NICROX H60 Electric Scooter User Manual

: July 8, 2024
: NICROX

Table of Contents

NICROX H60 Electric Scooter
Part One : Function introduction
Part Two : Scooter assembly
Part Three : Learn to ride
Part Four: Safety instructions
Part Five· Scooter Maintenance
Part Seven · Warranty Policy
Declaration
Read User Manual Online (PDF format)
Download This Manual (PDF format)

NICROX H60 Electric Scooter

Specifications

Dimensions: 11084911152 mm
Folded Dimensions: 1108491414 mm
Handlebar Height: 850mm
Motor: 250W rear drive
Battery: 36V10Ah
Max Speed: 20 km/h
Speed Modes: 10/15/20 km/h
Operating Temperature: 10°C-15°C-40°C
Storage Temperature: -20°C-50°C
Traversable Terrain: Asphalt/flat pavement, obstacles up to 0.39”, gap up to 1.81”
Battery Charging Temperature: 0°C-40°C
Battery Management System: Over-heat, short-circuit, over-current, and overcharge protection
Range: 35-40 km
Brakes: Front drum brake + Rear disc brake
IP Rating: IP X4

Braking
Use the brake lever on the handlebar to engage the brakes. Apply gentle pressure to slow down or stop the scooter.

Frequently Asked Questions (FAQ)
What should I do if my scooter malfunctions?
If you experience any issues with your scooter, refer to the Electric Scooter Performance Failure Table in the user manual for troubleshooting steps. If the problem persists, contact customer support for assistance.

Part One : Function introduction

Scooter Schematic Diagram
Grip
Thumb power throttle
Dashboard
Front headlight
Front Reflector
Left brake lever
Folding stem
Folding Safety lock
Folding Safety lever
Aluminum label
Front mud guard
Driven wheel
Drum brake
Kick stand
Foot pad
Hook buckle
Rear fender
License plate holder
Disc brake device
Motor wheel
Dashboard schematic diagram
Speed display
Speed unit display(KM/h) (MPH)
Single trip mileage display/totalmileage display
Gear display
Headlight display
Fault display
Trip/Range
Battery Power display
Gear switch / mileage switch button
Light/ Power
Key function introduction
Long press the power switch button to tum on, long press again to tum off.
Short press the power switch button to tum on/off the headlights.
Short press the gear button to switch 1,2,3 gear.
Long press the gear button to switch single trip mileage and total mileage.

Part Two : Scooter assembly

Front tube assembly

Aller laking the whole 8COOIBr out of the packing box, placed it on a flat ground. Open kick stand 1 Connect the waterproof cable of the front lube and folding stem
Then insert the front lube into the f01ding stem2 , Then right the 818m and lock the folding wrench 3
Hearing 4 ‘click’ means the stem ia locked in place.

Fasten the front tube and the folding stem with the hex wrench and screws.
Note: First insert the four screws in sequence from hole to hole and finally tighten them together.

Power on testing

Perform testing after installation

Power on inspection
Gear shift inspection
Front headlight inspection
Braking force inspection
Fasten the front tube and the folding stem with the hex wrench and screws.

Note: First insert the four screws in sequence from hole to hole and finally tighten them together

Part Three : Learn to ride

Note : Beginners learning electric scooters are at risk of falling and injury.
Please wear helmets and protective gear at all times

Riding operation method
The scooter need a kicking-off starting. When power is on, one foot stands on the pedals and the other foot kicks back on the ground. 2 : When the scooter is sliding, then the other foot back on the pedals.|
When the scooter is stable, then push the right power throttle 1. Hold left hand on the brake lever lightly when braking. 2 Front-wheel drum brake and rear electronic brake is in effect simultaneously.
How to charge
Notice :
When the scooter battery power is used out, charge ii in lime to avoid damage to the battery.
When charging is complete, you need to unplug the charging port in lime, do not charge the battery for a long time. The charging port is located at position “1” on the front right side of the scooter. When charging, firstly open the dust-proof cap, and then insert the charging port. When the indicator light is red, it means charging is in progress. When turns green, charging is complete. Finally unplug the charging port and fasten the dust-proof cap.
Folding and carry

When folding, turn off the power, first lift up the safety lock, then open thesafety lever, then fold the folding stem to the rear part of the scooter. Lift the hook buckles on the rear mud guard, and finally buckle the 2 hooks together to complete the folding.
After folding, you can take the scooter to bus, metro and car trunk.

Part Four: Safety instructions

Prohibited items
When the scooter is turned on and needs to be moved, please do not press the thumb power throttle.
Do not hang backpacks or other forms of objects on the handlebars when riding the scooter.
Do not drive the scooter in the rain.
Do not press power throttle to accelerate when going downhill.
Do not drive at high speed o bumpy roads.
Do not ride toward steps which more than 2cm at high speed.
Dangerous operation
During riding, you need to hold the handlebars with both hands, do not drive with one hand.
During riding, please do not lift one foot or do other dangerous actions.
Do not drive in water with a depth of more than 2cm.
During high-speed driving, do not swing the scooter body or turn the handlebar a lot.
Do not step on or stand on the rear mud guard during riding.

