CHAUVET PROFESSIONAL OVATION REVE E3 Multi-Color LED Ellipsoidal User Guide

CHAUVET PROFESSIONAL OVATION REVE E3 Multi-Color LED EllipsoidalSafety

Notes

• The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than 10 ft (3 m) is not expected.
• If the external flexible cable or cord of this luminaire is damaged, it shall be replaced by a special cord or cord exclusively available from the manufacturer or his service agent.
• The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
• The luminaire is intended for professional use only.
• DO NOT open this product. It contains no user-serviceable parts.
• DO NOT look at the light source when the product is on.
• DO NOT operate this product outdoors or in any location where dust, excessive heat, water, or humidity may affect it (IP20).
• DO NOT leave any flammable material within 50 cm of this product while operating or connected to power.
• DO NOT operate this product if the housing, lenses, or cables appear damaged.
• DO NOT connect this product to a dimmer or rheostat.
• CAUTION: This product’s housing may be hot when lights are operating.
• CAUTION: When transferring product from extreme temperature environments, (e.g., cold truck to warm humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow product to fully acclimate to the surrounding environment before connecting it to power.
• USE a safety cable when mounting this product overhead.
• ONLY connect this product to a grounded and protected circuit.
• ONLY use the hanging/mounting bracket to carry this product.
• Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.
• In the event of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at higher temperatures.

QUICK REFERENCE GUIDE

AC Power
This product has an auto-ranging power supply that can work with an input voltage range of 100–240 VAC, 50/60 Hz. Power Linking
It is possible to link up to 3 Ovation Rêve E-3 products at 100 V, 4 products at 120 V, 7 products at 208 V, 8 products at 230 V, or 8 products at 240 V. Never exceed this number. Power-linking cords can be purchased separately.
AC Plug

To eliminate unnecessary wear and improve its lifespan, during periods of non- use completely disconnect the product from power via breaker or by unplugging it.About This Guide

Replacing the Fuse

1. Disconnect this product from power.
2. Using a Phillips-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove blown fuse and replace with a good fuse of the same type and rating.
4. Screw the fuse holder cap back in place and reconnect the power.

DMX Linking
The Ovation Rêve E-3 will work with a DMX controller using a 3- and 5-pin DMX serial connection. A DMX Primer is available from www.chauvetprofessional.com.
DMX Connection
The Ovation Rêve E-3 uses a 3- and 5-pin DMX data connection for its DMX personalities: 1Ch, 5Ch, 6Ch, 8Ch, 12Ch, 14Ch1, 14Ch2, 18Ch, and HSV. See the User Manual for information about connecting and configuring the product for DMX operation.
Master/Slave Connection
The Ovation Rêve E-3 uses the DMX data connection for its master/slave mode. See the User Manual for information about how to connect and configure the product for master/slave operation.
RDM (Remote Device Management)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate bi-directionally along existing DMX cabling. Check with the manufacturer or the DMX controller’s User Manual, as not all DMX controllers have this capability. The Ovation Rêve E-3 supports RDM protocol that allows feedback to make changes to menu map options. Download the User Manual from www.chauvetprofessional.com for more details.
USB Software Update
The Ovation Rêve E-3 allows for software update through USB using the built-in USB port. To update the software using USB flash drive, do the following:

1. Power on the fixture and plug the flash drive into the USB port.
2. Once the flash drive has been detected, the message “Upgrade Firmware” will be displayed. Press .
3. If a different message appears on the display, search for the updated software in the Main Menu (Update Firmware) and select from Only This Unit, Multiple Units, or Other Fixture Type. A list of the software update files will be displayed.
4. Select the file that needs to be uploaded. The message “Are you sure?” will be displayed. Press .
5. If the selected file is correct, the upgrade will be completed. Restart the fixture.
6. If the selected file is incorrect, the upgrade will fail, and the display will go back to the main interface. Repeat steps 1-3 using the correct file.

The .chl format file needs to be placed in the OVATION folder in the USB flash drive.
The “Other Fixture Type” option can only be selected for connected products compatible with the Upload 03 (the first 2 digits of the item code must be 03).

Lens Tubes

The following lens tubes are available for purchase:

• 19°, 26°, 36°, and 50° with gel frame (6.25 in/159 mm accessories)
• 5° zoom gel frame (14 in/356 mm)
• 10° zoom gel frame (12 in/304 mm)
• 14°, 15–30° and 25°–50° zoom gel frame (7.5 in/191 mm accessories)

Mounting
Before mounting this product, read the Safety Notes. Use at least one mounting point per product. Make sure the mounting clamps can support the weight of the product. For the Chauvet line of mounting clamps, go to:
http://trusst.com/productcategory/truss-clamps/.

