COSTWAY HW51993 Security Safe Box User Manual
- June 5, 2024
- COSTWAY
Table of Contents
COSTWAY HW51993 Security Safe Box
With your inspiring rating, COSTWAY will be more consistent to offer you EASY SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE!
DEPOSITORY SAFE OPERATION MANUAL
First read the manual carefully before you start using the safe. Do not keep the key in your safe. In event of battery failure you will not be able to pen the safe.
Product description:
The safe box is designed for protecting your cash.
This safe is great for accepting coin bags. The deposit drawer is located at
the front of the safe and works in the same way as a post office box does.
Installation:
Choose a location where this product will be convenient to use, but not easily
visible to an intruder. Inside a fitted wardrobe or cupboard is often
suitable. If possible, select a position where the unit can be bolted to both
wall and floor as security will be much higher if it is fixed to two surfaces.
Wall fixing must always be to a solid wall, not a stud wall.
Preparation for use:
This product is battery operated. Batteries are not supplied. Only use 1.5VAA
batteries. For your convenience, we have engineered a manual override system
for your safe. To open the door of the safe for the first time, just remove
the battery cover plated (d) (see diagram 1). You will find the keyhole,
insert the key into the keyholeand turn it in a counter-clockwise direction,
turn the knob (a) in a clockwise direction. This will manually open your safe.
To install the batteries
After opening the safe, just remove the battery cover plate and install the
four batteries. Ensure the + and – positions are correct. The display (e) will
scan the status of the electronic system automatically. If it is in order the
display will show “goods”.
Opening the safe after installing the batteries:
To open the door of the safe, press the button “START”(c) (see diagram 1), the
display on the panel will show”—–“, then input one of the two sets of factory-
preset codes: 0.0.0.0.0.0. (user code) or 8.8.8.8.8.8.(master code)
immediately and confirm by pressing the button “START”. The display will show
“OPEN” and use the knob within 4 seconds.
Programming the code:
The safe can be programmed with two sets of codes. For your safety, after
opening the safe and installing the batteries, you should set two sets of new
codes to replace the two sets of factory preset codes.
Programming the user code:
- When the main safe door is open, Press the red button (at the back of door, near the hinge), then release it and display on the panel will show”—–“
- Press “START” immediately.
- Now press your 6 digits that you wish to use as a new user code. The display will show “IN” and your inputting numbers. It means that the new user code is confirmed.
Programming the master code:
- When the main safe door is open, Press the “START” button. The display will show “—–“.
- Now input your new 6 digits
- Press the red button inside (at the back of door, near the hinge). The display will show “IN”. It means that new master code is confirmed.
If you or an intruder uses the incorrect group of numbers, the display will show ”ERROR” and it will not open. If the incorrect combination code is used 4 times consecutively, the display will show “ERROR” and the system cannot be entered until 3 minutes later. The override key can be used to open the door during the 3 minutes. If the key is used to open the door, the buzzer can be cleared by pressing the red button.
Battery replacement
To test the batteries, just press the button “START”. If the batteries are low, the display will show “LOBAE”, AND YOU SHOULD REPLACE THE BATTERIES. The safe requires 4 X size “AA” (1.5V R06) batteries. Replace the old battery, the display will scan the status of the electronic lock system automatically. If it is in order, the display will show “GOOD”. Use of alkaline batteries is recommended.
Override key:
For your convenience, we have engineered a manual override system for your
safe. If you forget or misplace your combination, remove the battery cover
place and take out the batteries. Your will find the keyhole, insert the key
into the keyhole and turn it in a counter-clockwise direction, turn the knob
in a clockwise direction. This will manually open your safe any time. This
product is supplied with 2 original keys. Do not keep the key in your safe. In
event of battery failure you will not be able to open the safe.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>