PROSCAN PSB3200 32 Inch Bluetooth Soundbar User Manual

PROSCAN PSB3200 32 Inch Bluetooth Soundbar

CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER SERVICEABLE PART INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

DANGEROUS VOLTAGE: The lighting flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

ATTENTION: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

WARNING: USE UNDER SUPERVISION OF AN ADULT DUE TO LONG CORD This unit has a long cord that can be easily tripped on or pulled on, causing injury. Please make sure it is arranged so that it will not drape over a tabletop, etc. Where it can be pulled on by children or tripped over accidentally.

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC WARNING:
To assure continued operation, follow the attached installation instructions and use only shield cables when connecting to other devices. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Important Safety Instructions

Before using the unit, be sure to read all operating instructions carefully, please note that these are general precautions and may not pertain to your unit. For example, this unit may not have the capability to be connected to an outdoor antenna.

1. Read these instructions
   All the safety and operating instructions should be read before the appliance is operated.

2. Keep these instructions
   The safety and operating instructions should be kept for future reference.

3. Heed all warnings
   All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow all instructions
   All operation and use instructions should be followed.

5. Do not use this apparatus near water
   The appliance should not be used near water; for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

6. Clean only with dry cloth
   The appliance should be cleaned only as recommended by the manufacturer.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
   Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or similar surface. This product should never be placed near or over a radiator or heat source. This product should not be placed in a built-in installation, such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Product the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
    An appliance and cart combination should be moved with care. Quick stop, excessive force and uneven surfaces may cause the appliance and cart combination to overturn.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.
    To protect your product from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Power source
    This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or another source, refer to the operating instructions.

16. Power lines
    An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Overloading
    Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

18. Object and liquid entry
    Never push objects of any kind into the product through openings as they may touch dangerous voltage points or short-out parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product.

19. Outdoor antenna grounding
    If an outside antenna is connected to the product, be sure the antenna system is grounded so as to provide some protection against voltage surges and built- up static charges. Section 810 of the National Electric Code ANSI/ NFPA 70 provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge product, size of grounding conductors, location of antenna- discharge product, connection to grounding electrodes and requirements for the grounding electrodes.

20. Service
    Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

21. Replacement parts
    When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original parts. Unauthorized substitutions may result in fire or electric shock or other hazards.

22. Safety check
    Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23. Wall or ceiling mounting
    The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

24. Damage requiring service
    Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions.

    • a) When the power- supply cord or plug is damaged.
    • b) If liquid has been spilled or objects have fallen into the product.
    • c) If the product has been exposed to rain or water.
    • d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an adjustment of other controls may result in damage and will require extensive work by a qualified technician to restore the product to its normal operation.
    • e) If the product has been dropped or the cabinet has been damaged.
    • f ) When the product exhibits a distinct change in performance- this indicates a need for service.

25. Note to CATV system installer
    This reminder is provided to call the CATV system installer’s attention to Article 820- 40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

NOTE: Refer all servicing to qualified service personnel. Servicing is required when the unit has been damaged in any way such as the following: the power-supply cord or plug has been damaged, liquid has been spilled into unit, the unit has been exposed to rain or moisture, the unit has been dropped or the unit does not operate normally.

PLACEMENT AND MOUNTING

Placing the Device on Table
When placing the Sound Bar on an entertainment center, bookshelf, or any type of enclosed space, be sure to allow at least 2-3 inches of space around the Sound Bar for ventilation. If the Sound Bar is enclosed in a tight space, without ventilation, heat generated from the Sound Bar could produce a potential heat hazard.

Mounting to a Wall

Mounting to a wooden wall

• A. Mark the position of the mounting screws on the wall using a pencil.
• B. Drill the screws directly into the marks that you have made on the wall and leave approx. 0.3 inches length to hook the sound bar.
• C. Put the sound bar onto the mounting screws. Make sure they are firm and stable.

Mounting to a brick wall

• A. Mark the position of the mounting screws on the wall using a pencil.
• B. Drill 2 holes on wall with a powerful electric drill.
• C. Insert the fixing plug and hammer into the holes.
• D. Secure the screws into the fixing plug and leave approx. 0.3 inches length to hook the soundbar.
• E. Put the sound bar onto the mounting screws. Make sure they are firm and stable.

LOCATION OF CONTROLS

Front View

Rear View

Top View

Remote Control

1. STANDBY button
2. Audio source buttons (Bluetooth, AUX, Line in, USB)
3. VOL – (Volume down) button
4. VOL + (Volume up) button
5. (Mute) button
6. (Play/Pause) button
7. (Previous) button
8. (Next) button
9. REC. (record) button

Note: Dotted line is for illustration.

BATTERY INSTALLATION OF REMOTE CONTROL

First Time Use

• Remove and discard the insulation film as figure on the right.
• Replacing Batteries For Remote Control
  1. Push and slide out the battery holder as figure 1 below.
  2. Replace the battery with a new CR2025 button cell as the polarity markings on the rear of the Remote Control.
  3. Close the battery holder.

Battery Precautions

Follow these precautions when using a battery in this device:

1. Use only the size and type of battery specified.

2. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment, a reserved battery may cause damage to the device.

3. Do not mix different types of batteries together ( e.g.: Alkaline and Carbon-zinc )
   or old batteries with fresh ones.

4. If the batteries in the device are consumed or the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible leakage.

5. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture.
   ( Follow battery manufacturer’s instructions.)

6. The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

7. Clean the battery contacts and also those of the device prior to battery installation.

8. The remote control supplied with a coin/button cell battery. If the coin button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used battery away from children. If the Battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed any part of the body, seek immediate medical attention.

Caution:

• Danger of explosion if the battery is incorrectly replaced.
• Replace only with the same or equivalent type.

Remote control operation range

• When there is an obstacle between the transmitter and the unit, the unit may not operate.
• When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the REMOTE SENSOR of the unit, the operation of the remote may be unstable.

GENERAL OPERATION

1. Connect the AC/DC adapter to the unit and wall outlet. The red indicator will light and the unit is in standby mode.

2. Press and hold the Standby/Source button on the unit or press the button on remote control to turn on the unit. Repeat the operation, and the unit will turn to STANDBY mode, the indicator turning to Red.

3. Press the Standby/Source button on the unit repeatedly, or press BT (bluetooth) button, AUX button, LINE (in) button or USB button to switch to desired mode. The color of indicator will turn to :

   • Blue………………………………………………………………….Bluetooth Mode
   • Violet……………………………………………………………………….AUX Mode
   • Green……………………………………………………………………Line in Mode
   • Cyan………………………………………………………………………..USB Mode

4. During Playback: Press the VOL ( Volume ) + or – buttons on the unit or Remote Control to adjust volume level as desired.
   Press the (Mute) button on the Remote Control to turn off the sound. Press again to resume.

5. When finishing listening, press and hold the Standby/Source button on the unit or press the STANDBY button on remote control to put the unit in standby mode.

Note: When a USB device is insterted into the USB port, the current playback in BT, AUX or Line in mode will be interrupted, and the unit will switch to USB mode and audio track stored in USB deive starts to play automatically

BLUETOOTH PAIRING AND CONNECTION

For first time use or re-pairing, pair the unit to an external Bluetooth (BT) device as follows:

1. Power ON the unit as previously explained.

2. Press the Standby/Source button on the unit repeatedly, or press the BT button directly on remote control to switch to the Bluetooth mode. The indicator will turn to Blue and blink.

3. Power ON the external BT Device and select Bluetooth to enter into search mode. when “Pro PSB3200” appears, click it to start pairing. After paired, the indicator will stop blinking and a beep will be heard.
   (For details on pairing procedures, please refer to the user’s manual of your BT Device.)

4. During playing:

5. Press the button to skip tracks.

6. Press the button to pause. Press again to resume normal playback.

LISTEN THROUGH AUX IN

An external (Auxiliary) audio source (i.e., personal CD player or MP3 player) can be connected to this unit and heard through the speakers.

1. Plug one end of the Aux cable into the AUX IN jack on the rear of the unit.
2. Plug the otehr end of the Aux In cable into the AUX OUT or earphone jack of the external audio source.
3. Power on the unit as previously explained.
4. Press the Standby/Source button on the unit repeatedly, or press the AUX button directly on remote control to switch to the AUX mode. The indicator will turn to Violet.
5. Power on the connected external player and start playing as usual.

LISTEN THROUGH-LINE IN

An external Video/Audio player (such as TV, DVD player, VCR, etc.) can be connected to this unit and heard through the speakers.

1. Plug one end of RCA White and Red cable into the LINE IN jacks on the rear of the unit.

2. Plug the other end of RCA White and Red cable into audio out jacks of TV or external device as the illustration shown as below.
   NOTE: Make sure to connect to AUDIO OUT. If you connect it into AUDIO IN of external device, you will not hear the sound.

3. Power on the unit as previously explained.

4. Press the Standby/Source button on the unit repeatedly, or press the LINE button directly on remote control to switch to the Line in mode. The indicator will turn to Green.