Product Mounting Diagram

Overhead Mounting

Adjustable Yoke
The Ovation Rêve E-3 comes with an adjustable yoke for mounting in low- clearance areas. To modify the height of the yoke, do the following:

1. Loosen the bracket adjustment knobs on both sides of the fixture.
2. On each side of the fixture, remove the two screws and loosen the bolt attaching the plate to the mounting bracket.
3. Using the screw holes as guide, adjust the position of the mounting bracket to achieve the desired height of the yoke.
4. Put the screws back in place, and tighten the bolts and the bracket adjustment knobs.

Virtual Color Wheel
The Ovation Rêve E-3 includes a feature called the Virtual Color Wheel (VCW). This feature is available as a standalone control mode for manual use and as a control channel in select DMX personalities. More than 30 premixed colors, custom blended by Chauvet engineers, are available to call up for easier programming. The DMX values used to mix these colors are provided below. The overall intensity of the Ovation fixture can be adjusted to more closely replicate familiar industry-standard colors. A chart is available on www.chauvetprofessional.com to compare Chauvet’s premixed colors with popular gel colors. This chart is for comparison purposes only and is not an assertion that Chauvet’s premixed colors match any of the gel colors listed.
Virtual Color Wheel Chart

DMX Channel Value| Display Readout| Red Value| Green Value| Blue Value| Amber Value| Mint Value
---|---|---|---|---|---|---
000 ó 005| —| —| —| —| —| —
006 ó 013| C3050 – Md Yellow| 255| 225| 0| 255| 37
014 ó 021| C3040 – Lt Yellow| 255| 177| 3| 255| 37
022 ó 028| C3240 – Amb Yellow| 255| 220| 0| 255| 0
029 ó 035| C2340 – VLt Amber| 195| 0| 15| 255| 57
036 ó 043| C2040 – Lt Amber| 255| 0| 11| 255| 61
044 ó 051| C2050 – Md Amber| 255| 53| 0| 255| 17
052 ó 059| C2060 – Dk Amber| 255| 8| 0| 255| 17
060 ó 067| C1050 – Lt Red| 255| 0| 3| 14| 0
068 ó 075| C1080 – Md Red| 255| 0| 2| 0| 0
076 ó 083| C1020 – NC Pink| 255| 75| 62| 255| 73
084 ó 091| C1030 – Md Pink| 255| 75| 57| 255| 41
092 ó 099| C1630 – Dk Pink| 218| 77| 57| 255| 61
100 ó 107| C1250 – Md Red Amber| 255| 0| 9| 168| 0
108 ó 115| C1060 – Dk Red Amber| 255| 5| 9| 36| 0
116 ó 121| C1650 – Magenta| 255| 3| 62| 255| 12
122 ó 130| C6170 – Dk Magenta| 255| 0| 55| 0| 0
131 ó 138| C6020 – Lt Lavender| 255| 220| 93| 255| 44
139 ó 146| C5030 – Lt Blue| 0| 255| 159| 112| 78
147 ó 154| C5020 – VLt Blue| 0| 215| 145| 196| 65
155 ó 162| C5430 – Lt Blue2| 0| 215| 132| 52| 92
163 ó 170| C5070 – Blue| 0| 195| 188| 0| 19
171 ó 178| C5050 – Md Blue| 0| 163| 190| 0| 68
179 ó 186| C5060 – Dk Blue| 0| 128| 193| 0| 38
187 ó 194| C5690 – Indigo| 53| 9| 255| 0| 0
195 ó 202| C5080 – VDk Blue| 7| 84| 116| 0| 0
203 ó 210| C5081 – VDk Blue2| 11| 82| 139| 0| 0
211 ó 218| C4370 – Yel Green| 0| 255| 2| 25| 0
219 ó 226| C4070 – Green| 0| 255| 9| 0| 175
227 ó 234| C4550 – Turquoise| 0| 255| 87| 96| 255
235 ó 242| C4560 – Aqua| 0| 255| 98| 44| 255
243 ó 250| C4570 – Blue Green| 0| 255| 26| 8| 0
251 ó 255| —| —| —| —| —| —

Note: The colors above are simulated renditions of the color output produced compared with other similar incandescent products. Chauvet makes no guarantee of the color output accuracy.The Ovation Rêve E-3 Quick Reference Guide (QRG) has basic product information such as connection, mounting, menu options, and DMX values. Download the User Manual from www.chauvetprofessional.com for more details.

Color Temperature Chart

Color Temperature| Red Value| Green Value| Blue Value| Amber Value| Mint Value
---|---|---|---|---|---
2800K| 253| 0| 25| 255| 145
2900K| 253| 3| 28| 255| 153
3000K| 251| 5| 33| 255| 161
3100K| 248| 7| 36| 255| 169
3200K| 245| 9| 45| 255| 173
3300K| 242| 13| 47| 255| 182
3400K| 237| 22| 53| 255| 185
3500K| 230| 30| 58| 255| 185
3600K| 225| 40| 64| 255| 185
3700K| 221| 48| 70| 255| 185
3800K| 220| 48| 74| 255| 197
3900K| 220| 50| 79| 255| 203
4000K| 210| 58| 84| 255| 203
4100K| 205| 63| 88| 255| 203
4200K| 199| 68| 95| 255| 204
4300K| 189| 69| 98| 255| 204
4400K| 183| 71| 103| 255| 204
4500K| 174| 78| 107| 255| 204
4600K| 170| 80| 112| 255| 204
4700K| 166| 89| 119| 255| 204
4800K| 164| 98| 123| 255| 203
4900K| 163| 100| 129| 255| 205
5000K| 163| 103| 137| 255| 206
5100K| 163| 108| 142| 255| 208
5200K| 163| 116| 147| 255| 208
5300K| 163| 118| 156| 255| 210
5400K| 162| 122| 162| 255| 216
5500K| 162| 124| 166| 255| 224
5600K| 162| 127| 172| 255| 229
5700K| 159| 127| 177| 255| 231
6000K| 158| 134| 192| 241| 231
6500K| 152| 152| 206| 225| 231
7000K| 144| 157| 224| 218| 231
7500K| 127| 172| 238| 218| 231
8000K| 122| 175| 245| 200| 231

The color temperatures above are simulated renditions of the color output produced compared with a tungsten lamp at the specified color temperature. Chauvet makes no guarantee of the color output accuracy.

Color Temperature DMX Chart

DMX Channel| Color Temperature| DMX Channel| Color Temperature| DMX Channel| Color Temperature
---|---|---|---|---|---
000 ó 005| No function| 084 ó 090| 3900–4000K| 168 ó 174| 5100–5200K
006 ó 013| 2800–2900K| 091 ó 097| 4000–4100K| 175 ó 181| 5200–5300K
014 ó 020| 2900–3000K| 098 ó 104| 4100–4200K| 182 ó 188| 5300–5400K
021 ó 027| 3000–3100K| 105 ó 111| 4200–4300K| 189 ó 195| 5400–5500K
028 ó 034| 3100–3200K| 112 ó 118| 4300–4400K| 196 ó 202| 5500–5600K
035 ó 041| 3200–3300K| 119 ó 125| 4400–4500K| 203 ó 209| 5600–5700K
042 ó 048| 3300–3400K| 126 ó 132| 4500–4600K| 210 ó 216| 5700–6000K
049 ó 055| 3400–3500K| 133 ó 139| 4600–4700K| 217 ó 223| 6000–6500K
056 ó 062| 3500–3600K| 140 ó 146| 4700–4800K| 224 ó 230| 6500–7000K
063 ó 069| 3600–3700K| 147 ó 153| 4800–4900K| 231 ó 237| 7000–7500K
070 ó 076| 3700–3800K| 154 ó 160| 4900–5000K| 238 ó 244| 7500–8000K
077 ó 083| 3800–3900K| 161 ó 167| 5000–5100K| 245 ó 255| 8000K

Control Panel Description

selected value into the selected function
< UP>| Navigates upwards through the menu list or increases the numeric value when in a function
< DOWN>| Navigates downwards through the menu list or decreases the numeric value when in a function
< FOCUS>| Sets fixture into Focus Mode, which takes the unit to full power for easy focusing without changing any other fixture settings. Press again to release from Focus Mode.

Menu Map
Refer to the Ovation Rêve E-3 product page on www.chauvetprofessional.com for the latest menu map.

