dreametech T30 Cordless Vacuum Cleaner User Manual

dreametech T30 Cordless Vacuum Cleaner

THANK YOU
FOR PURCHASING THIS DREAME VACUUM CLEANER.

Registration Quick Start
Welcome to register a Dreame account by scanning the QR code.
You are available for the User Manual and Special Offers.

With it you are obtaining a high quality product that is engineered for optimal performance. If you have any questions on the product, please contact us: aftersales@dreame.tech.

Safety Information

IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE). Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
SAVE THESE INSTRUCTIONS
Household use only.

WARNING – To reduce the risk of fire, electric shock, or injury:

• Do not use outdoors or on wet surfaces.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children, pets or plants.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle charger, including charger plug, and charger terminals with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dust cup and/or filters in place.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery pack, picking up or carrying the appliance. Carrying the appliance with your finger on the switch or energizing appliance that have the switch on invites accidents.
• Disconnect the battery pack from the appliance before making any adjustments, changing accessories, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.
• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.
• Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
• Do not modify or attempt to repair the appliance or the battery pack except as indicated in the instructions for use and care.
• Do not use and store in extremely hot or cold environments (below 0℃/32°F or above 40℃/104°F). Please charge the cordless vacuum in temperature above 0℃/32°F and below 40℃/104°F.

Caution:
This device complies with Part 15 of the FCC Rules / Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following.

Product Overview

Accessories

Note: The images in this manual are for illustrative purposes only. The actual product may differ.

Component Names

Introduction of Display Screen

Note

• The color of dust level indicator changes with the amount of inhaled dust.
• Residual time is for reference only and it may be different from the actual time.

Installation

Vacuum Installation Diagram

Accessories Installation Diagram

2-in-1 Charging & Storage Mount Installation Diagram
(The 2-in-1 charging & storage mount is an optional accessory. You can install it based on your needs.)

Note:
The 2-in-1 charging & storage mount should be installed in a cool, dry place with an electrical outlet nearby. Prior to installing, ensure that there are no electrical wires or pipes in the space directly behind where the mount will be installed.

1. The bottom of the mounting template sticker should be level and at least 41″ from the ground, and its top should have at least 12″ of clearance above it.(12″ : Leave enough space just in case you may need to purchase the replaceable battery in the future.)
2. Use a power drill with an 0.315” drill bit to drill a hole into each hole marker on the mounting template sticker, then insert a wall plug into each hole.
3. Align the locating holes on the mount with the holes on the wall. Fasten it to the wall with the included screws.

Charging

Fully charge the vacuum before using it for the first time.

Note:

• A full charge will take approx. 4 hours.
• Vacuuming in Turbo Mode for a prolonged period will cause the battery to heat up, which increases charging time. Allow the vacuum to cool down for 30 minutes before charging it.

Charging Methods
Charging the vacuum with the charger

Charging the vacuum on the charging mount

Battery Status Display
Display Screen
The number on the display screen represents the current battery level in a percentage during charging. When the number becomes 100, the battery is fully charged.

LED Battery Status Indicator
When charging, the indicators blink white. When the charging is completed, the indicators keep solid white.

Note:
Once the vacuum is fully charged, the indicator will turn off after 5 minutes, and the vacuum will enter energy-saving mode.

How to Use

Setting Language
Press and hold the button for 3 seconds to enter the menu interface. Click the button to swtich to “Language”. Press the button for 1 second to enter the language selection interface. Click to scroll through the language list, select a language, and then press and hold for 3 seconds to save your setting.

Cleaning Record
Press and hold the button for 3 seconds to enter the menu interface. Click the button to swtich to “Cleaning Record” and press the button for 1 second to enter the cleaning record interface. Then you will see the cleaning record of the last 7 days.

Note:

• The display screen will return to the main page if there is no operation for more than 15 seconds.
• To exit the menu interface, click the button to select “Exit”.

Switching Suction Level
Press the button to switch between four suction levels of auto, eco, med and turbo. The corresponding suction level will be highlighted on the display screen.
The color of dust level indicator changes with the amount of inhaled dust. When the smart multi-brush bar is attached, the vacuum will automatically switch the suction level between the floor/tile and the carpet.
Note: Stop the vacuum at any time while cleaning. It will continue to use the last selected suction level when starting again.

Working Methods
Select from two working methods for the vacuum, which can be selected based on your own needs.
When the vacuum is running, it will monitor the amout of inhaled dust within 1 second. The amount of dust will be displayed by the color of dust level monitoring curve on the screen in real time.

Method 1 : Discontinuous Cleaning Mode
Press and hold the switch of the vacuum to enable this mode, and release it to stop immediately.

Method 2 : Continuous Cleaning Mode (Electronic Lock)
Click the electronic lock key to switch to Continuous Cleaning Mode, and then briefly press the on/off switch to keep the vacuum in Continuous Cleaning Mode.
Use the electronic lock to free your fingers from fatigue caused by holding the switch.

Note:

•  -In this mode, briefly press the on/off switch to suspend the operation or start again and the working mode of the vacuum will not change
• Click the electronic lock again to quit Continuous Cleaning Mode.

Using Different Accessories

Smart Multi-Brush Bar
For cleaning floors such as marble, tile, and low pile carpet. When Auto Mode is activated, the vacuum will automatically adjust its suction level depending on the surface type.
Note: The smart multi-brush bar can be attached directly to the vacuum.

Mini Electric Brush
For vacuuming dirt, pet hair, and other stubborn debris from sofas, bedding, and other fabric surfaces.
Note: It is not recommended to vacuum on fragile surfaces, such as silk.

2-in-1 Brush Nozzle
For vacuuming dust from curtains, keyboards, ceilings, sofas, vehicle interiors, coffee tables, etc.

Soft Dusting Brush
Suitable for vacuuming on LCDs, keyboards, lampshades, curtains, shutters and other surfaces of fragile objects.

Extension Hose
It is suitable for vacuuming the corners that are not easily accessible such as drawers, cars interior, and in the bottom of sofa when used with soft dusting brush or 2-in-1 brush nozzle.

Flexible Adapter
Bending and extending the rod with one click can easily reach under low-lying furniture, such as bed and sofa.

LED Crevice Nozzle
The nozzle is equipped with a thin suction opening and LED light. It is suitable for vacuuming the debris in the narrow places.

Note:

• If any rotating part becomes stuck, the vacuum may shut off automatically. Remove any trapped objects so the device can function normally.
• When the battery becomes overheated, the vacuum will automatically shut off. Wait until the battery temperature returns to normal, then the vacuum will work normally.

Care & Maintenance

Tips :

• Always use genuine parts to keep your warranty from becoming void.
•  If the filter or nozzle becomes clogged, the vacuum will stop working shortly after being turned on. To restore normal functions, clean the filter and/or nozzle.
• If the vacuum is not be used for an extended period, fully charge it, unplug its charger, and store it in a cool, low-humidity environment away from direct sunlight. To avoid over-discharging the battery, recharge the vacuum at least once every three months.

Cleaning the Vacuum
Wipe the vacuum with a soft dry cloth.

Cleaning the Dust Cup, Pre-Filter, and Cyclone Assembly
The vacuum’s cleaning ability will be reduced if the dust cup is filled to the “MAX” mark. To regain performance, empty the dust cup in a timely manner. Before emptying the cup, make sure the vacuum is disconnected from the power, and do not press its power button.

1. Press the dust cup bottom cover release button, then empty the contents.
   

2. Push the dust cup release switch in the direction indicated by the arrow, then gently remove the dust cup from the vacuum.

3. Remove the pre-filter first, then lift the handle of the cyclone assembly and turn it counterclockwise until it stops, then pull to lift out the cyclone assembly.

4. Wipe the dust cup with a soft wet cloth. Pay attention to wring out the discloth before using.

To reduce the risk of electric shock, do not rinse the dust cup with water.

5. Rinse the cyclone assembly and pre-filter until they are clean. After washing, air dry for at least 24 hours.

Note: It is recommended to clean the pre-filter at least once every 3 months and the cyclone system at least once every 6 months.

Installing the Dust Cup, Pre-Filter, and Cyclone Assembly

1. Insert the cyclone assembly vertically into the dust cup, and make sure that the handle of the cyclone assembly line up with the slot on the left side of the dust cup. Turn the handle clockwise until it locks, then flip the handle down.

2. Place the pre-filter with its front side facing up into the cyclone assembly.

3. Slightly tilt the dust cup so its slot aligns with the clip on the vacuum. Then gently push the dust cup until it clicks into place.

Cleaning the Filter
It is recommended to clean the filter once every 4 to 6 months.

1. Remove the dust cup as shown in the figure.

2. Remove the filter from the vacuum by pulling it down in the direction shown in the figure.

3. Clean the filter with clean water. Make sure you rotate the filter 360° to thoroughly and remove all dust caught in the filter. Lightly tap the filter several times to remove any excess dirt.

4. Allow the filter to air dry for 24 hours.

Note:

• Only use clean water to wash the filter. Do not use detergent.
• Do not attempt to clean the filter with a brush or finger.

Installing the Filter

1. Insert the filter into the vacuum and gently press down, as illustrated.

2. Reinstall the dust cup.

Cleaning the Smart Multi-Brush Bar

1. Turn the lock counterclockwise until it stops, then remove the roller brush from the smart multi-brush bar.

2. Use scissor to cut off the hairs and fibers that get stuck on the brush bar head. Wipe the dust from the notch and transparent cover with a dry cloth or paper towel. Thoroughly dry before use.

3. When it is dirty, rinse the roller brush with clean water until it is clean.

4. Stand the roller brush upright for at least 24 hours until it is fully dry.

Cleaning the Mini Electric Brush

1. Use a coin as illustrated to rotate the lock counterclockwise until you hear a click.

2. After unlocking the mini roller brush, remove it from the mini electric brush, then rinse and clean the brush head.

3. Stand the mini roller brush upright in a well-ventilated area for at least 24 hours until it is fully dry.

4. Once the mini roller brush is dry, reinstall it by following the disassembly steps in reverse.

Battery Pack
The vacuum contains a removable rechargeable lithium-ion battery pack which has a limited number of recharge cycles. After extended use, the battery pack may no longer hold a charge. If this happens, it means the battery pack has reached the end of its life cycle and needs to be replaced.

1. Press down the battery pack release button and slide the battery pack to the right, as illustrated, to remove it.
2. Install the new battery pack.

Specifications

Vacuum Cleaner

Model| VTT1| Charging Voltage| 34 V
Rated Power| 550 W| Rated Voltage| 29.6 V
Charging Time| Approx. 4 hours| Battery Capacity| 2900 mAh

（Nominal Capacity）

Smart Multi-Brush Bar
Model| ASF5
Rated Power| 40 W| Nominal Capacity| 29.6 V
Mini Electric Brush
Model| VPA3
Rated Power| 20 W| Rated Voltage| 29.6 V
Charger
Model| ZD024M340090US| AveErffiagcieeAnctyive| 87.01 %
Input| 100 – 2400.8VA~m50a-x60 Hz，| EffiLcoieandc(y10a%t L)ow| 77.01 %
Output| 34 V       0.9 A| NCoo-nlosaudmPpotiwoenr| 0.1 W
Rechargeable Lithium-Ion Battery Pack
Model| P2033-8S1P-PAA| Battery Capacity| 2900 mAh

（Nominal Capacity）

Nominal Voltage| 29.6 V| Energy| 81.4 Wh

The lithium-ion pack contains substances that are hazardous to the environment. Before disposing of the vacuum, please remove the battery pack, then discard or recycle it in accordance with local laws and regulations of the country or region it is used in.

FAQ

If the vacuum is not working properly, please refer to the table below.

Vacuum does not work.

| Vacuum is out of battery or low on power.| Fully charge the vacuum, then continue to use it.
Overheat protection mode triggered by a blockage.| Clean the suction openings or air duct. Wait until the vacuum cools down, then reactivate it.
The suction opening or air duct is blocked.| Clear any blockage from suction opening or air duct.

Weak suction force.

| Dust cup is full and/or filter assembly is clogged.| Empty the dust cup and clean the filter assembly.
Attachment is blocked.| Clear any blockage in the attachment.
Motor is making a strange noise.| Main suction opening or carbon fiber rod is blocked.| Clear any blockage in the main suction opening or extension rod.

The battery indicator does not light up when charging.

| The charger does not plug into the vacuum well.| Check whether the charger is properly plugged into the vacuum.
The battery is fully charged and went into sleep mode.| The vacuum can be used normally.
If the problem persists after ruling out the above two possibilities.| Please contact the after- sales service department for maintenance.
The vacuum charges slowly.| Battery temperature is too low or too high.| Wait until the battery’s temperature returns normal, then continue to use the vacuum.

Troubleshooting

If you need to pay attention to any abnormality during the use of the product, a prompt will be shown on the screen. You should follow the instructions on the screen to keep the performance normal.

For more information, please visit www.dreame-technology.com
Manufactured by : Dreame Trading (Tianjin) Co., Ltd.
Address: Room 2112-1-1, South District, Finance and Trade Center, No.6975 Yazhou Road, Dongjiang Bonded Port Area, Tianjin Pilot Free Trade Zone, Tianjin, China
Made in China

References

• Dreame Global | Smart Robot Vacuum Cleaners

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>