BLUEDRY HD-BD88 ECO Friendly User Manual

June 12, 2024
BLUEDRY

BLUEDRY HD-BD88 ECO Friendly User Manual
BLUEDRY HD-BD88 ECO Friendly

TECHNICAL SPECIFICATIONS

Item Category Performance Data
Operating Voltage 220 – 240Vac, 50Hz, 880 WATTS
Warm Air Speed Output 103 m/s
Noise Level 78dBA @ 1 meter
Air Output Temperature 77°F (25°C) – Ambient Temperature 68°F (20°C)
Motor Type 650 Watts, 23,000 rpm, Brush Type, Dual Ball Bearings
Motor Thermal Protection Auto Resetting Thermostat turns unit off, 240V

at 221°F (105°C) – EURO Spec
Heater Element| 230W
Heater Thermal Protection| Auto Resetting Thermostat turns unit off at, 149°F (65°C)
Drying Time| Less than 15 seconds
Circuit Operation| Infrared Automatic, self adjusting
Sensor Range| 100 mm
Timing Protection| 60 seconds auto shut off
Drip Proof| IP22
Isolation| CLASS 11 double insulated
Net Weight| 4.5 kg
Shipping Weight| 5 kg
Unit Size| 255mm W x 525mm H x 172mm D
Finish| ABS Silver – HD-BD88S ABS White – HD-BD88W

GENERAL SAFETY INFORMATION

WARNING

Failure to properly ground unit could result in electrical shock and/or death.

This product is intended for installation by a qualified service person. Use AWAG No.16 solid conductor for wiring.

Disconnect power at the service breaker before installing or servicing. NOT FOR HOUSEHOLD USE – MAY CAUSE BURNS

NOTE: Do not install dryer over wash basin.

Type Y attachment

If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard.

Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

RECOMMENDED MOUNTING HEIGHTS

From floor to bottom of air outlet.

Men’s| Ladies| Children, ages 11-17| Children, ages 3-10| Disabled
---|---|---|---|---
43”| 41”| 39”| 33”| 35”
109 cm| 104 cm| 99 cm| 84 cm| 89 cm

INSTALLATION

Installation must be carried out by a qualified electrician

  1. Make sure power supply breaker is switched off. Installation must be carried  out in accordance with the current editionof the local wiring regulations code having jurisdiction. Installation should be performed only by a qualified electrician.

  2. Place template against wall at desired height (see mounting height recommendations) and mark locations of

  3. Mounting holes and wire service entry at knockout (KO) location.
    NOTE: Two or more dryers should be no closer than 24 inches (610 mm) on centre.

  4. Remove and retain 2 cover screws and cover.

  5. Connect supply wires to terminal block where indicated and connect ground wire to baseplate with ground screw.
    Connections:
    a. Connect the live wire (coloured red or brown) to the terminal block marked “L”.
    b. Connect the neutral wire (coloured black or blue) to the terminal block marked “N”.
    Note that the colour of live and neutral wires depends on voltage of supply service.

  6. Replace cover. Do not over-tighten screws.

INSTALLATION CONT

  1. Fix the water tank to the hand drier with the screws attached.

  2. Drill three holes of 6mm diameter.
    Installation Instruction

  3. Fix the hanging board to two holes which are at the top by using the plugs and screws

  4. Make a breach on the cover according to the position of the power cord coming out before pulling out the power cord. Follow arrow A, hang the drier on the hanger board. Follow the arrow B, pull out the water tank and fix the hole at the bottom with the screws attached. Put back the water tank.

  5. In order to meet different installation environments the induction sensibility is set at the most sensitive point. If this unit over runs or does not work after installing, please adjust
    Installation Instruction

CLEANING & MAINTENANCE

Check the water tank 1-2 times a week and empty before it reaches the full mark.

Take out the air filter mesh from this appliance, clean it once a week and refix.

All surfaces of the unit should be cleaned daily with a soft cloth dampened with warm, soapy water. Polish with a soft dry cloth.
Cleaning Instruction

DIAGRAM

Diagram

1 Power indicator light
2 Front cover
3 Motor housing
4 Rubber washer
5 Shock absorber
6 Motor rubber
7 Motor and fan module
8 Blower housing base plate
9 Blower housing cover
10 Terminal block
11 Cable clamp
12 Base plate
13 Wall fixing bracket
14 Circuit board module
15 Water tank
16 Wall fix bracket
17 Water tank cover
18 Water tank
19 Air outlet gasket
20 Heating element
21 Air outlet
22 Fixing screw
23 Bottom plate
24 Filter
25 Sensor PCB module
26 Sensor screen
27 Front cover flange

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals