COSTWAY ES10052 52 Inch Ceiling Fan Lamp User Manual

COSTWAY ES10052 52 Inch Ceiling Fan Lamp

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP IT FOR FUTURE REFERENCE.

Please give us a chance to make it right and do better! Contact our friendly customer service department for help first. Replacements for missing or damaged parts will be shipped ASAP!

Follow Costway

Contact Us! Do NOT return this item.
Contact our friendly customer service department for help first.
E-mail:
US: cs.us@costway.com
UK: cs.uk@costway.com

Before You Start

• Please read all instructions carefully.
• Retain instructions for future reference.
• Separate and count all parts and hardware.
• Read through each step carefully and follow the proper order.
• We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
• Always place the product on a flat, steady and stable surface.
• Keep all small parts and packaging materials for this product away from babies and children as they potentially pose a serious choking hazard.

Safety Information

1. To reduce the risk or electric shock the electricity has box been before turned beginning off at of the circuit it allation. breaker or fuse

2. All wiring must be in accordance with the National Electrical Code Electrical NASJ/NFPA installation should 70-1999 be and performed locally by electrical qualified codes.
   licensed electrician.

3. The mounted outlet 35Ibs(15.9kg). Use and box and capable only support of UL reliably listed structure outlet supporting must boxes be securely marked “Acceptable for Fan Support of 35Ibs (15.9kg)or less.”

4. The fan must be mounted with a minimum of 7 ft. (2m)

5. Do not operate the reversing switch while the fan stop blades that are blades in motion. before you You must reverse turn the blade fan off the direction.

6. Do not place objects in the path of the blades.

7. To avoid personal injection who en damage working to the around the fan or and clothes eaning items the use fan.

8. Electrical diagrams are for reference only. Light kits that
   are suitable not for packed use with the fan model must be fan you UL-listed are and installing. marked proper Switches instructions must assembly. be packaged UL with General the Use light kits Switches. and Refer switches to therefor

9. After making electrical connections, spliced conductors the should outlet be box. turned The wires upward should and be pushed spread carefully apart ent-grounding with up into the
   grounded conductor on one conductor side of and the outlet equip box.

WARNING:

• To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.

• Remove the rubber motor stops on the bottom of the fan before installing the bladees or testing the motor.A

• To reduce the risk or fire or electric shock,do not use this fan with any solid-state speed control device.

• To avoid possible electric shock, turn the electricity off at the main fuse box before wiring.If you feel you do not have enough electrical wiring knowledge or experience, contact a licensed
  electrician.

• Electrical diagrams are for reference only. Optional use of any light kit shall be UL-listed and marked suitable for use with this fan.

• To reduce the risk of fire, electric shock or personal injury. mount to outlet box marked”

• Acceptable for fan support of 35 lbs.(15.9 kg)or less. and use the screws provided with the outlet box.

Pre-Installation

SPECIFICATION

The above data are for reference only, Actually the motor speed of each ceiling fan is a little different. Any products, Subject to actual products as standard.
NOTE:  These are approximate measures. They do not include the amps and wattage used by the light kit. Specifications & measurements shown are subject to± 5% variations.

TOOLS REQUIRED

HARDWARE INCLUDED

components table

PACKAGE CONTENTS

Installation of the hanging bracket (suspension part)

For wooden ceiling, use wood screw to drill on the wooden beam or the “junction box” to fix the hanging bracket (selection is made according to actual requirements of the customers).

STEP 1A-WOODEN CEILING

SWITCH OFF THE ELEC TRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.

1. Use the Mounting Bracket (A) as a guide, mark the spots where the 4 Self Tapping Screws (B) will be drilled.
2. Remove the Mounting Bracket (A), drill 4 holes for 3MM diameter, install the mounting bracket onto wooden ceiling with the 4 Self Tapping Screws (B) & Washers (C).
   IMPORTANT: SCREWS MUST BE TIGHTENED TILL SNUG

Note:  According to the ceiling of different materials, use different screws to fix the hanging bracket. Don’t fix the hanging bracket on the wood ceiling less than 12MM to prevent danger caused by loosening of screws. After the hanging bracket is completed, ensure that it can withstand the tension test of more than 68KG for safety.
For concrete ceiling, use the percussion bit with diameter 8mm to drill holes according to the length
of expansion screws. Then use the attached expansion screws to fix the hanging bracket onto
the ceiling (selection is made according to actual requirements of the customers).

STEP 2A-CONCRETE CEILING

SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.

1. Use the Mounting Bracket (A) as a guide, mark the spots where the 4 Expansion Bolts (B) will be drilled.
2. Remove the Mounting Bracket (A), drill 4 holes and insert 4 Expansion Bolts (B) into the concrete ceiling, install the mounting bracket and secure with Flat Washers (C), Spring Washers (D) and Nuts (E).
   IMPORTANT: SCREWS & NUTS MUST BE TIGHTENED TILL SNUG

Install the hanging part of the ceiling fan.

Install download assembly

1. Thread the suspender through the suspended clock and coupling cover.
2. The insert the tail of the suspender from the lifting head of the motor.
3. After the lateral pin is threaded out from the suspended head position, insert R type pin.
4. Tighten the lifting head screws.
5. Hang the fan of the hanging pipe into the hanger.

Assembly – Hanging the Fan

Making the electrical connections

WARNING: Each wire not supplied with this fan is designed to accept up to one 12-gauge house wire and two wires from the fan.If you have larger than 12-gauge house wiring or more than one house wire to connect to the fan wiring, consult an electrician for the proper size wire nuts to use.
IMPORTANT: Use the plastic wire connectors(BB) supplied with your fan. Secure the connectors with electrical tape and ensure there are no loose strands or connections.
WARNING: Remove the rubber motor stops on the bottom of fan before installing the blades or testing the motor.

1. The motor “green” wire to the “Ground wire” from outside Outlet Box.
2. The motor “white” wire to the “AC IN ”wire from outside Outlet Box.
3. The motor “black” wire to the “blue “wire to the “AC IN ”wire from outside Outlet Box.
4. Finally,put the connected wires in the hanger.

Install remote control

1. Carefully push the canopy to the bottom of the mounting bracket, make two sliding holes aligned to the two prominent screws on the mounting bracket, and then turn clockwise until tight.
2. Push the canopy ring to the bottom of the canopy, slide the inner holes aligned to the two prominent screws on the mounting bracket again, and turn the canopy ring clockwise until tight.

Preparing for mounting

1. Remove the mounting bracket from the canopy by loosening the two canopy screws located in the L shaped slots.
2. Remove and save the two canopy screws in the round holes. This will enable you to remove the mounting bracket

Assembly- Attaching the Fan Blades

**Attaching the blades to the arms

**

1. Pass the red washer through the screw.
2. Tighten the screw through the blade and tighten it on the arms.
3. Repeat the above steps to tighten the four sets of blades.

Fastening the blade arms to the motor

WARNING: Remove before installing the rubber the blades motor or stops testing on the bottom motor.
NOTE: Your fan features revolutionary advancements for quick and easy blade installation.Including an alignment post and captive blade arm screws.
NOTE: Your fan blades are reversible. Select the blade side finish which best accentuates your decor.

Assembly – Attaching the Lights

Connecting lamp wire

CAUTION: To reduce the risk of electric shock,disconnect the electrical circuit to the fan before installing the light fixture.

1. lnsert the “white” line in the switching box of the motor into the “white”line of the light and tie insulated rubber tape.
2. Insert the “blue”line in the switching box of the motor into the “blue”line of the light and tie insulated rubber tape.

Tighten the screw of the box cover.

1. Take the wire into the switching box of the motor
2. Align the opening of switching box of the light at switch locking position of the positive and negative rotation of the motors switching box. Place the cover screw in the screw of the switching box

lnstall the lamp shade & bulb

WARNING: Allow the shatter resistant bowl to cool completely before removing.
CAUTION: Make sure the power is off before attaching or removing the shatter resistant bowl.
CAUTION: Do not over tighten the hex nut,overtightening the hex nut may cause the shatter resistant bowl to break.

1. Select an E26 bulb with appropriate power and screw it onto the lamp holder.
2. According to the picture on the left, fix the acrylic sheet on the lamp in turn.

Operation

OPERATING YOUR FAN

The appropriate speed settings for warm or cool weather depends on factors such as the room size, ceiling height, and number of fans. The slide switch ( XX)controls the direction of the blades: forward (switch down)or reverse(switch up).
NOTE: Wait for the fan to stop before reversing the direction of the blade rotation

A Warm weather-(Forward )A downward airflow creates a cooling effect. This allows you to set your air conditioner on a higher setting without affecting your comfort.
B Cool weather-( Reverse )An upward airflow moves warm air off of the ceiling. This allows you to set your heating unit on a lower setting without affecting your comfort

Use of remote control

Care and Cleaning

WARNING: Make sure the power is off before cleaning your fan.

• Because of the fan’s natural movement, some connections may become loose.Check the support connections,brackets,and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the celling.
• Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor or the wood, or possibly cause an electric shock. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plathing is sealed with a lacquer to minimize discoloration or tarnishing.
• You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish.
• You do not need to oil your fan. The motor has permanently­lubricated sealed ball bearings.

Troubleshooting

Problem

| ****

Solution

The fan will not start.

| Check the main and branch circuit fuses or breakers.

Check the line wire connections to the fan and switch

wire connections in the switch housing.

The fan will not start.

| Ensure all motor housing screws are snug.

Ensure the screws that attach the fan blade bracket to the motor hub are tight.

Ensure the wire nut connetions are not rattling against each other or the interior wall of the switch housing.

Allow a 24-hour “breaking in” period. Most noises associated with a new fan disappear during this time.

If you are using the Ceiling Fan light kit,ensure the screws securing the glassware are tight.

Check that the light bulbs are also secure.

Ensure the canopy is at a short distance from the ceiling.It should not touch the ceiling.

Ensure your outlet box is secure and rubber isolator pads were used between the mounting plate and outlet box.

The fan wobbles.

| ****

Check that all blade and blade arm screws are secure.

Most fan wobble problems are caused when blade levels are unequal.

Check this level by selecting a point on the ceiling above the tip of one

of the blades.

Measure from a point on the center of each blade to the point on the ceiling.

Measure this distance.Rotate the fan until the next blade is positioned for measurement.

Repeat for each blade. Any measurement deviation should be within 1/8 in.

Run the fan for ten minutes.

If the fan continues to wobble please contact Customer Service and a balancing kit will be sent to you.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>