NDS SCE 320 Suncontrol2 MPPT Regulator User Manual

June 10, 2024
NDS

NDS SCE 320 Suncontrol2 MPPT Regulator

NDS-SCE-320-Suncontrol2-MPPT-Regulator-PRO

SAFETY INSTRUCTIONS

  • Child Safety: Keep the device Out of Reach.
  • Carefully check the integrity of the device and connectors.
  • To avoid overheating and possible fires do not install the device in a sealed environment, Always choose a well ventilated area.
  • Do not place the device on highly flammable surfaces or environments (eg: paper, cloth, etc.).
  • Do not cover the cooling slits on the side and the fan on the top.
  • Do not install the device near flooded batteries: they produce flammable, corrosive and explosive gas while working, and it can damage the product.
  • protect the device from sunlight or direct sources of heat.
  • To avoid malfunctions, DO NOT install and use the device in very humid environments, in contact with water splashes, various liquids, or exposed to rain.
  • To avoid risk of electric shock and/or fire, the vehicle’s fuel system must be in good condition.
  • In case of damaged connecting cables or inadequate section, immediately replace them with suitable cables as specified by this manual or by a qualified electrician.
  • In case of anomalies in the conformity of the product do not use it! it is strictly forbidden to open the device. Repairs may only be carried out by qualified technical personnel using original spare parts.
  • Keep the instruction manual near the device for easy access to the essential safety, use and maintenance information.
  • The information contained in this manual may be changed without notice. NDS Energy s.r.l. reserves the right to make changes and improvements to the product at any time without notice and without obligation to apply these changes to the devices previously distributed.
  • The images of the products are purely indicative and may therefore not be fully representative of the characteristics of the product, differing in colour, size or accessories

PACKAGE CONTENTS

Check the contents of the package:

  • 1 x SUNCONTROL2
  • 1 x Replacement fuse
  • Wall mounting screws

DESCRIPTION

SUNCONTROL2, the automatic solar regulator with MPPT technology to push the efficiency of photovoltaic modules to the maximum: more energy, less space. The MPPT algorithm always uses the “maximum power peak” delivered by the panel, with a significantly higher performance than the PWM technology (up to 25% more)
SUNCONTROL2 available in two models SCE 320 and SCE 360, manages (depending on the model), up to 350W input, with a maximum charge of 25A. The new microprocessor, equipped with OPTICHARGE firmware, performs up to 6 charging phases, including desulphation and maintenance phases, for optimal recharging of the on-board batteries.
SUNCONTROL2 is compatible with the following battery technologies: GEL, AGM, Wet and LiFePO4 and both the leisure batteries and the starter battery can be recharged. The state of charge (SoC) of both connected batteries is immediately visible on top of the device thanks to the two multicolored LEDs. The system works with a 12V nominal voltage and it is possible to connect two photovoltaic panels, on separate inputs, with a maximum power of 180Wp (depending on the model). The Dip Switch selector, located next to the power connections, allows you to select the output charge curve in a simple and fast way. The touch screen display DT002 (optional) with new management software, allows you to view the charge information and set the various settings with the new communication protocol NDS.

MAIN FEATURES

  • MPPT technology (+25% performances)
  • Charging curve selection: GEL, AGM, Wet, and LiFePO4
  • New Firmware OPTICHARGE
  • Up to 6 charging phases
  • Starting battery charge
  • Desulphation curve
  • Independent inputs for 2 solar panels
  • SoC Quick view with status LEDs
  • Touch screen Display (Optional)

OPERATIONS

SUNCONTROL2 charges up to two batteries: one service battery (B1) and one starter battery (B2), with priority charging to the service battery. SUNCONTROL2 will start charging the batteries if the following conditions are satisfied:

  1. The connected Solar Panels deliver a voltage 1V higher than the voltage of the batteries to be recharged.
  2. Battery voltage higher then 8V.

The Leisure Battery will be charged with the selected curve. The Starting Battery will be charged if the following conditions are satisfied:

  • Leisure battery charged between 80% and 100%.
  • Starting battery with voltage under 12,5V.

Every charging phase have a maximum run time, with the exception of the maintenance phase, which constantly monitors the state of charge and, if necessary, delivers an impulse current to keep the battery 100% charged.

NOTE
If the photovoltaic panels interrupt the power supply (during night, shadowed solar panel, etc. …) the system goes into Stand- By mode: LEDs off and self- consumption to the minimum (<2mA).

STRUCTURE

FRONTAL CONNECTION

NDS-SCE-320-Suncontrol2-MPPT-Regulator- \(1\)
CONNECTION| FUNCTION
1| Display Bus DTB01 connection
2| N-BUS network connection
3| Solar panel negative connection
4| Battery negative connection
5| Solar panel positive connection 1
6| Solar panel positive connection 2
7| Leisure battery positive connection (B1)
8| Starter battery positive connection (B2)
9| Dip Switch – Charging curve selection
10| Temperature probe connection

N-BUS NETWORK AND CONTROLLERS

N-BUS devices can be networked for optimal operation of the entire NDS energy system. To start setting up your new energy system, simply connect two or more N-BUS devices with the optional data cable, available in various lengths (BC03M, BC06M or BC 10M). Furthermore, with N-BUS, you can use a single controller to monitor and control all NDS devices.
Manage the SUNCONTROL2 and all N-BUS devices with a single touch screen full color display (DTB01), or with the mobile app for smartphones, if there is at least one NDS device with Bluetooth in the network. Bluetooth devices are e.g. SUNCONTROL2 (models with Bluetooth) and TEMPRA Lithium Battery (all models). The mobile app can also be used to update all connected N-BUS devices if there is a Master device, such as TEMPRA Lithium Battery.NDS-SCE-320-Suncontrol2
-MPPT-Regulator- \(2\)

NOTE A Bluetooth N-BUS device is required to use the Mobile App, such as TEMPRA Battery or SUNCONTROL2 models SCE 320B, SCE 360B. The Mobile App does not work with the SCE 320, SCE 360 or the earlier SC320M and SC350M models.

INSTALLATION

Place the SUNCONTROL2 on the chosen surface and secure the entire device using the fixing holes integrated in the shell with the supplied screws or equivalent (Fig.1).NDS-SCE-320-Suncontrol2-MPPT-Regulator- \(3\)

All electrical and setup connections are on the front, it is not necessary to disassemble the plastic shells, except for the protection fuse replacement.
On the front side, after the power connections, there’s a Dip Switch for the charging curve selection, it’s important to select the correct curve according to the type of battery supplied, for the selection of the correct curve please refer to the chapter “Charging curve selection”.

CAUTION

  • For electrical connections, use cables of appropriate cross-section: from 6 mm2.
  • In case of a long stay, it is advisable to disconnect the negative cable from the device to completely neutralize any residual consumption that may inadvertently discharge the leisure battery.

BASIC CONNECTIONNDS-SCE-320-Suncontrol2-MPPT-Regulator-
\(4\)

CHARGING CURVE SELECTION

The Dip Switches, located next to the power connections, allow you to select the proper charging curve for the installed services battery, use the table to set the correct curve for your battery. The Dip Switches affect the B1 charging curve (leisure battery), not B2 (starter battery). The B2 charging curve is preset to curve N°1 (GEL – Desulphation OFF).NDS-
SCE-320-Suncontrol2-MPPT-Regulator- \(5\)

NOTE

  • The default setting is Curve 1 for GEL batteries – desulphation OFF.
  • In order to safeguard the battery, with an ambient temperature below 0°C, the LiFePO4 charge curve will not be started.

CHARGING CURVENDS-SCE-320-Suncontrol2-MPPT-Regulator-
\(6\)

B1 – PHASE DISCUSSION

PULSE CHARGE| With voltage between 8V and 10.5V, a current between 1A and 2A will be delivered, every 5 seconds. Timeout 4 hours.
RECONDITIONING| With voltage between 10.5V and 12.0V, an approximately 2A costant current will be delivered. Timeout 8 hours.
BULK CHARGE| With voltage between 12V and Vmax (Maximum voltage of the selected charging curve), will be delivered a constant current of: 20A model SCE 320 and 25A model SCE 360.
ABSORPTION CHARGE| With battery voltage equal to Vmax (Maximum voltage of the selected charging curve), will be delivered a costant voltage equal to the selected curve Vmax. The delivered current will decrease as the battery state of charge increases till about 3A. Timeout 6 hours.
---|---
DESULPHATION| An approximately 2A constant current will be delivered, allowing the battery voltage to rise independently to the maximum value of 15.8V. This phase ends to the achievement of 15.8V. Timeout 2 hours.
MAINTENANCE| This phase keep a constant voltage  related  to the selected charging curve (Vmaint). This phase has a 4 hours timeout for the LiFePO4 charging curve with maintenance ON (curve N°7), while  for the other curves there’s no time limit. If during the maintenance phase the  voltage should fall below 13.15V for LiFePO4 curve and 12.65V Wet curve and 12.8V and for the other curves, charge will be restarted from the first phase. Timeout 4 hours.
B2 – PHASE DISCUSSION
PULSE CHARGE| With voltage between 8V and 10.5V, a variable current between 1A and 2A, every 5 seconds. Timeout 4 hours.
RECONDITIONING| With voltage between 10.5V and 12.0V, an approximately 2A costant current will be delivered. Timeout 8 hours.
BULK CHARGE| With battery voltage between 12V and 14,4V, will be delivered a 5A constant current.
ABSORPTION CHARGE| With battery voltage 14,4V will be delivered a 14,4V constant voltage. The delivered current will decrease as the battery state of charge increases till about 3A. Timeout 6 hours.
MAINTENANCE| This phase keep a constant voltage of 13,5V. Timeout 8 hours.

LED INDICATORS

The two LEDs on the upper part of the device, marked B1 and B2, allow you to quickly understand the charge status of the connected battery. Each LED can emit different colors referred to a precise state of charge of the battery, the table below explains the relationship between the LED color and the battery state of charge.

SIGNAL MEANING
Red LED Charging
Orange LED Reconditioning
Green LED Fully charged / Maintenance

CAUTION A fast flashing of both LEDs (with the solar panel active) shows an error due to the internal fuse breaking, or services battery voltage below 6V.

FUSE REPLACEMENT

If the protective fuse on the SUNCONTROL2 electronic board is damaged, it can be replaced with the original replacement fuse (supplied) or with a common 25A (for SCE320) or 30A (for SCE360) automotive fuse.NDS-SCE-320-Suncontrol2
-MPPT-Regulator- \(7\)

Follow these steps to reach the fuse:

  1. Remove SUNCONTROL2 from its housing.
  2. Rotate the device to reveal the screws on the bottom of the device.
  3. Unscrew the 4 screws.
  4. Remove the front shell of SUNCONTROL2 to access the fuse.
  5. Replace the fuse.

TECHNICAL FEATURES

DESCRIPTION SCE320 SCE360

INPUTS
Maximum input Voltage solar panels (open circuit voltage)| 29,5V| 29,5V
Solar Panel input Connections| 2| 2
Solar Panel input Maximum Power Suppoerted| 50W – 160W| 50W – 200W
OUTPUT B1
Battery nominal voltage| 12V| 12V
Charging current maximum output| 20A| 25A
Minumum battery capacity required Lead-acid| 60Ah| 80Ah
Minumum battery capacity required LiFePO4| 40Ah| 50Ah
Mimumum battery voltage required| 8V| 8V
Charging curve selector/Curves number| Yes/8| Yes/8
Temperature regulated fan speed| No| Yes
Temperature regulated charging (by temperature sensor for B1 battery – optional)| Yes/-30mV/°C| Yes/-30mV/°C
OUTPUT B2

Battery nominal voltage| 12V| 12V
Charging current maximum output| 5A| 5A
Minumum battery capacity required Lead-acid/LiFePO4| 15Ah/10Ah| 15Ah/10Ah
Minimum/maximum voltage starting charge| 8V – 12,5V| 8V – 12,5V
Maximum charging voltage| 14,4V| 14,4V
Temperature regulated fan speed| No| Yes
Maximum charging timeout| 8h| 8h
GENERAL

Charging algorithm OPTICHARGE| Yes| Yes
Stand-by self-consumption| <2mA| <2mA
Display connection| Yes| Yes
Internal protection fuse| 25A| 30A
Reverse polarity protection| Yes| Yes
Night-time discharge protection| Yes| Yes
Overload protection| Yes| Yes
Overheating protection (output power reduction)| Yes| Yes
Size (mm)| 123 x 108 x 50| 123 x 108 x 50
Weight (cables excluded)| 400g| 420g
Working temperature| -20°C/+50°C| -20°C/+50°C
Ambient humidity| <90% no condensation| <90% no condensation
Maximum altitude| 3000m maximum nominal output up to 2000m)| 3000m (maximum nominal output up to 2000m)

WIRING DIAGRAMS SAMPLES

Simple connection, with solar panels, bus display (optional).NDS-
SCE-320-Suncontrol2-MPPT-Regulator- \(8\)

Connection with solar panels, bus display (optional), original control unit .NDS-SCE-320-Suncontrol2-MPPT-Regulator- \(9\)

Connection with solar panels, display bus (optional), original control unit and TEMPRA lithium battery.NDS-SCE-320-Suncontrol2-MPPT-Regulator-
\(10\)

F.A.Q.

  • About solar panels, what’s the maximum voltage supported by SUNCONTROL2?
    Maximum supported voltage is 29,5V.

  • Is it possible to connect one 200W solar panel only, on a single SUNCONTROL2 connection?
    It’s possible to connect just one bigger solar panel (200W), for example on SUNCONTROL2 Pin N°5, but you must connect Pin N°5 and Pin N°6. For the connection bridge, please use, at least, a 6 mm2 cross-size cable.

  • Is it normal to have a battery voltage (with solar regulator working) over 15V?
    It’s normal when the device is in desulphation mode. It is possible to turn OFF the desulphation selecting the proper charging curve: look at the chapter “Charging curve selection”.

DECLARATION OF EU CONFORMITY – SUN CONTROL 2

  • Company: NDS Energy s.r.l.
  • Address: via Giovanni Pascoli, 96/98 65010 – Cappelle sul Tavo (PE) Italy

Declares under its own responsibility that the product:

  • Commercial Name: SUN CONTROL2
  • Models: SCE320, SCE360, SC320M, SC350M SCE320B, SCE360B

To which this declaration refers, is in compliance with the provisions of the Directive of the Council of the European Union concerning the electromagnetic compatibility (EMC) Directive 2014/30/EC, demonstrated to the observance of the following norms:

  • EN55014-1:2017+A11:2020
  • EN55014-2:2015
  • EN IEC 61000-3-2:2019
  • EN61000-3-3:2013+A1:2019
  • EN IEC 61000-6-1:2019
  • EN IEC 61000-6-2:2019
  • EN IEC 61000-6-3:2021

It also complies with Directive 2014/53/EU (RED) for wireless communications equipment, demonstrated by compliance with the standard:

EN 300220
For models with BLE connectivity: SCE320B and SCE360B, the radio equipment directive (RED) 2014/53/UE applies to compliance with the following regulations:

  • EN62368-1:2020+A11:2020
  • ETSI EN 301489-1 V2.2.3 (2019-11)
  • ETSI EN 301489-17 V3.2.4 (2020-09)
  • EN 300328 v2.2.2 (2019-07)
  • EN50663:2017

compliance for radiated emissions and electromagnetic immunity on vehicles is demonstrated in compliance with the directive:

ECE R10
compliance with the restriction on the use of hazardous substances is demonstrated by compliance with directive 2011/65/EU (ROHS2).

WARRANTY

Warranty coupon

  • FIRST Name ____
  • surname __
  • postcode _____
  • E-MAIL ____
  • model _____
  • SERIAL NUMBER _____
  • Purchase date _____

I CONSENT TO THE ACTIVITY DESCRIBED IN POINT 3.C OF THE INFORMATION NOTICE ON www.ndsenergy.it/privacy-policy/

NDS ENERGY S.r.l.
Via G. Pascoli, 96/98 65010 Cappelle sul Tavo (PE) Italy
email: customer@ndsenergy.it
tel: +39 085 4470396
fax: +39 085 9112263
Italy

NDS ENERGY S.R.L.
Via G. Pascoli, 96/98
65010 – Cappelle sul Tavo (Pe) Italy
Tel.: +39 085 4470396
Web: www.ndsenergy.it
Email: customer@ndsenergy.it
LIKE US: facebook.com/ndsenergysrl

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals