COSTWAY EP23758 1500W 12H Timer Remote Control Electric Space Heater User Manual

COSTWAY EP23758 1500W 12H Timer Remote Control Electric Space Heater User Manual

PACKAGE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble pirate, or install the product.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: POTENTIAL ELECTRICAL HAZARD IF NOT ADHERED TO. When using electrical appliances, basic precautions should always be followed to reduce the Risk of fire, electric shock, and injury to persons, including the following:

• This heat must be plugged into a 120 V, 15 amp (of its own. Do not plug anything else into the same circuit. If unsure if your home meets this specification, consult a certified electrician Prieto use. Risk of fire, overheating, malfunction, propel damage, injury, or even death may result if not adhered to!
• Connect to a properly grounded, 3-prong outlet only. Do not connect the heater to extension cords, Sue protectors, timers, direct bakers an outlet with other appliances connected to the same outlet. Risk of fire, overheating, malfunction, property damage urn, or en death may result if not adhen1d to
• This heated is hot when in use. To avoid but s, do not let bare skin touch hot surfaces. Use handles (ce taint models wheels to move this heated.
• Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 ft. (0.9 ml from the front of the heated and keep them away from the sides and rear of the heater.
• Extreme caution is necessary γwhen any heated is used by one children, invalids, pets, o when the heated is left operating unattended.
• Always unplug the heater when not in use.
• Do not operate any heater with a damaged cord or plug o after the heater malfunctions, has been dropped damaged in any manner. Contact the manufacturer for resolution options.
• Do don’t use outdoors. Expo SU udo elements such as rain, snow, sun, wind or extreme temperatures may cause the hector become a safety hazard.
• This heater is not intended for use in bathrooms, laundry areas, and similar into locations, nor any locations that use GFCI outlets.
• Never place the heater where it may fall into a bathtub or other water recaptures.
• Do not run the cord under Capet. Do not cover the cord with throw rugs, runners, or similar coverings. Anagen the cd away from traffic areas and where it will not be tripped over.
• The heated must be plugged into a wall outlet that is a dedicated circuit with a minimum 15 amp rating on that individual ci-cult.
• To disconnect the heater, fist turn the power button to the OFF position and then move the plug from the wall outlet.
• Do not allow foreign objects to enter or block any ventilation exhaust opening as this may cause eclectic shock, fire, or damage the heater.
• Allow at Least 3 ft. of unobstructed space to the front and rear of the heater to allow for maximum heat, air, and ventilation flow.
• A heater has hot and arcing sparking parts inside. Do not use it in areas when gasoline, paint flammable liquids are used o stored, nor use flammable solvents to clean the heater. Keep the heater dry at all times.
• Use this heater only as described in this manual. Any theses not recommended by the manufacture may cause fire, eclectic shock yurt persons.
• Do not use abrasive solvents to clean the heater as it may cause damage to the finish or casing.
• To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft Sly faces, like a bed, where opening may become blocked.
• Always plug heaters directly into a wall outlet/receptacle. Neve use with an extension co relocatable power tap (outlet/power stipe).

SAVE THESE INSTRUCTIONS

Child Lock Safety Feature

Press and hold the child lock button located on the control panel for 5 seconds or remote control for 3 seconds. Locking is confirmed when a buzzer rings and the control panel displays “”CL’.’. When locked, the control panel and remote control (if provided] will not function.

To unlock the control panel or remote (if provided], repeat this procedure. Unlocking is confirmed when a buzzer rings and the lock indication disappears.

Tip-Over Safety Feature
This heater is equipped with a tip-over safety feature. Once the heater is tipped over, an internal switch will automatically shut the heater off. Once the heater is restored to an upright position, the heater will reset. To continue operation, turn on the heater using the control panel or supplied remote control (if provided] on the heater.

Overheat Safety Feature
This heater is equipped with an overheat safety feature. When the internal components of the heater reach a certain temperature that could cause overheating or possible fire, the heater will automatically shut off.

WARNING: This heater has a voltage rating of 120 volts. The cord has a three-blade, grounding-type plug. An adapter is available for connecting three-blade grounding-type plugs to two-slot receptacles. The grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

DO NOT DEFEAT THE SAFETY PURPOSE OF THE GROUNDED PLUG.

WARNING: It is normal for the power cord to feel warm to the touch. However, a loose fit between the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a different outlet. Contact a qualified electrician to inspect the original outlet for damage.

Specifications

FREQUENTLY ASKED QUESTIONS

Please review these frequently asked questions on the next few pages prier to using your heater.

Q. My heater emits a strange odor when I first open the box and when I turn the hr on for the first time. Why is this happening?

A. This is normal. This heater is treated with a special heat safe/resistant coating. This odor will sometimes be resent when the box is opened. When the coating is exposed to heat, it produces this piacular deducing the fist few hour of operation. This will dissipate after the break- in period. lf you are sensitive to odor you may want to pre-burn the unit in a garage with the do open until the initial odor dissipates.

Q. If my heater runs on its max wattage setting, how many BTUs is that?

A. This heater is intended to be used as supplemental heat in a as most needed. It may take several minutes to several hurls theta you area, depending on minus fact the below chart provides BTU translations for different wattages.