Part Five· Scooter Maintenance

Brake debug
When the scooter has been driving for a period of time and the brake is too loose, you can tum the adjusting nut (position 1) on the drum brake to the proper position in counterclockwise direction. On the contrary, if you feel the brake is too tight, you can tum the adjusting nut by hand in clockwise direction.
Front tube debugging
When you feel the front tube of the scooter is shaking, please use a 2.SMM hex socket tool to tighten counterclockwise the four screws at the joint between the front tube and the stem (position 1). Tighten counterclockwise the two screws of the stem base with a SMM hexagon socket. (position 2)
Folding stem shaking debugging
When riding for a period of time and feel that the gap between the folding stem is too large, we can use tools to adjust the folding mechanism on the folding base. 1: Use a 2.5mm hex socket tool to unscrew the set screw in clockwise direction (position 1) 2: Use a 3mm hex socket tool to tighten counterclockwise the folding mechanism screw to the proper position (position

Use a 2.5mm hex socket tool to tighten the set screw (position 3).

Part Six : Scooter parameter sheet

Part Seven · Warranty Policy

Warranty content
Non-warranty regulations
Unauthorized maintenance, misuse, collision, negligence, abuse, liquid ingress, accident, alteration, incorrect use of accessories other than this product, or tearing, altering, or anti-counterfeiting labels;
The validity period of warranty has expired.
Damage caused by force majeure;
Conditions that do not meet the performance failures listed in the following “Electric Scooter Performance Failure Table”
Failure to use, maintain and adjust as required in the “User Manual” results in the performance failures listed in the following “Electric Scooter Performance Failure Table” for the scooter and its accessories
Damage caused by man-made reasons (including but not limited to scooter ﬂuid, punctured tires, impact, marks and damage caused by normal use of exterior parts, etc.);
Failure and damage caused by abnormal use of this product, (including but not limited to overload, riding down from steps, falling, extreme sports, etc.)
If this product is used for commercial purposes, it will not be guaranteed.
Electric scooter performance failure table

Declaration

The electric scooter is a sport and entertainment tool, not a transportation vehicle. However once you drive it into a public area, it will also have the property of a transportation vehicle, and you need to learn to master riding skills. WEshall not be liable for any casualties or losses caused by drivers’ inexperience or failure to follow the instructions in this user manual.
Please respect the pedestrian’s rights of way when driving. To avoid frightening pedestrians, you need remind pedestrians and slow down when passing behind them, stay alert during driving, drive at low and medium speeds on unconventional complex roads such as potholes and smooth surfaces, and maintain a reasonable and safe distance from others and vehicles.
When driving in countries and regions where there are no relevant national standards and regulations for electric scooters, you must strictly abide by the safety requirements of this manual for riders. WEwill not bear any direct and joint liabilities for all ﬁnancial, personal losses, accidents, legal disputes, and all other unfavorable events that cause conﬂicts of interest caused by the use behaviors that violate the instructions in this manual.
Please do not lend the electric scooter to people who can’t operate it. When you lead the electric scooter to a friend, you need to teach to use until he or she learn the basic operation. He or she must wear safety protective gear before using it.
Please perform a basic inspection of the electric scooter before each driving. If you ﬁnd any abnormalities such as obvious loose parts, signiﬁcantly reduced battery life, slow tire leaks or excessive wear, abnormal steering noise or malfunction, please stop using it immediately and cut it off. Do not drive forcibly. And please contact the after-sales service phone to obtain professional guidance or repair and maintenance services.
Do not use alcohol, gasoline, kerosene or other corrosive chemical solvents to clean the electric scooter, and it is forbidden to use a pressure gun to spray and wash, otherwise it may get an electric shock or cause serious failure due to internal water.
Do not use other types or brands of battery packs, do not touch the battery contacts, and do not disassemble or puncture the shell. Avoid metal objects contacting the battery contacts and causing short circuits. Otherwise, it may result in battery damage or personal injury.Only use the original charger to charge, otherwise there is a danger of damage or ﬁre.
Do not place the electric scooter or its battery pack in a car exposed to the sun in summer, and it is forbidden to put the battery pack into a ﬁre, otherwise it may cause the battery to fail, overheat, and even cause a risk of ﬁre. When don’t use scooter for more than 30 days, please fully charge it ﬁrst, store in a cool and dry place, and fully charge it every 60 days, otherwise the battery may be damaged and this damage is not covered by the warranty.
Only use the parts and accessories approved by US,Please do not modify your electric scooter without authorization. Damage to the electric scooter caused by unauthorized modiﬁcation is not covered by the warranty. WEwill not bear any responsibility for property losses, personal injuries, accidents, etc. caused by unauthorized modiﬁcation.

WARNING-Risk of ﬁre-No user Serviceable Parts