tp-link AP115-Wall 300Mbps Wireless N Wall Plate Access Point Instructions

Regulatory Compliance
AP115-Wall 300Mbps Wireless N Wall Plate Access
Point Instructions

For Class B EAP with no adapter:

FCC Compliance Information Statement

Product Name: Omada EAP
Model Number: EAP115-Wall / EAP225-Wall / EAP230-Wall / EAP235-Wall / EAP615-Wall / EAP655-Wall
Responsible party:
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tplink.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
   Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”
We, TP-Link USA Corporation, have determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made to the equipment and the equipment is properly maintained and operated.
Issue Date: 2022-09-28
CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Frequency band: 5150 – 5250 MHz:
Indoor use: Inside buildings only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 – 5250 MHz band.
Frequency band: 5250 – 5350 MHz:
Indoor use: Inside buildings only. Installations and use in road vehicles, trains, and aircraft are not permitted. Outdoor use is not permitted.
Frequency band: 5470 – 5725 MHz:
Installations and use in road vehicles, trains, and aircraft and use for unmanned aircraft systems (UAS) are not permitted.

OPERATING FREQUENCY (the maximum transmitted power)

For EAP115-Wall:
2412MHz—2472MHz(20dBm)
For EAP225-Wall / EAP230-Wall / EAP235-Wall / EAP615-Wall:
2412MHz—2472MHz(20dBm)
5150MHz—5250MHz(23dBm)
For EAP650-Wall / EAP655-Wall:
2412MHz—2472MHz(20dBm)
5150MHz—5250MHz(23dBm)
5250 MHz -5350 MHz (23dBm)
5470 MHz -5725 MHz (30dBm)
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU, and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp- link.com/en/ce.
RF Exposure Information
This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
The device complies with RF specifications when the device is used at 20 cm from your body.
National Restrictions
For EAP225-Wall / EAP230-Wall / EAP235-Wall / EAP615-Wall / EAP650-Wall / EAP655-Wall:
Attention: This device may only be used indoors in all EU member states, EFTA countries and Northern Ireland. UKCA Mark

UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK Declaration of Conformity may be found at https://www.tp- link.com/support/ukca
National Restrictions
Attention: This device may only be used indoors in Great Britain.

Canadian Compliance Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1.  This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Caution
For EAP225-Wall / EAP230-Wall / EAP235-Wall / EAP615-Wall / EAP650-Wall / EAP655-Wall:

1. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong.
2. For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 54705600MHz, and 5650-5725MHz.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)

Safety Information

• Keep the device away from water, fire, humidity, or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Do not use devices where wireless devices are not allowed.
• Operating Temperature: 0℃~ 40℃(32℉~ 104℉)
  Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to the proper use of the device. Please use this product with care and operate at your own risk.

Explanation of the symbols on the product label
Note: The product label can be found at the bottom of the product and its I.T.E. power supply.

Mounting Requirements

For safety, we recommend you use the original screws in the package when mounting. The following are alternatives to mounting the device on the wall:

• (For EAP115-Wall / EAP230-Wall) Use a 86 mm/standard EU wall junction box and 2 screws that comply with ANSI B1.1 4# or 6# standard and are longer than 15 mm.
• (For EAP225-Wall / EAP235-Wall) Use a 86 mm/standard EU/standard US wall junction box and 2–4 screws which comply with ANSI B1.1 4#, 6#, or 8# standard and are longer than 8.5 mm.
• (For EAP615-Wall / EAP650-Wall / EAP655-Wall) Use a 86 mm/standard EU/standard US wall junction box and 2–4 screws which comply with ANSI B1.1 4#, 6#, or 8# standard and are longer than 10 mm.

References

• Link: Simple, secure one-click payments
• CE Regulatory Compliance | TP-Link
• Regulatory Compliance | TP-Link
• WiFi Networking Equipment for Home & Business | TP-Link

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>