Q. Can the heating elements be replaced?
A. Replacement heating elements can be obtained from the manufacturer. All parts may be purchased through the manufacture if your product is out of warranty. If you feel that the elements are definitely faulty right out of the box, contact Customer Support. A representative can then direct you to the next step.

Q. Once I plug the unit in and turn it an, how long will it take to heat my room?
A. The heating process in the heater begins immediately upon power ing  on and setting the desmid temperature above the ambient temperature. A noticeable change in the ambient temperature of the room will vary due to variables such as the location of the heater (in the home). floorplan and size of the room, how well the room is insulated, how many doors endows, how much bare concrete (acts as a heat sink with any type of heating), the opening and closing of an extend  door, long hallways, high ceilings, etc. Customers with smaller rooms experience quick heat changes. Rooms with lacer and open floor plans can expect up to 24 hours completely heat up.

Q. I do not have a grounded outlet. can I use adapters, a 2-prong power strip, remove the ground prong from the cord?
A . NO! If you do not have a grounded outlet, contact a certified electrician for advice. Removing altering any pat of the heater’s Original design ointment (including the power cord) will void the warranty and make you liable for any unexpected hazardous exults.

Q. My Heater has an ECO setting? How does this setting work?
A. The ECO mode on your heater is a program that attempts to keep the temperature strictly at a “warm” 68° F (20°C). This also helps with efficiency, as it is programmed to 1) Increase the power to the unit’s maximum wattage if the temperature drops below 64.4。F (18°C) 21 Gradually reduce the wattage used as it approaches 66.2 19。Cl F and 3) Stop heating when 68° F (2Cl is achieved. This is considered an Economical function, since in the ECO setting, the heater is almost neve running at the maximum watts.

Q. The temperature on my heater does not match the temperature display on my wall, or external thermostat. Why?
A. This is completely normal. The temperature display on your heater may vary from the temperature display on another thermostat (like the one mounted to your wall or a purchased external thermostat]. This is because the temperature sensor on the heater reads the temperature directly around the heater.
With the heater near the cold floor land heat rising). any readings on elevated or external thermostats will differ in readings on the heater. The best way to operate your heater is to set the unit on High and dial up to a temperature that feels comfortable to you. Then, leave it at that temperature, regardless of the mismatch. The heater will cycle off when the set temperature is met or exceeded slightly.

Q. Can I use more than one heater at a time? Can I use the heater and another appliance at the same time?
A. Yes, but make sure they are not plugged into the same circuit. Each heater requires its own minimum 15-amp circuit with no other items plugged into that circuit or outlet. This is because heaters are considered appliances and draw out high amperage. If you are unsure your circuit meets these requirements, verify with a certified electrician.

WARNING: Risk of fire, damage to property, or injury may result if requirements are not met.

Q. Why does my heater’s fan continue to run after the set temperature is reached or the power is turned off?
A. This is normal. The heater’s fan will continue to run even after the heater automatically cycles down. The fan continues to run so that every last bit of heat is blown out of the heat chamber while allowing the unit to continue filtering your air. Once the internal box/components cool completely, the fan should then shut off on its own. In this case, allow a few minutes after the heat cycles off (with power on]. The fan will shut off faster when the power is turned off.

Q. My heater’s display shows my ambient temperature to be in the 20s when I know it is warmer than that. Why?
A. The heater’s display is defaulted to read the temperature as Fahrenheit. If your heater is definitely heating but shows it is in the 20s you probably have the setting to read your temperature in Celsius rather than Fahrenheit.

Q. My heater’s power cord gets warm. My cord is showing signs of heat or melting at the outlet. Is this normal?
A. A warm power cord is normal. These power cords are rated safe for up to 105°C/ 221 °F by the UL, CSA, or ETL. The exception is, if you detect heat, smoke, or signs of melting at the contact point of the wall outlet, it may be due to loose or worn wall contacts (or arcing]. Please stop using the heater immediately, contact warranty support for a replacement power cord, and have a certified electrician replace the wall outlet as soon as possible.

Q. What kind of water should I use to fill my humidifier?
A: Use only potable (drinkable] water. Distilled or de-mineralized water is best as it has less mineral content than regular tap water. When used, these water types make your humidifier less likely to expel white mineral dust into your indoor air – and less likely for that dust to invade your lungs. This will also help reduce the amount of mineral build up on the front of the unit and nozzle.

Q. There is an unpleasant odor coming from the humidifier. How do I condition the water?
A: If an unpleasant odor is detected, a quick conditioning of the water tank should correct the issue. With the unit off and unplugged, completely drain the water tank (see Care & Maintenance section]. Fill the tank with gallon of drinkable water and add 3 to 5 drops of unscented chlorine bleach to the full water tank.

PREPARATION

Place the heater on a Tim, Level s1 face and plug into a grounded 120 V, 60 Hz power outlet and turn on the power switch on the are of the unit. Only operate heater in upright position. inset two AM batteries into the remote control before using batteries not included. *[Not all products will include a remote control.