5. Power on the connected external player and start playing as usual.

LISTEN THROUGH USB DEVICE

1. Insert the USB device to the USB Player port on the unit.
2. Power on the unit and enter the USB mode as previously explained.
3. Press the Standby/Source button on the unit repeatedly, or press the USB button directly on remote to switch to the USB mode. The indicator will turn to Cyan. Press the button or the button on the remote to play next or the previous track.

RECORDING OPERATION

To Record Audio Track:

1. Insert the USB device into the USB port on the unit.
2. Start to play in BT, AUX or Line in mode as indicated above.
3. To start recording, press REC. button on the remote (or press and hold Vol+/REC. button on the unit). Two beeps will be heard, indicating the recording process starts.
4. To stop recording, press REC. button on the remote (or press and hold Vol+/REC. button on the unit) again. A beep will be heard, indicating the recording process ends.

To Play the Recorded Track:

1. Insert the USB device including recorded files to the USB port on the unit.
2. Press the Standby/Source button on the unit repeatedly or press USB button on the remote to enter USB mode.
3. It will start to play automatically. Press the button on the remote to play recorded or existed tracks.

TROUBLESHOOTING GUIDE

not connected

| Connect the power AC/DC adapter to the unit or wall outlet.

The unit is in standby mode

| ****

Press and hold Standby/Source button

on the unit or press  button on remote control to turn on the unit from Standby mode.

No sound

| ****

Volume in minimum position

| ****

Raise volume by pressing the

VOL (Volume) + button.

The paired/connected device is not in

playing mode

| Play music/movie in the paired/ connected device as usual and make sure the volume level of it is in high

level.

Input source wrongly selected

| Press the Standby/Source button

on the unit or SOURCE button on the Remote Control repeatedly to set the input source to the desired mode.

Sound distortion| Volume level too high| Reduce the volume level by pressing the VOL (Volume ) – button.

Reduce the volume level of the paired/connected device.

Remote control not working

| ****

The battery is weak

| ****

Replace with new battery

Bluetooth reception failure

| ****

The external device is too far from the unit

| ****

Put the external BT device close to the unit.

Have not paired

| ****

Pair the unit with the BT Device as the procedures stated in this manual.

GENERAL SPECIFICATIONS

• Power Source…………………………………………………DC9V 1300mA
• Audio Power…………………………………………………………………………………5W x 2
• Bluetooth Effective Range in Open Area…………………………………..Up to 32 feet
• Remote Effective Range…………………………………………………………Up to 16 feet

ACCESSORIES

• 1 x AC/DC Adapter
• 1 x Remote Control
• 1 x AUX Cable
• 1 x LINE IN Cable
• 1 x User’s Manual

SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE

For service assistance and product information, please call: 1-800-968-9853. Curtis International Ltd.
7045 BECKETT DRIVE, UNIT 15, MISSISSAUGA, ON, L5S 2A3 www.curtisint.com

To make a warranty claim, please email support@curtiscs.com or call 1-800- 968-9853.

90 Day Warranty

This product is warranted to be free from defects in material and workmanship for a period of ninety (90) days from the date of original purchase. During this period, your exclusive remedy is repair or replacement of this product or component found to be defective, at our option; however, you are responsible for all costs associated with returning the product to us. If the product or component is no longer available, we will replace with a similar one of equal or greater value. Prior to a replacement being sent, the product must be rendered inoperable or returned to us.

This warranty does not cover glass, filters, wear from normal use, use not in conformity with the printed directions., or damage to the product resulting from accident, alteration, abuse, or misuse. This warranty extends only to the original consumer purchaser or gift recipient. Keep the original sales receipt, as proof of purchase is required to make a warranty claim. This warranty is void if the product is used for other than single-family household use or subjected to any voltage and waveform other than as on the specified rating on the label (e.g., 120V~60Hz).
We exclude all claims for special, incidental, and consequential damages caused by breach of express or implied warranty. All liability is limited to the amount of the purchase price. Every implied warranty, including any statutory warranty or condition of merchantability or fitness for a particular purpose, is disclaimed except to the extent prohibited by law, in which case such warranty or condition is limited to the duration of this written warranty. This warranty gives you specific legal rights. You may have other legal rights that vary depending on where you live. Some states or provinces do not allow limitations on implied warranties or special, incidental, or consequential damages, so the foregoing limitations may not apply to you.
For faster service, locate the model, type, and serial numbers on your appliance.

ATTACH YOUR PROOF OF PURCHASE HERE, PROOF OF PURCHASE IS REQUIRED TO OBTAIN WARRANTY SERVICE.
Please have the following information available when you contact the Support Team:

• Name, address and telephone number.
• Model number and serial number.
• A clear, detailed description of the problem.
• Proof of purchase including dealer or retailer name, address and date of purchase.

References

• Curtis International - Affordable TVs, electronics and appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>