COSTWAY HW50956 Security Safe Box User Manual
- June 5, 2024
- COSTWAY
Table of Contents
HW50956 Security Safe Box
User Manual
USER’S MANUAL
Security Safe Box
HW50956
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ
AND KEEP FOR FUTURE REFERENCE.
With your inspiring rating, COSTWAY will be more consistent to offer you EASY
SHOPPING EXPERIENCE, GOOD PRODUCTS, and EFFICIENT SERVICE!
First, read the manual carefully before you start using the safe.
Product description:
This product is designed for moderate security risks in domestic premises and
is not fire-resistant.
Installation:
Choose a location where this product will be convenient to use, but not easily visible to an intruder. Inside a fitted wardrobe or cupboard is often suitable. If possible, select a position where the unit can be bolted to both wall and floor as security will be much higher if it is fixed to two surfaces. Wall fixing must always be to a solid wall, not a stud wall.
Preparation for use:
This product is battery-operated. Batteries are not supplied. Only use 1.5V AA
batteries. For your convenience, we have engineered a manual override system
for your safe. To open the door of the safe for the first time, just remove
the battery cover plated (d)(see diagram 1). You will find the keyhole, insert
the key into the keyhole and turn it in a counter-clockwise direction, turn
the knob (a) in a clockwise direction. This will manually open your safe.
To install the batteries
After opening the safe, just remove the battery cover plate and install the
four batteries. Ensure the + and positions are correct. The display (e) will
scan the status of the electronic system automatically. If it is in order the
display will show “goods”.
Opening the safe after installing the batteries:
To open the door of the safe, press the button “START”(c) (see diagram 1), the
display on the panel will show”—–“, then input one of the two sets of factory-
preset codes:
0.0.0.0.0.0. (user code) or 8.8.8.8.8.8.(master code) immediately confirm by
pressing the button “START”. The display will show “OPEN” and use the knob
within 4 seconds.
Setting the code:
The safe can be programmed with two sets of codes. For your safety, after
opening the safe and installing the batteries, you should set two sets of new
codes to replace the two sets of factory preset codes.
Programming the user code:
A.Press the red button(b)(see diagram 2), then release it and display on the
panel will show”—–” ”
B.Press “START” immediately.
C. Now press the 6 digits that you wish to use as a new user code. The display
will show “IN” and your inputting numbers. It means that the new user code is
confirmed.
Programming the master code:
A.Press the “START” button. The display will show “—–“.
B. Now input your new 6 digits
C.Press the red button inside (b) (see diagram 2). The display will show “IN”.
It means that the new master code is confirmed.
If you or an intruder uses the incorrect group of numbers, the display will
show “ERROR” and it will not open. If the incorrect combination code is used 4
times consecutively, the display will show “ERROR” and the system cannot be
entered until 3 minutes later. The override key can be used to open the door
during the 3 minutes. If the key is used to open the door, the buzzer can be
cleared by pressing the red button.
Battery replacement:
To test the batteries, just press the button “START”. If the batteries are
low, the display will show “LOBAE”, AND YOU SHOULD REPLACE THE BATTERIES. The
safe requires 4 X size “AA” (1.5V R06) batteries. Replace the old battery, the
display will scan the status of the electronic lock system automatically. If
it is in order, the display will show “GOOD”. The use of alkaline batteries is
recommended.
Override key:
For your convenience, we have engineered a manual override system for your
safety. If you forget or misplace your combination, remove the battery cover
place and take out the batteries. You will find the keyhole, insert the key
into the keyhole and turn it in a counter-clockwise direction, turn the knob
in a clockwise direction. This will manually open your safe at any time. This
product is supplied with 2 original keys.
Do not keep the key in your safe. In event of battery failure, you will not be
able to open the safe.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>