(*highest channel restricted to personality chosen)

DMX Channel

| 1Ch| Virtual Color Wheel| 1-channel: dimmer
Color Temperature
Manual Color Mixer
5Ch| 5-channel: dimmer, virtual color wheel (VCW), color

temperature, hue, gobo rotator

6Ch| 6-channel: red, green, blue, amber, mint, gobo rotator
8Ch| 8-channel: dimmer, RGBAM, strobe, gobo rotator
12Ch| 12-channel: 16-bit dimmer, RGBAM, strobe, VCW,

color temperature, hue, gobo rotator

14Ch1| 14-channel: dimmer, RGBAM, strobe, VCW, color

temperature, hue, auto programs, auto speed, control, gobo rotator

14Ch2| 14-channel: 16-bit dimmer, 16-bit RGBAM, strobe,

gobo rotator

18Ch| 18-channel: 16-bit RGBAM and dimmer, strobe,

VCW, color temperature, hue, control, gobo rotator

HSV| 4-channel: hue, saturation, value, gobo rotator

Virtual Color Wheel

|

Virtual Color Wheel

| C3050 – Md Yellow

C3040 – Lt Yellow C3240 – Amb Yellow C2340 – VLt Amber C2040 – Lt Amber C2050 – Md Amber C2060 – Dk Amber C1050 – Lt Red C1080 – Md Red C1020 – NC Pink

C1030 – Md Pink C1630 – Dk Pink C1250 – Md Red Amber

C1060 – Dk Red Amber C1650 – Magenta C6170 – Dk Magenta C6020 – Lt Lavender C5030 – Lt Blue

C5020 – VLt Blue C5430 – Lt Blue 2 C5070 – Blue C5050 – Md Blue C5060 – Dk Blue C5690 – Indigo C5080 – VDk Blue C5081 – VDk Blue 2

|

Dimmer 000–255

|

Virtual Color Wheel simulates the output of each gel color. Refer to the Virtual Color Wheel Chart for specific values.

Virtual Color Wheel

|

Virtual Color Wheel

| C4370 – Yel Green

C4070 – Green C4550 – Turquoise C4560 – Aqua C4570 – Blue Green

|

Dimmer 000–255

|

Virtual Color Wheel simulates the output of each gel color. Refer to the Virtual Color Wheel Chart for specific values.

Color Temperature

| 2800K

2900K

3000K

3100K

3200K

3300K

3400K

3500K

3600K

3700K

3800K

3900K

4000K

4100K

4200K

4300K

4400K

4500K

4600K

4700K

4800K

4900K

5000K

5100K

5200K

5300K

5400K

5500K

5600K

5700K

6000K

6500K

7000K

7500K

8000K

|

Dimmer

|

0–255

|

Preset white color temperatures. Emulates a tungsten lamp at the specified color temperature. Refer to the Color Temperature Chart for specific values.

Hue

|

-25–25

Manual Color Mixer

| Red

Green Blue Amber Mint

|

000–255

|

Combines red, green, blue, amber, and mint to make a custom color (0–100%)

Auto Show| Auto 1–5| 1–100| Selects automatic programs and auto program speed
Red Shift| On| Mimics halogen lamp dimming
Off
Gobo Rotator| 000–255| Controls the gobo rotator
Master/Slave| Master| Receives DMX signal from the DMX controller (master)
Slave| Receives DMX signal from the master unit

Dimmer Curve

| SCurve

Linear Square

Inverse Square

|

Sets the dimmer curve

Dimmer Mode| Off| Linear dimmer
Dimmer 1–3| Dimming curves, from fast ( Dimmer 1 ) to slow ( Dimmer 3 )
Main Level| Programming Levels| Description
---|---|---

Color Calibration

| Off| Deactivates color calibration

User Calibration

| Red|

125–255

| Sets red LED maximum value
Green| Sets green LED maximum value
Blue| Sets blue LED maximum value
Amber| Sets amber LED maximum value
Mint| Sets mint LED maximum value
Factory Calibration| Uses factory default white setting

LED

Frequency

| 600Hz

1200Hz

2000Hz

4000Hz

6000Hz

25KHz

|

Sets the PWM output frequency

Fan Mode

| Auto| Sets the fan to auto mode
On| Sets the fan to always on
Off| Sets the fan to always off
Silent| Sets the fan to silent

Back Light

| 10S| Turns off display backlight after 10 seconds of inactivity
30S| Turns off display backlight after 30 seconds of inactivity
2Min| Turns off display backlight after 2 minutes of inactivity
Always On| Display backlight always on
Gobo Power| On

