, the password input
interface will appear after the power on. In the password input
interface,press [GE] and [8] to set the value of the selected password bit,and
press @to switch the password bit to be set. The password input is
correct,press to enter the main interface, and the system can operate
normally; If the password is not entered correctly, re-enter it. The default
password of the instrument is 1111.
Note: if the user changes the password, please remember the changed
password. If you forget the password,long press and [8] key 2s to reset the
factory password.After entering the setting interface,short press key to
switch to P2: power on password On/ Off setting. You can use [GE] or [8] key
to switch back and forth to select on or off.
- After power on, the default is zero gear,for safety,please confirm that the first gear starts. The default setting of this product is non-zero start (after entering the setting interface, short press key to switch to PS: to turn the setting interface, use [GE] or [8] key to switch, On is zero start and Off is non zero start) you need to use your feet to help you slide and use your thumb to hook the acceleration handle at a constant speed before you can start riding.
- Enable cruise setting: after entering the setting interface, short press key to switch to P9: enable cruise setting interface, and use the [GE] or [8] key to select On or Off. After starting the cruise, press the handle for a certain time to lock the power speed. At this time, releasing the handle will not stop the power,but shifting gears will stop the power. All settings are finished.Long press the key again to return to the main interface of the instrument.
- If you encounter someone or obstacles in front of you during riding, please release the throttle first, and brake the left brake handle (rear brake) first and then brake the right brake handle (front brake) next to stop braking or deceleration.
How to charge
- Open the charging hole rotation protection sleeve and insert the charger output connector into the charging hole on the body.
- Plug the charger input plug into the supply socket (AC110V-220V).
- The charger indicator light is red, indicating that charging is taking place; when the charger indicator turns green, the battery is fully charged.
- When charging the battery, please place it in a dry and ventilated environment for use.
Product Maintenance
- Tire: This product tire uses rubber elastic tire. When the tire present obvious wear or rupture and needs to be replaced in time, please contact the dealer to replace the original tire. Every month, please check a scooter to see if there are any loose screws. If there are loose screws, please tighten them in time.
- Brake: This product adopts the braking mode of front disc brake and rear drum brake. Usually, more attention should be paid to check the thickness of brake friction plates. If there is serious wear, it should be replaced in time to prevent adverse consequences caused by braking.
- Battery: when you get the electric scooter for the first time, please charge the battery and use it.
If the vehicle is not used for a long time, it must be charged at least once a
month.
If the state power cannot be charged, please contact the after-sales service
as soon as possible.
The battery damaged due to other abnormal factors such as water inflow and
collision is not covered by the warranty.
If the intensity and frequency of use of the car is high, you need to check
the screws of the car once a month and replace the screws every
half a year to avoid bad conditions.
The lithium battery equipped by our company has a charging cycle of at least
500 times, which can generally reach more than 600 times in normal use. When
the battery is fully charged and the mileage is only half of the factory
mileage, it is recommended to replace the lithium battery.
After-sales maintenance
Please contact your local dealer for after-sales maintenance. During the warranty period, if the following reasons cause faults and damages, they are not within the warranty scope:
- Not properly maintained and repaired in accordance with this manual.
- The electric scooter is used for other purposes to perform dangerous actions such as special effects, resulting in damage or functional failure.
- Any self-disassembly or use of parts outside the original factory.
- Using the scooter body and scooter body accessories damaged by mistake, traffic accident or accidental collision.
- lncomplete labeling, water inflow and mismatched parts numbers.
- Driving on abnormal roads to use damage or functional failure.
- Business rental use or improper non-franchise use.
- Causes of force majeure.
- Exposing this product to the sun for a long time or rain for a long time, thus causing the rapid aging and functional failure of this product.
Licensor:
Zhejiang Lebu Electric Vehicle Co.,Ltd
Address:
Building l,Xinyada International Creative Center, Hangzhou,Zhejiang,China
Manufacturer:
JinhuaJoyor Vehicle Co.,Ltd
Address:
N0.379,Lantian West Road,Chengxi New District,Yongkang
Tel:
+86-0571-81915113
Email:
[email protected]
Website:
www.joyorglobal.com
[email protected]