Please note that infrared the do not heat like a the additional space heater: You should not expect infrared heaters to blow hot air Like a traditional space heated Infrared heater heat objects not air. Infrared heaters intended to supplement an already heated, insulated mom. Squared footage specifications assume a single enclosed room not an entire home. Infrared heaters do not heat through walls, floods, and are not intended to place a main heat souse. Infrared heat can take at least 24 hours to warm a room but operate much efficiently to maintain the desired temperature. Infrared heaters will not work well in uninsulated unheated spaces like screened in porches, RV’s, garages, unheated basements, etc.

AD DING WATER TO THE HUMIDIFICATION TANK

1. While the unit is off and unplugged, unscrew the water cap by turning counter-clockwise.

2. Add 0.75 gallon of distilled water: DO NOT OVER FILL THE TANK. Replace the top cap and gently tighten. DO NOT OVER TIGHTEN THE CAP.
   Note: Distilled Water discourages calcium build-up in the water tank and on the humidifier nozzle.

3. Replace the top cap by turning clockwise and tightening filmy.
   Note: Due to air build-up during water filling, It is important to turn the humidification setting tor at Least 2 minutes each time after adding water to proven water from leaking out of the unit.

TROUBLESHOOTING

CONTROL PANEL

REMOTE CONTROL

OPERATING INSTRUCTIONS

CARE AND MAINTENANCE

WARNING: Before performing any maintenance task, turn off the power switch in the rear of the unit, unplug the unit, and allow it to cool completely.

1. To keep the heater clean, clean the outer shell with a soft, damp cloth. Use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth.
   CAUTION: DO NOT let liquid enter the heater.

2.  DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater.

3.  DO NOT immerse the heater in water.

4. Wait until the unit is completely dry before use.

5. If you will not be using the heater for a while, take the batteries out of the remote control and store for future use.

6. Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the original packaging to repack the unit.

CLEANING THE AIR FILTER

1. Clean the air filter [2) after three months or if it appears to be blocking airflow. With the heater unplugged, remove the filter screws [1) as illustrated below. Clean all parts of the filter assembly and allow parts to completely dry.
2.  Reassemble and reinstall the filter [2).

WARNING: Do not use the heater without the filter assembly in place.

ONE-YRAR LIMITED WARRANTY

The manufacture warrants this heater against defects in materials and workmanship on functional parts, for a period of 1 year from the original date of outage. Your sales kept showing the date of put haze of the product is your proof of purchase. Keep it in a safe place for future reference. This warranty is subject to personal use only, commercial or rental applications will not be covered.

This product is made with the highest quality materials and saw antidot be free from defects in materials and w clanship at the time of phase. This limited warranty applies to products manufactured distributed by the manufactory, end in the continental United States, and extends to the original phaser gift recipient. This warranty becomes valid at the time of purchase and terminates either by the specified time frame listed above and wren transfer: Any funds monetary compensations must be claimed through the place of purchase (retailed and not through the manufacturer: Any extended warranties [warranties that cover above and beyond this manufacture warranty) that are sold through a tailed third patty, are not dactyl correlated with this products’ limited warranty, and may be redirected to said entailer triparty for coverage.

This warranty extends through the manufacture of the product, and covers functional parts only. Cosmetics are not covered, unless unequip call deter mined it is a workmanship defect. Shipping damage should be addressed with the shipping company, retailer, or place of purchase, not the manufacture unless the manufacture was the direct shipper.

The manufacture’s sole obligation under this warranty shall be Limited to furnishing the original purchase replacement parts founts deemed pairable by the supplied wanly department. The purchase is responsible furnishing any parts shipped unreturned, if desi red. The purchases responsible to prepay any shipping charges (both ayes) including but not limited to taxes and duties. A exchanged parts and products replaced under this warranty will become the property of manufacture. The manufacture reserves the light to change manufactures of replacement parts coproducts for use, in rodent cove any existing warranty.

The purchase may be asked to provide the supplier with proof of purchase documents (including the date of purchase) if requested. Any evidence of alteration, erasing for very of proof of purchase documents will be just cause to VOID this limited warranty. Products, in which the serial numb has been defaced or removed are not eligible for warranty coverage.

This warranty does not apply if the unit has been sect to negligence, fabrication, misuse, abuse, or pairs, alteration by non-manufacturer authorized personnel, inappropriate installations any case beyond the control of the manufacturer. Examples of warranty invalidation may also include, but are not limited to:

• Use of lacquer or paints in (and around) the heaters
• Heater placed on non-approved surfaces
•  Electrical querulent deficiencies (15-20 amp dedicated outlet)
• Use on extension cords/times/sue protectors/G FCI
• Outdoor applications
• Normal wear/tear/weathering
•  Pet/consumer accidents

The manufacture shall not be liable for any loss due to use (or misuse) of the heater other incidental Inconsequential costs, expense damages without refutable foundations. Undernote circumstances shall the manufacture or any of its sensitives be held liable for injury to any peon or damage to any prophy, however arising. Any implied warranty shall have duration equal of the applicable warranty stated above. Specifications a subject to change without notice obligation.

This limited warranty gives the agonal purchase specific legal rights. Other rights may vary from state to state.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>