Off

| Enables/disables gobo power output

Information

| Fixture Hours| _ _H| Shows total hours the product has been powered on
LED Hours| _ _H| Shows total hours the LED has been powered on
Version| V.| Shows current firmware version
UID| | Shows product UID

Update Firmware

| Only This Unit| .CHL| Selects an update file for this product, or shows “ No such file! ”
…
Multiple Units| .CHL| Selects an update file for this and connected

Ovation Rêve E-3 products, or shows “ No such file! ”

…
Other Fixture Type| .CHL| Selects an update file for other connected products, or shows “ No such file! ”
…
Reset Factory| No| Resets settings to factory default
Yes

WARNING: When operating in Fan Mode: Off and Fan Mode: Silent, the fixture will become hotter to the touch than when using other fan modes. Use proper protective equipment to prevent burns. Keep a safe distance from flammable objects.
NOTICE: When operating in Fan Mode: Off and Fan Mode: Silent, output of the fixture will be reduced and will not reach the same levels as when using other fan modes.

DMX Values HSV

191 ó 192

| Clockwise rotation, fast to slow

Stop

 |  | 193 ó 255| Counterclockwise rotation, slow to fast

18Ch

011 ó 255

| No function

Strobe, slow to fast

14| Virtual color wheel| 000 ó 255| Refer to Virtual Color Wheel Chart
15| Color temperature| 000 ó 255| Refer to Color Temperature DMX Chart
16| Hue| 000 ó 000| 0
001 ó 255| -25–25
 |  | 000 ó 007| No function
 |  | 008 ó 015| Dimmer reset
 |  | 016 ó 023| Red shift on
 |  | 024 ó 031| Red shift off
 |  | 032 ó 039| S-curve dimmer
 |  | 040 ó 047| Linear dimmer
 |  | 048 ó 055| Square dimmer curve

17

| Control

(hold for 3 seconds)

| 056 ó 063

064 ó 071

072 ó 079

| Inverse square dimmer curve Dimmer speed mode OFF

Dimmer speed 1 (fastest)

 |  | 080 ó 087| Dimmer speed 2
 |  | 088 ó 095| Dimmer speed 3 (slowest)
 |  | 096 ó 103| Fan auto
 |  | 104 ó 111| Fan on
 |  | 112 ó 119| Fan off
 |  | 120 ó 127| Fan silent
 |  | 128 ó 255| Reserved for future use
 |  | 000 ó 127| Index
18| Gobo rotator| 128 ó 190

191 ó 192

| Clockwise rotation, fast to slow

Stop

 |  | 193 ó 255| Counterclockwise rotation, slow to fast

14Ch1

011 ó 255

| No function

Strobe, slow to fast

8| Virtual color wheel| 000 ó 255| Refer to Virtual Color Wheel Chart
9| Color temperature| 000 ó 255| Refer to Color Temperature DMX Chart
10| Hue| 000 ó 000

001 ó 255

| 0

-25–25

111 ó 160

| Auto program 2

Auto program 3

 |  | 161 ó 210| Auto program 4
 |  | 211 ó 255| Auto program 5
12| Auto speed| 000 ó 255| Auto speed, slow to fast
 |  | 000 ó 007| No function
 |  | 008 ó 015| Dimmer reset
 |  | 016 ó 023| Red shift on
 |  | 024 ó 031| Red shift off
 |  | 032 ó 039| S-curve dimmer
 |  | 040 ó 047| Linear dimmer
 |  | 048 ó 055| Square dimmer curve

13

| Control

(hold for 3 seconds)

| 056 ó 063

064 ó 071

072 ó 079

| Inverse square dimmer curve Dimmer speed mode OFF

Dimmer speed 1 (fastest)

 |  | 080 ó 087| Dimmer speed 2
 |  | 088 ó 095| Dimmer speed 3 (slowest)
 |  | 096 ó 103| Fan auto
 |  | 104 ó 111| Fan on
 |  | 112 ó 119| Fan off
 |  | 120 ó 127| Fan silent
 |  | 128 ó 255| Reserved for future use
 |  | 000 ó 127| Index
14| Gobo rotator| 128 ó 190

191 ó 192

| Clockwise rotation, fast to slow

Stop

 |  | 193 ó 255| Counterclockwise rotation, slow to fast

14Ch2

011 ó 255

| No function

Strobe, slow to fast

14

| ****

Gobo rotator

| 000 ó 127

128 ó 190

191 ó 192

193 ó 255

| Index

Clockwise rotation, fast to slow Stop

Counterclockwise rotation, slow to fast

12Ch

011 ó 255

| No function

Strobe, slow to fast

9| Virtual color wheel| 000 ó 255| Refer to Virtual Color Wheel Chart
10| Color temperature| 000 ó 255| Refer to Color Temperature DMX Chart
11| Hue| 000 ó 000

