Shenzhen Xingchang Technology V5 Wireless Recording Microphone Instruction Manual
- June 5, 2024
- Shenzhen Xingchang Technology
Table of Contents
Xingchang Technology V5 Wireless Recording Microphone
Instruction Manual
Product introduction
Thank you for purchasing our product.
The product is a smart wireless recording microphone that can provide
professional recording live streaming output. It is a plug-and-play type,
which requires no APP. Multiple
purposes: Network broadcast, Vlog shooting, program interview, interview
recording, and video teaching.
Function introduction
Function introduction of receiver
-
On/Off key: Hold the key to turn it on/off.
-
Indicator light:
Slow flicker: Fail to connect with the emitter successfully
On: Successfully pair with emitter
Rapid flicker: low battery -
Charging indicator light: The red light will be on while charging and will be off once it is fully charged.
-
Charging port/recording output port
-
Auxiliary wheat: flashing indicates that the auxiliary wheat is not connected, and always on indicates that the auxiliary wheat has been connected successfully.
Function introduction of the emitter
-
Radio microphone: This part should aim at the mouth to record the voice.
-
On/Off/mode switch: Hold the key to turn on/off and press it to switch the mode.
-
Microphone volume +: press once and the microphone volume will increase one level
-
Microphone volume -: press once and the microphone volume will decrease one level
-
Charging indicator light: The red light will be on while charging and will be off once it is fully charged.
-
Battery status indicator light: When the battery is full, two indicator lights will be on at the same time, when the battery is less than 40%, indicating that the battery is low and when the battery is too low, one light will flicker.
-
Emitter light: It will be on once it turns on and it will be off when it turns off.
-
Bluetooth light: It flickers when the Bluetooth is not connected and will be on once Bluetooth is connected (Bluetooth serves as the external sound source for playing music and will not serve as a recorder).
-
Mode area: There are two modes available, which are, On/off and mode switch. Vlog mode: It is applicable to shoot short videos and original voice broadcasts. The voice is clear, clean, and free from reverberation. Under this model, the music cannot be played out through Bluetooth.
Live streaming mode: It is applicable for live streaming sing. It comes with reverberation and the music can be played out through Bluetooth. -
Charging port: monitor earphone port
Note: The default is Vlog mode for the first start of emitter and it has a memory function for the second time.
How to use
-
How to connect to the cellphone for voice/video recording.
Step one: Firstly, hold the On/off button on the receiver and emitter to have them paired successfully,
Step two: Connect the receiver with the cellphone through cable Step three: Switch to the Vlog mode of the emitter (the default mode for the first start is Vlog mode) and turn the camera App in the phone to start recording voice and video. -
How to conduct live streaming through cellphone
Step one: Firstly, hold the On/off button on the receiver and emitter to have them paired successfully,
Step two: Connect the receiver with the cellphone through cable Step three: Switch to the live streaming mode of the emitter and use the Bluetooth on the other cellphone to play music for live streaming. Open the live streaming App in the phone to start. -
How to record voice/video by connecting the camera
Step one: Firstly, hold the On/off button on the receiver and emitter to have them paired successfully,
Step two: Connect the receiver with a camera through the camera line Step three: Switch to the Vlog mode of the emitter (the default mode for the first start is Vlog mode) and turn the camera App in the phone to start recording voice and video.
Product parameter
Direction type: All directions
Frequency range: 2.4G
Range of frequency response: 30Hz~18KHz
Transmission distance: 15m
SNR: ≥90DB
Battery capacity: 500Ah/3.7V
Charging port: Type-c
Rated input: DC5V=500mA
Standard charging time: About 1 hour
Working hours: 4-6 hours
Overall dimension (main device): 44X44X23mm
Working temperature: -10°℃~45℃
Storage temperature: -20°C~60℃
Packing list
Contents of the packing list
- Emitter
- Receiver
- Instruction manual
- Charging line 1, camera line 1, cellphone cable*1
- Storage box
- Packing box
Manufacturer information
Product name: Wireless recording microphone
Product model: V5
matters need attention
- Please disconnect the charger and turn it off before cleaning the machine.
- Non-professionals should not disassemble the equipment by themselves to avoid machine failure and loss of warranty rights.
- Do not place the equipment in direct sunlight to avoid premature aging of electronic parts.
- Avoid using in dusty or dirty places (dust can easily cause equipment failure).
- Please do not place the equipment in a supercooled or overheated environment, which may cause the equipment to fail to operate normally.
- It is recommended that the set ambient temperature should not exceed -10C-40℃and the relative temperature should be 10%-95% c.
- Please don’t put anything into the equipment to avoid short circuits of parts or circuit damage. Please don’t spill any liquid on the product.
- Avoid the friction and impact between the machine and hard objects, so as to avoid scratching or falling off the surface or damage to other hardware.
- The product shall not be exposed to overheating environments such as sunshine, fire, or the like.
- The manual contains important information, so please keep it.
Warranty policy
Warranty range: For damage not caused by humans, the device can be replaced within one month and can be provided with free maintenance within one year. Limited maintenance is available within three years.
Warranty card
Product model
Date of purchasing
Retailer
Maintenance record
Customer name
Contact phone
Contact address
Note: The
products of the company will be updated continuously, further notice may not
be made for any change.
This device complies with part15°f the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested are found to comply with the limits
for Class a digital device, pursuant to Part 15 of the FCC Rules. These limits
were redesigned to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that reference will not occur in a particular
installation.
If this equipment does cause ha Trail! interference to; ado or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by color more of the
following measures:
—Rborientorrelocatetherweivinganterina.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different From that to
which the receiver isconnected.
—Consult the dealer n experienced radiorVtechnicianforhelp.Thedeirice has been
evaluated to meetgeneraIRF exposure requirement. The device can be used in
portable exposure conditions without restriction
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>