001 ó 255

| 0

-25–25

12

| ****

Gobo rotator

| 000 ó 127

128 ó 190

191 ó 192

193 ó 255

| Index

Clockwise rotation, fast to slow Stop

Counterclockwise rotation, slow to fast

8Ch

011 ó 255

| No function

Strobe, slow to fast

8

| ****

Gobo rotator

| 000 ó 127

128 ó 190

191 ó 192

193 ó 255

| Index

Clockwise rotation, fast to slow Stop

Counterclockwise rotation, slow to fast

6Ch

191 ó 192

| Clockwise rotation, fast to slow

Stop

 |  | 193 ó 255| Counterclockwise rotation, slow to fast

5Ch

Chart_
3| Color temperature| 000 ó 255| Refer to Color Temperature DMX Chart
4| Hue| 000 ó 000| 0
001 ó 255| -25–25
 |  | 000 ó 127| Index
5| Gobo rotator| 128 ó 190

191 ó 192

| Clockwise rotation, fast to slow

Stop

 |  | 193 ó 255| Counterclockwise rotation, slow to fast

1Ch

Disclaimer
The information and specifications contained in this QRG are subject to change without notice.

FCC Compliance

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Contact
Outside the U.S., U.K., Ireland, Benelux, France, Germany, or Mexico, contact a distributor to request support or return a product. Refer to Contact Us at the end of this QRG for contact information.

What is Included

1. Ovation Rêve E-3
2. Seetronic Powerkon
3. Soft focus filter
4. Ovation metal gobo holder
5. Quick Reference Guide

This device complies with Part 15 Part B of the FCC Rules. Operation is subject to the following two conditions:

LIMITED WARRANTY

FOR WARRANTY REGISTRATION AND COMPLETE TERMS AND CONDITIONS PLEASE VISIT OUR WEBSITE. For Customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration.
For Customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu /warranty-registration/.
Chauvet warrants that this product shall be free from defects in material and workmanship under normal use, for the period specified in and subject to the exclusions and limitations set forth in, the full limited warranty on our website. This warranty extends only to the original purchaser of the product and is not transferable. To exercise rights under this warranty, the customer must provide proof of purchase in the form of an original sales receipt from an authorized dealer that shows the product name and date of purchase. THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES. This warranty gives the customer specific legal rights. The customer may also have other rights that vary from state to state and country to country. This warranty is valid only in the United States, United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, Germany and Mexico. For warranty terms in other countries, please consult a local distributor.

• Sunrise, FL 33351
• Fax: (954) 756-8015Address: 5200 NW 108th Ave.
• Voice: 844-393-7575
• Voice: 954-577-4455
• Email: chauvetcs@chauvetlighting.com
• Fax: 954-929-5560
• Address: Unit 1C
• Email: UKtech@chauvetlighting.eu
• Toll Free: 800-762-1084
• Website: www.chauvetprofessional.com

Brookhill Road Industrial Estate

• Pinxton, Nottingham, UK
• Website: www.chauvetprofessional.eu NG16 6NT
• Voice: +44 (0) 1773 511115
• Address: Stokstraat 18
• Email: BNLtech@chauvetlighting.eu
• Fax: +44 (0) 1773 511110

9770 Kruishoutem

Belgium

• Website: www.chauvetprofessional.eu
• Voice: +32 9 388 93 97
• Address: 3, Rue Ampère
• 91380 Chilly-Mazarin
• Email: FRtech@chauvetlighting.fr

France

• Website: www.chauvetprofessional.eu
• Voice: +33 1 78 85 33 59
• Address: Bruno-Bürgel-Str. 11 28759 Bremen
•  Email: DEtech@chauvetlighting.de

Germany

• Website: www.chauvetprofessional.eu
• Voice: +49 421 62 60 20
• Address: Av. de las Partidas 34 – 3B

(Entrance by Calle 2)

• Email: servicio@chauvet.com.mx

Zona Industrial Lerma

• Website: www.chauvetprofessional.mx

Visit the applicable website above to verify our contact information and instructions to request support. Outside the U.S., U.K., Ireland, Benelux, France, Germany, or Mexico, contact the dealer of record.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>